[ Upstream commit 0e90dfa7a8d817db755c7b5d89d77b9c485e4180 ]
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a57d8c217aadac75530b8e7ffb3a3e1b7bfd0330 ]
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6a52e73368038f47f6618623d75061dc263b26ae upstream.
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c73c57081b3d59aa99093fbedced32ea02620cd3 ]
Commit 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).
And commit a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.
The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:
- ICMP6 neighbor solicitation messages are unregistered multicast
packets as far as the bridge is concerned. So if we stop flooding
multicast, the outside world cannot ping the bridge device's IPv6
link-local address.
- There might be foreign interfaces bridged with our DSA switch ports
(sending a packet towards the host does not necessarily equal
termination, but maybe software forwarding). So if there is no one
interested in that multicast traffic in the local network stack, that
doesn't mean nobody is.
- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
the bridge is concerned. This should reach the CPU port.
- The switch driver might not do FDB partitioning. And since we don't
even bother to do more fine-grained flood disabling (such as "disable
flooding _from_port_N_ towards the CPU port" as opposed to "disable
flooding _from_any_port_ towards the CPU port"), this breaks standalone
ports, or even multiple bridges where one has an IGMP querier and one
doesn't.
Reverting the logic makes all of the above work.
Fixes: a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7df4e7449489d82cee6813dccbb4ae4f3f26ef7b ]
Qingfang points out that when a bridge with the default settings is
created and a port joins it:
ip link add br0 type bridge
ip link set swp0 master br0
DSA calls br_multicast_router() on the bridge to see if the br0 device
is a multicast router port, and if it is, it enables multicast flooding
to the CPU port, otherwise it disables it.
If we look through the multicast_router_show() sysfs or at the
IFLA_BR_MCAST_ROUTER netlink attribute, we see that the default mrouter
attribute for the bridge device is "1" (MDB_RTR_TYPE_TEMP_QUERY).
However, br_multicast_router() will return "0" (MDB_RTR_TYPE_DISABLED),
because an mrouter port in the MDB_RTR_TYPE_TEMP_QUERY state may not be
actually _active_ until it receives an actual IGMP query. So, the
br_multicast_router() function should really have been called
br_multicast_router_active() perhaps.
When/if an IGMP query is received, the bridge device will transition via
br_multicast_mark_router() into the active state until the
ip4_mc_router_timer expires after an multicast_querier_interval.
Of course, this does not happen if the bridge is created with an
mcast_router attribute of "2" (MDB_RTR_TYPE_PERM).
The point is that in lack of any IGMP query messages, and in the default
bridge configuration, unregistered multicast packets will not be able to
reach the CPU port through flooding, and this breaks many use cases
(most obviously, IPv6 ND, with its ICMP6 neighbor solicitation multicast
messages).
Leave the multicast flooding setting towards the CPU port down to a driver
level decision.
Fixes: 010e269f91 ("net: dsa: sync up switchdev objects and port attributes when joining the bridge")
Reported-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8b17a0bd96065e4511858689916bb729dbb881b ]
TX timestamps are sent by SJA1110 as Ethernet packets containing
metadata, so they are received by the tagging driver but must be
processed by the switch driver - the one that is stateful since it
keeps the TX timestamp queue.
This means that there is an sja1110_process_meta_tstamp() symbol
exported by the switch driver which is called by the tagging driver.
There is a shim definition for that function when the switch driver is
not compiled, which does nothing, but that shim is not effective when
the tagging protocol driver is built-in and the switch driver is a
module, because built-in code cannot call symbols exported by modules.
So add an optional dependency between the tagger and the switch driver,
if PTP support is enabled in the switch driver. If PTP is not enabled,
sja1110_process_meta_tstamp() will translate into the shim "do nothing
with these meta frames" function.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b6e638b4be2ad77f61fb93b4e1776c6ccc2edab ]
Upcoming patches will add tag_8021q related logic to switch.c and
port.c, in order to allow it to make use of cross-chip notifiers.
In addition, a struct dsa_8021q_context *ctx pointer will be added to
struct dsa_switch.
It seems fairly low-reward to #ifdef the *ctx from struct dsa_switch and
to provide shim implementations of the entire tag_8021q.c calling
surface (not even clear what to do about the tag_8021q cross-chip
notifiers to avoid compiling them). The runtime overhead for switches
which don't use tag_8021q is fairly small because all helpers will check
for ds->tag_8021q_ctx being a NULL pointer and stop there.
So let's make it part of dsa_core.o.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The blamed commit added a new field to struct switchdev_notifier_fdb_info,
but did not make sure that all call paths set it to something valid.
For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE
notifier, and since the 'is_local' flag is not set, it contains junk
from the stack, so the bridge might interpret those notifications as
being for local FDB entries when that was not intended.
To avoid that now and in the future, zero-initialize all
switchdev_notifier_fdb_info structures created by drivers such that all
newly added fields to not need to touch drivers again.
Fixes: 2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB notifications")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the checksum calculation is offloaded to the network device (e.g due to
NETIF_F_HW_CSUM inherited from the DSA master device), the calculated
layer 4 checksum is incorrect. This is since the DSA tag which is placed
after the layer 4 data is considered as being part of the daa and thus
errorneously included into the checksum calculation.
To avoid this, always calculate the layer 4 checksum in software.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skb_put() that is used by tail taggers to make room for the
DSA tag must only be called for linearized SKBS. However in case that the
slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the
SKB passed to the slaves transmit function may not be linearized.
Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags
for tail taggers.
Furthermore since the tagging protocol can be changed at runtime move the
code for setting up the slaves features into dsa_slave_setup_tagger().
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was not caught because there is no switch driver which implements
the .port_bridge_join but not .port_bridge_leave method, but it should
nonetheless be fixed, as in certain conditions (driver development) it
might lead to NULL pointer dereference.
Fixes: f66a6a69f9 ("net: dsa: permit cross-chip bridging between all trees in the system")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core has a layered structure, and even though we end up
returning 0 (success) to user space when setting a bonding/team upper
that can't be offloaded, some parts of the framework actually need to
know that we couldn't offload that.
For example, if dsa_switch_lag_join returns 0 as it currently does,
dsa_port_lag_join has no way to tell a successful offload from a
software fallback, and it will call dsa_port_bridge_join afterwards.
Then we'll think we're offloading the bridge master of the LAG, when in
fact we're not even offloading the LAG. In turn, this will make us set
skb->offload_fwd_mark = true, which is incorrect and the bridge doesn't
like it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we join a bridge that already has some local addresses pointing to
itself, we do not get those notifications. Similarly, when we leave that
bridge, we do not get notifications for the deletion of those entries.
The only switchdev notifications we get are those of entries added while
the DSA port is enslaved to the bridge.
This makes use cases such as the following work properly (with the
number of additions and removals properly balanced):
ip link add br0 type bridge
ip link add br1 type bridge
ip link set br0 address 00:01:02:03:04:05
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 up
ip link set swp1 up
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 up
ip link set br1 up
ip link del br1 # 00:01:02:03:04:05 still installed on the CPU port
ip link del br0 # 00:01:02:03:04:05 finally removed from the CPU port
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
(a) "dev" is a bridge port which the DSA switch tree offloads, but is
otherwise not a dsa slave (such as a LAG netdev), or
(b) "dev" is the bridge net device itself
then strange things happen to the dev_hold/dev_put pair:
dsa_schedule_work() will still be called with a DSA port that offloads
that netdev, but dev_hold() will be called on the non-DSA netdev.
Then the "if" condition in dsa_slave_switchdev_event_work() does not
pass, because "dev" is not a DSA netdev, so dev_put() is not called.
This results in the simple fact that we have a reference counting
mismatch on the "dev" net device.
This can be seen when we add support for host addresses installed on the
bridge net device.
ip link add br1 type bridge
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 master br1
ip link del br1
[ 968.512278] unregister_netdevice: waiting for br1 to become free. Usage count = 5
It seems foolish to do penny pinching and not add the net_device pointer
in the dsa_switchdev_event_work structure, so let's finally do that.
As an added bonus, when we start offloading local entries pointing
towards the bridge, these will now properly appear as 'offloaded' in
'bridge fdb' (this was not possible before, because 'dev' was assumed to
only be a DSA net device):
00:01:02:03:04:05 dev br0 vlan 1 offload master br0 permanent
00:01:02:03:04:05 dev br0 offload master br0 permanent
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge supports a legacy way of adding local (non-forwarded) FDB
entries, which works on an individual port basis:
bridge fdb add dev swp0 00:01:02:03:04:05 master local
As well as a new way, added by Roopa Prabhu in commit 3741873b4f
("bridge: allow adding of fdb entries pointing to the bridge device"):
bridge fdb add dev br0 00:01:02:03:04:05 self local
The two commands are functionally equivalent, except that the first one
produces an entry with fdb->dst == swp0, and the other an entry with
fdb->dst == NULL. The confusing part, though, is that even if fdb->dst
is swp0 for the 'local on port' entry, that destination is not used.
Nonetheless, the idea is that the bridge has reference counting for
local entries, and local entries pointing towards the bridge are still
'as local' as local entries for a port.
The bridge adds the MAC addresses of the interfaces automatically as
FDB entries with is_local=1. For the MAC address of the ports, fdb->dst
will be equal to the port, and for the MAC address of the bridge,
fdb->dst will point towards the bridge (i.e. be NULL). Therefore, if the
MAC address of the bridge is not inherited from either of the physical
ports, then we must explicitly catch local FDB entries emitted towards
the br0, otherwise we'll miss the MAC address of the bridge (and, of
course, any entry with 'bridge add dev br0 ... self local').
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge automatically creates local (not forwarded) fdb entries
pointing towards physical ports with their interface MAC addresses.
For switchdev, the significance of these fdb entries is the exact
opposite of that of non-local entries: instead of sending these frame
outwards, we must send them inwards (towards the host).
NOTE: The bridge's own MAC address is also "local". If that address is
not shared with any port, the bridge's MAC is not be added by this
functionality - but the following commit takes care of that case.
NOTE 2: We mark these addresses as host-filtered regardless of the value
of ds->assisted_learning_on_cpu_port. This is because, as opposed to the
speculative logic done for dynamic address learning on foreign
interfaces, the local FDB entries are rather fixed, so there isn't any
risk of them migrating from one bridge port to another.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is able to install FDB entries towards the CPU port for addresses
which were dynamically learnt by the software bridge on foreign
interfaces that are in the same bridge with a DSA switch interface.
Since this behavior is opportunistic, it is guarded by the
"assisted_learning_on_cpu_port" property which can be enabled by drivers
and is not done automatically (since certain switches may support
address learning of packets coming from the CPU port).
But if those FDB entries added on the foreign interfaces are static
(added by the user) instead of dynamically learnt, currently DSA does
not do anything (and arguably it should).
Because static FDB entries are not supposed to move on their own, there
is no downside in reusing the "assisted_learning_on_cpu_port" logic to
sync static FDB entries to the DSA CPU port unconditionally, even if
assisted_learning_on_cpu_port is not requested by the driver.
For example, this situation:
br0
/ \
swp0 dummy0
$ bridge fdb add 02:00:de:ad:00:01 dev dummy0 vlan 1 master static
Results in DSA adding an entry in the hardware FDB, pointing this
address towards the CPU port.
The same is true for entries added to the bridge itself, e.g:
$ bridge fdb add 02:00:de:ad:00:01 dev br0 vlan 1 self local
(except that right now, DSA still ignores 'local' FDB entries, this will
be changed in a later patch)
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DSA master implements strict address filtering, then the unicast
and multicast addresses kept by the DSA CPU ports should be synchronized
with the address lists of the DSA master.
Note that we want the synchronization of the master's address lists even
if the DSA switch doesn't support unicast/multicast database operations,
on the premises that the packets will be flooded to the CPU in that
case, and we should still instruct the master to receive them. This is
why we do the dev_uc_add() etc first, even if dsa_port_notify() returns
-EOPNOTSUPP. In turn, dev_uc_add() and friends return error only if
memory allocation fails, so it is probably ok to check and propagate
that error code and not just ignore it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same concerns expressed for host MDB entries are valid for host FDBs
just as well:
- in the case of multiple bridges spanning the same switch chip, deleting
a host FDB entry that belongs to one bridge will result in breakage to
the other bridge
- not deleting FDB entries across DSA links means that the switch's
hardware tables will eventually run out, given enough wear&tear
So do the same thing and introduce reference counting for CPU ports and
DSA links using the same data structures as we have for MDB entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA treats some bridge FDB entries by trapping them to the CPU port.
Currently, the only class of such entries are FDB addresses learnt by
the software bridge on a foreign interface. However there are many more
to be added:
- FDB entries with the is_local flag (for termination) added by the
bridge on the user ports (typically containing the MAC address of the
bridge port)
- FDB entries pointing towards the bridge net device (for termination).
Typically these contain the MAC address of the bridge net device.
- Static FDB entries installed on a foreign interface that is in the
same bridge with a DSA user port.
The reason why a separate cross-chip notifier for host FDBs is justified
compared to normal FDBs is the same as in the case of host MDBs: the
cross-chip notifier matching function in switch.c should avoid
installing these entries on routing ports that route towards the
targeted switch, but not towards the CPU. This is required in order to
have proper support for H-like multi-chip topologies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since the cross-chip notifiers were introduced, the design was
meant to be simplistic and just get the job done without worrying too
much about dangling resources left behind.
For example, somebody installs an MDB entry on sw0p0 in this daisy chain
topology. It gets installed using ds->ops->port_mdb_add() on sw0p0,
sw1p4 and sw2p4.
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Then the same person deletes that MDB entry. The cross-chip notifier for
deletion only matches sw0p0:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
Why?
Because the DSA links are 'trunk' ports, if we just go ahead and delete
the MDB from sw1p4 and sw2p4 directly, we might delete those multicast
entries when they are still needed. Just consider the fact that somebody
does:
- add a multicast MAC address towards sw0p0 [ via the cross-chip
notifiers it gets installed on the DSA links too ]
- add the same multicast MAC address towards sw0p1 (another port of that
same switch)
- delete the same multicast MAC address from sw0p0.
At this point, if we deleted the MAC address from the DSA links, it
would be flooded, even though there is still an entry on switch 0 which
needs it not to.
So that is why deletions only match the targeted source port and nothing
on DSA links. Of course, dangling resources means that the hardware
tables will eventually run out given enough additions/removals, but hey,
at least it's simple.
But there is a bigger concern which needs to be addressed, and that is
our support for SWITCHDEV_OBJ_ID_HOST_MDB. DSA simply translates such an
object into a dsa_port_host_mdb_add() which ends up as ds->ops->port_mdb_add()
on the upstream port, and a similar thing happens on deletion:
dsa_port_host_mdb_del() will trigger ds->ops->port_mdb_del() on the
upstream port.
When there are 2 VLAN-unaware bridges spanning the same switch (which is
a use case DSA proudly supports), each bridge will install its own
SWITCHDEV_OBJ_ID_HOST_MDB entries. But upon deletion, DSA goes ahead and
emits a DSA_NOTIFIER_MDB_DEL for dp->cpu_dp, which is shared between the
user ports enslaved to br0 and the user ports enslaved to br1. Not good.
The host-trapped multicast addresses installed by br1 will be deleted
when any state changes in br0 (IGMP timers expire, or ports leave, etc).
To avoid this, we could of course go the route of the zero-sum game and
delete the DSA_NOTIFIER_MDB_DEL call for dp->cpu_dp. But the better
design is to just admit that on shared ports like DSA links and CPU
ports, we should be reference counting calls, even if this consumes some
dynamic memory which DSA has traditionally avoided. On the flip side,
the hardware tables of switches are limited in size, so it would be good
if the OS managed them properly instead of having them eventually
overflow.
To address the memory usage concern, we only apply the refcounting of
MDB entries on ports that are really shared (CPU ports and DSA links)
and not on user ports. In a typical single-switch setup, this means only
the CPU port (and the host MDB entries are not that many, really).
The name of the newly introduced data structures (dsa_mac_addr) is
chosen in such a way that will be reusable for host FDB entries (next
patch).
With this change, we can finally have the same matching logic for the
MDB additions and deletions, as well as for their host-trapped variants.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abd49535c3 ("net: dsa: execute dsa_switch_mdb_add only for
routing port in cross-chip topologies") does a surprisingly good job
even for the SWITCHDEV_OBJ_ID_HOST_MDB use case, where DSA simply
translates a switchdev object received on dp into a cross-chip notifier
for dp->cpu_dp.
To visualize how that works, imagine the daisy chain topology below and
consider a SWITCHDEV_OBJ_ID_HOST_MDB object emitted on sw2p0. How does
the cross-chip notifier know to match on all the right ports (sw0p4, the
dedicated CPU port, sw1p4, an upstream DSA link, and sw2p4, another
upstream DSA link)?
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
The answer is simple: the dedicated CPU port of sw2p0 is sw0p4, and
dsa_routing_port returns the upstream port for all switches.
That is fine, but there are other topologies where this does not work as
well. There are trees with "H" topologies in the wild, where there are 2
or more switches with DSA links between them, but every switch has its
dedicated CPU port. For these topologies, it seems stupid for the neighbor
switches to install an MDB entry on the routing port, since these
multicast addresses are fundamentally different than the usual ones we
support (and that is the justification for this patch, to introduce the
concept of a termination plane multicast MAC address, as opposed to a
forwarding plane multicast MAC address).
For example, when a SWITCHDEV_OBJ_ID_HOST_MDB would get added to sw0p0,
without this patch, it would get treated as a regular port MDB on sw0p2
and it would match on the ports below (including the sw1p3 routing port).
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ x ] [ ] [ ] [ ]
With the patch, the host MDB notifier on sw0p0 matches only on the local
switch, which is what we want for a termination plane address.
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ ] [ ] [ ] [ ]
Name this new matching function "dsa_switch_host_address_match" since we
will be reusing it soon for host FDB entries as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add reference counting for FDB entries in cross-chip
topologies, and in order for that to have any chance of working and not
be unbalanced (leading to entries which are never deleted), we need to
ensure that higher layers are sane, because if they aren't, it's garbage
in, garbage out.
For example, if we add a bridge FDB entry twice, the bridge properly
errors out:
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
RTNETLINK answers: File exists
However, the same thing cannot be said about the bridge bypass
operations:
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ echo $?
0
But one 'bridge fdb del' is enough to remove the entry, no matter how
many times it was added.
The bridge bypass operations are impossible to maintain in these
circumstances and lack of support for reference counting the cross-chip
notifiers is holding us back from making further progress, so just drop
support for them. The only way left for users to install static bridge
FDB entries is the proper one, using the "master static" flags.
With this change, rtnl_fdb_add() falls back to calling
ndo_dflt_fdb_add() which uses the duplicate-exclusive variant of
dev_uc_add(): dev_uc_add_excl(). Because DSA does not (yet) declare
IFF_UNICAST_FLT, this results in us going to promiscuous mode:
$ bridge fdb add dev swp0 00:01:02:03:04:05
[ 28.206743] device swp0 entered promiscuous mode
$ bridge fdb add dev swp0 00:01:02:03:04:05
RTNETLINK answers: File exists
So even if it does not completely fail, there is at least some indication
that it is behaving differently from before, and closer to user space
expectations, I would argue (the lack of a "local|static" specifier
defaults to "local", or "host-only", so dev_uc_add() is a reasonable
default implementation). If the generic implementation of .ndo_fdb_add
provided by Vlad Yasevich is a proof of anything, it only proves that
the implementation provided by DSA was always wrong, by not looking at
"ndm->ndm_state & NUD_NOARP" (the "static" flag which means that the FDB
entry points outwards) and "ndm->ndm_state & NUD_PERMANENT" (the "local"
flag which means that the FDB entry points towards the host). It all
used to mean the same thing to DSA.
Update the documentation so that the users are not confused about what's
going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch port leaves a bonding interface that is under a
bridge, there might be dangling switchdev objects on that port left
behind, because the bridge is not aware that its lower interface (the
bond) changed state in any way.
Call the bridge replay helpers with adding=false before changing
dp->bridge_dev to NULL, because we need to simulate to
dsa_slave_port_obj_del() that these notifications were emitted by the
bridge.
We add this hook to the NETDEV_PRECHANGEUPPER event handler, because
we are calling into switchdev (and the __switchdev_handle_port_obj_del
fanout helpers expect the upper/lower adjacency lists to still be valid)
and PRECHANGEUPPER is the last moment in time when they still are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to add more logic to the DSA NETDEV_PRECHANGEUPPER event
handler, more exactly we need to request an unsync of switchdev objects.
In order to fit more code, refactor the existing logic into a helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port leaves a LAG that is a bridge port, the switchdev
objects and port attributes offloaded to that port are not removed:
ip link add br0 type bridge
ip link add bond0 type bond mode 802.3ad
ip link set swp0 master bond0
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 nomaster
VLAN 100 will remain installed on swp0 despite it going into standalone
mode, because as far as the bridge is concerned, nothing ever happened
to its bridge port.
Let's extend the bridge vlan, fdb and mdb replay functions to take a
'bool adding' argument, and make DSA and ocelot call the replay
functions with 'adding' as false from the switchdev unsync path, for the
switch port that leaves the bridge.
Note that this patch in itself does not salvage anything, because in the
current pull mode of operation, DSA still needs to call the replay
helpers with adding=false. This will be done in another patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a slight inconvenience in the switchdev replay helpers added
recently, and this is when:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 master bond0
ip link set swp1 master bond0
Since the underlying driver (currently only DSA) asks for a replay of
VLANs when swp0 and swp1 join the LAG because it is bridged, what will
happen is that DSA will try to react twice on the VLAN event for swp0.
This is not really a huge problem right now, because most drivers accept
duplicates since the bridge itself does, but it will become a problem
when we add support for replaying switchdev object deletions.
Let's fix this by adding a blank void *ctx in the replay helpers, which
will be passed on by the bridge in the switchdev notifications. If the
context is NULL, everything is the same as before. But if the context is
populated with a valid pointer, the underlying switchdev driver
(currently DSA) can use the pointer to 'see through' the bridge port
(which in the example above is bond0) and 'know' that the event is only
for a particular physical port offloading that bridge port, and not for
all of them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MRP hardware assist being supported only by the ocelot switch
family, which by design does not support cross-chip bridging, the
current match functions are at best a guess and have not been confirmed
in any way to do anything relevant in a multi-switch topology.
Drop the code and make the notifiers match only on the targeted switch
port.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_change_mtu() calls dsa_port_mtu_change() twice:
- it sends a cross-chip notifier with the MTU of the CPU port which is
used to update the DSA links.
- it sends one targeted MTU notifier which is supposed to only match the
user port on which we are changing the MTU. The "propagate_upstream"
variable is used here to bypass the cross-chip notifier system from
switch.c
But due to a mistake, the second, targeted notifier matches not only on
the user port, but also on the DSA link which is a member of the same
switch, if that exists.
And because the DSA links of the entire dst were programmed in a
previous round to the largest_mtu via a "propagate_upstream == true"
notification, then the dsa_port_mtu_change(propagate_upstream == false)
call that is immediately upcoming will break the MTU on the one DSA link
which is chip-wise local to the dp whose MTU is changing right now.
Example given this daisy chain topology:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
ip link set sw0p1 mtu 9000
ip link set sw1p1 mtu 9000 # at this stage, sw0p1 and sw1p1 can talk
# to one another using jumbo frames
ip link set sw0p2 mtu 1500 # this programs the sw0p3 DSA link first to
# the largest_mtu of 9000, then reprograms it to
# 1500 with the "propagate_upstream == false"
# notifier, breaking communication between
# sw0p1 and sw1p1
To escape from this situation, make the targeted match really match on a
single port - the user port, and rename the "propagate_upstream"
variable to "targeted_match" to clarify the intention and avoid future
issues.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a cross-chip topology like this:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
and we issue the following commands:
1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600
we notice the following happening:
Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).
Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.
As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.
To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the notifier for adding a multicast MAC address matches on
the targeted port and on all DSA links in the system, be they upstream
or downstream links.
This leads to a considerable amount of useless traffic.
Consider this daisy chain topology, and a MDB add notifier emitted on
sw0p0. It matches on sw0p0, sw0p3, sw1p3 and sw2p4.
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ x ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
But switch 0 has no reason to send the multicast traffic for that MAC
address on sw0p3, which is how it reaches switches 1 and 2. Those
switches don't expect, according to the user configuration, to receive
this multicast address from switch 1, and they will drop it anyway,
because the only valid destination is the port they received it on.
They only need to configure themselves to deliver that multicast address
_towards_ switch 1, where the MDB entry is installed.
Similarly, switch 1 should not send this multicast traffic towards
sw1p3, because that is how it reaches switch 2.
With this change, the heat map for this MDB notifier changes as follows:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Now the mdb notifier behaves the same as the fdb notifier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between dsa_is_user_port and dsa_port_is_user is that the
former needs to look up the list of ports of the DSA switch tree in
order to find the struct dsa_port, while the latter directly receives it
as an argument.
dsa_is_user_port is already in widespread use and has its place, so
there isn't any chance of converting all callers to a single form.
But being able to do:
dsa_port_is_user(dp)
instead of
dsa_is_user_port(dp->ds, dp->index)
is much more efficient too, especially when the "dp" comes from an
iterator over the DSA switch tree - this reduces the complexity from
quadratic to linear.
Move these helpers from dsa2.c to include/net/dsa.h so that others can
use them too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cross-chip notifiers work by comparing each ds->index against the
info->sw_index value from the notifier. The ds->index is retrieved from
the device tree dsa,member property.
If a single tree cross-chip topology does not declare unique switch IDs,
this will result in hard-to-debug issues/voodoo effects such as the
cross-chip notifier for one switch port also matching the port with the
same number from another switch.
Check in dsa_switch_parse_member_of() whether the DSA switch tree
contains a DSA switch with the index we're preparing to add, before
actually adding it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current get_phy_flags() is only processed when we connect to a PHY
via a designed phy-handle property via phylink_of_phy_connect(), but if
we fallback on the internal MDIO bus created by a switch and take the
dsa_slave_phy_connect() path then we would not be processing that flag
and using it at PHY connection time.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamping procedure for SJA1105 is a bit unconventional
because the transmit procedure itself is unconventional.
Control packets (and therefore PTP as well) are transmitted to a
specific port in SJA1105 using "management routes" which must be written
over SPI to the switch. These are one-shot rules that match by
destination MAC address on traffic coming from the CPU port, and select
the precise destination port for that packet. So to transmit a packet
from NET_TX softirq context, we actually need to defer to a process
context so that we can perform that SPI write before we send the packet.
The DSA master dev_queue_xmit() runs in process context, and we poll
until the switch confirms it took the TX timestamp, then we annotate the
skb clone with that TX timestamp. This is why the sja1105 driver does
not need an skb queue for TX timestamping.
But the SJA1110 is a bit (not much!) more conventional, and you can
request 2-step TX timestamping through the DSA header, as well as give
the switch a cookie (timestamp ID) which it will give back to you when
it has the timestamp. So now we do need a queue for keeping the skb
clones until their TX timestamps become available.
The interesting part is that the metadata frames from SJA1105 haven't
disappeared completely. On SJA1105 they were used as follow-ups which
contained RX timestamps, but on SJA1110 they are actually TX completion
packets, which contain a variable (up to 32) array of timestamps.
Why an array? Because:
- not only is the TX timestamp on the egress port being communicated,
but also the RX timestamp on the CPU port. Nice, but we don't care
about that, so we ignore it.
- because a packet could be multicast to multiple egress ports, each
port takes its own timestamp, and the TX completion packet contains
the individual timestamps on each port.
This is unconventional because switches typically have a timestamping
FIFO and raise an interrupt, but this one doesn't. So the tagger needs
to detect and parse meta frames, and call into the main switch driver,
which pairs the timestamps with the skbs in the TX timestamping queue
which are waiting for one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has improved a few things compared to SJA1105:
- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.
- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.
- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.
But it also aggravated a few things:
- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.
- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:
* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set
So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:
- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.
So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.
On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.
Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.
On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.
The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).
Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105, RX timestamps for packets sent to the CPU are transmitted in
separate follow-up packets (metadata frames). These contain partial
timestamps (24 or 32 bits) which are kept in SJA1105_SKB_CB(skb)->meta_tstamp.
Thankfully, SJA1110 improved that, and the RX timestamps are now
transmitted in-band with the actual packet, in the timestamp trailer.
The RX timestamps are now full-width 64 bits.
Because we process the RX DSA tags in the rcv() method in the tagger,
but we would like to preserve the DSA code structure in that we populate
the skb timestamp in the port_rxtstamp() call which only happens later,
the implication is that we must somehow pass the 64-bit timestamp from
the rcv() method all the way to port_rxtstamp(). We can use the skb->cb
for that.
Rename the meta_tstamp from struct sja1105_skb_cb from "meta_tstamp" to
"tstamp", and increase its size to 64 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The added value of this function is that it can deal with both the case
where the VLAN header is in the skb head, as well as in the offload field.
This is something I was not able to do using other functions in the
network stack.
Since both ocelot-8021q and sja1105 need to do the same stuff, let's
make it a common service provided by tag_8021q.
This is done as refactoring for the new SJA1110 tagger, which partly
uses tag_8021q as well (just like SJA1105), and will be the third caller.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes no sense and is not needed, it is probably a debugging
leftover.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some really really weird switches just couldn't decide whether to use a
normal or a tail tagger, so they just did both.
This creates problems for DSA, because we only have the concept of an
'overhead' which can be applied to the headroom or to the tailroom of
the skb (like for example during the central TX reallocation procedure),
depending on the value of bool tail_tag, but not to both.
We need to generalize DSA to cater for these odd switches by
transforming the 'overhead / tail_tag' pair into 'needed_headroom /
needed_tailroom'.
The DSA master's MTU is increased to account for both.
The flow dissector code is modified such that it only calls the DSA
adjustment callback if the tagger has a non-zero header length.
Taggers are trivially modified to declare either needed_headroom or
needed_tailroom, based on the tail_tag value that they currently
declare.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using sub-VLANs in the range of 1-7, the resulting value from:
rx_vid = dsa_8021q_rx_vid_subvlan(ds, port, subvlan);
is wrong according to the description from tag_8021q.c:
| 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+-----------+-----+-----------------+-----------+-----------------------+
| DIR | SVL | SWITCH_ID | SUBVLAN | PORT |
+-----------+-----+-----------------+-----------+-----------------------+
For example, when ds->index == 0, port == 3 and subvlan == 1,
dsa_8021q_rx_vid_subvlan() returns 1027, same as it returns for
subvlan == 0, but it should have returned 1043.
This is because the low portion of the subvlan bits are not masked
properly when writing into the 12-bit VLAN value. They are masked into
bits 4:3, but they should be masked into bits 5:4.
Fixes: 3eaae1d05f ("net: dsa: tag_8021q: support up to 8 VLANs per port using sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements a bunch of 'standardized' ethtool statistics counters,
namely tx_packets, tx_bytes, rx_packets, rx_bytes. So whatever the
hardware driver returns in .get_sset_count(), we need to add 4 to that.
That is ok, except that .get_sset_count() can return a negative error
code, for example:
b53_get_sset_count
-> phy_ethtool_get_sset_count
-> return -EIO
-EIO is -5, and with 4 added to it, it becomes -1, aka -EPERM. One can
imagine that certain error codes may even become positive, although
based on code inspection I did not see instances of that.
Check the error code first, if it is negative return it as-is.
Based on a similar patch for dsa_master_get_strings from Dan Carpenter:
https://patchwork.kernel.org/project/netdevbpf/patch/YJaSe3RPgn7gKxZv@mwanda/
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ds->ops->get_sset_count() fails then it "count" is a negative error
code such as -EOPNOTSUPP. Because "i" is an unsigned int, the negative
error code is type promoted to a very high value and the loop will
corrupt memory until the system crashes.
Fix this by checking for error codes and changing the type of "i" to
just int.
Fixes: badf3ada60 ("net: dsa: Provide CPU port statistics to master netdev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case ethernet driver is enabled and INET is disabled, selftest will
fail to build.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 3e1e58d64c ("net: add generic selftest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428130947.29649-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a waste to clone skb directly in dsa_skb_tx_timestamp().
For one-step timestamping, a clone was not needed. For any failure of
port_txtstamp (this may usually happen), the skb clone had to be freed.
So this patch moves skb cloning for tx timestamp out of dsa core, and
let drivers clone skb in port_txtstamp if they really need.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ptp_classify_raw out of dsa core driver for handling tx
timestamp request. Let device drivers do this if they want.
Not all drivers want to limit tx timestamping for only PTP
packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx timestamp request in core driver at very beginning of
dsa_skb_tx_timestamp(), so that most skbs not requiring tx
timestamp just return. And drop such checking in device drivers.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
