mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-21 03:33:59 +08:00
fedd383e33
On a resume, when the power is lost during hibernate, the USB core will call hub_reset_resume for the xHCI USB 2.0 roothub, but not for the USB 3.0 roothub: [ 164.748310] usb usb1: root hub lost power or was reset [ 164.748353] usb usb2: root hub lost power or was reset [ 164.748487] usb usb3: root hub lost power or was reset [ 164.748488] xhci_hcd 0000:01:00.0: Stop HCD ... [ 164.870039] hub 4-0:1.0: hub_resume ... [ 164.870054] hub 3-0:1.0: hub_reset_resume This causes issues later, because the USB core assumes the USB 3.0 hub attached to the USB 3.0 roothub is still active. It attempts to queue a control URB for the external hub, which fails because all the device slot contexts were released when the USB 3.0 roothub lost power: [ 164.980044] hub 4-1:1.0: hub_resume [ 164.980047] xhci_hcd 0000:01:00.0: Get port status returned 0x10101 [ 164.980049] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980053] hub 3-0:1.0: port 1: status 0101 change 0001 [ 164.980056] hub 4-1:1.0: hub_port_status failed (err = -22) [ 164.980060] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc90008948440, 32'h202e1, 4'hf); [ 164.980062] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980066] xhci_hcd 0000:01:00.0: clear port connect change, actual port 0 status = 0x2e1 [ 164.980069] hub 4-1:1.0: hub_port_status failed (err = -22) [ 164.980072] xhci_hcd 0000:01:00.0: get port status, actual port 1 status = 0x2a0 [ 164.980074] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980077] xhci_hcd 0000:01:00.0: Get port status returned 0x100 [ 164.980079] hub 4-1:1.0: hub_port_status failed (err = -22) [ 164.980082] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980085] hub 4-1:1.0: hub_port_status failed (err = -22) [ 164.980088] hub 4-1:1.0: port 4: status 0000 change 0000 [ 164.980091] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980094] hub 4-1:1.0: activate --> -22 [ 164.980113] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980117] hub 4-1:1.0: hub_port_status failed (err = -22) [ 164.980119] xHCI xhci_urb_enqueue called with unaddressed device [ 164.980123] hub 4-1:1.0: can't resume port 4, status -22 [ 164.980126] hub 4-1:1.0: port 4 status ffff.ffff after resume, -22 [ 164.980129] usb 4-1.4: can't resume, status -22 [ 164.980131] hub 4-1:1.0: logical disconnect on port 4 This causes issues when a USB 3.0 hard drive is attached to the external USB 3.0 hub when the system is hibernated: [ 6249.849653] sd 8:0:0:0: [sdb] Unhandled error code [ 6249.849659] sd 8:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 6249.849663] sd 8:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 2a 08 00 00 02 00 [ 6249.849671] end_request: I/O error, dev sdb, sector 10760 Make sure to inform the USB core that *both* xHCI roothubs lost power. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> |
||
|---|---|---|
| .. | ||
| accessibility | ||
| acpi | ||
| amba | ||
| ata | ||
| atm | ||
| auxdisplay | ||
| base | ||
| block | ||
| bluetooth | ||
| cdrom | ||
| char | ||
| clk | ||
| clocksource | ||
| connector | ||
| cpufreq | ||
| cpuidle | ||
| crypto | ||
| dca | ||
| dio | ||
| dma | ||
| edac | ||
| eisa | ||
| firewire | ||
| firmware | ||
| gpio | ||
| gpu | ||
| hid | ||
| hwmon | ||
| hwspinlock | ||
| i2c | ||
| ide | ||
| idle | ||
| ieee802154 | ||
| infiniband | ||
| input | ||
| isdn | ||
| leds | ||
| lguest | ||
| macintosh | ||
| mca | ||
| md | ||
| media | ||
| memstick | ||
| message | ||
| mfd | ||
| misc | ||
| mmc | ||
| mtd | ||
| net | ||
| nfc | ||
| nubus | ||
| of | ||
| oprofile | ||
| parisc | ||
| parport | ||
| pci | ||
| pcmcia | ||
| platform | ||
| pnp | ||
| power | ||
| pps | ||
| ps3 | ||
| rapidio | ||
| regulator | ||
| rtc | ||
| s390 | ||
| sbus | ||
| scsi | ||
| sfi | ||
| sh | ||
| sn | ||
| spi | ||
| ssb | ||
| staging | ||
| target | ||
| tc | ||
| telephony | ||
| thermal | ||
| tty | ||
| uio | ||
| usb | ||
| uwb | ||
| vhost | ||
| video | ||
| virtio | ||
| vlynq | ||
| w1 | ||
| watchdog | ||
| xen | ||
| zorro | ||
| Kconfig | ||
| Makefile | ||