2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-25 05:34:00 +08:00
linux-next/drivers/media/dvb/cinergyT2/Kconfig
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

86 lines
2.8 KiB
Plaintext

config DVB_CINERGYT2
tristate "Terratec CinergyT2/qanu USB2 DVB-T receiver"
depends on DVB_CORE && USB
help
Support for "TerraTec CinergyT2" USB2.0 Highspeed DVB Receivers
Say Y if you own such a device and want to use it.
config DVB_CINERGYT2_TUNING
bool "sophisticated fine-tuning for CinergyT2 cards"
depends on DVB_CINERGYT2
help
Here you can fine-tune some parameters of the CinergyT2 driver.
Normally you don't need to touch this, but in exotic setups you
may fine-tune your setup and adjust e.g. DMA buffer sizes for
a particular application.
config DVB_CINERGYT2_STREAM_URB_COUNT
int "Number of queued USB Request Blocks for Highspeed Stream Transfers"
depends on DVB_CINERGYT2_TUNING
default "32"
help
USB Request Blocks for Highspeed Stream transfers are scheduled in
a queue for the Host Controller.
Usually the default value is a safe choice.
You may increase this number if you are using this device in a
Server Environment with many high-traffic USB Highspeed devices
sharing the same USB bus.
config DVB_CINERGYT2_STREAM_BUF_SIZE
int "Size of URB Stream Buffers for Highspeed Transfers"
depends on DVB_CINERGYT2_TUNING
default "512"
help
Should be a multiple of native buffer size of 512 bytes.
Default value is a safe choice.
You may increase this number if you are using this device in a
Server Environment with many high-traffic USB Highspeed devices
sharing the same USB bus.
config DVB_CINERGYT2_QUERY_INTERVAL
int "Status update interval [milliseconds]"
depends on DVB_CINERGYT2_TUNING
default "250"
help
This is the interval for status readouts from the demodulator.
You may try lower values if you need more responsive signal quality
measurements.
Please keep in mind that these updates cause traffic on the tuner
control bus and thus may or may not affect receiption sensitivity.
The default value should be a safe choice for common applications.
config DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE
bool "Register the onboard IR Remote Control Receiver as Input Device"
depends on DVB_CINERGYT2_TUNING
default "yes"
help
Enable this option if you want to use the onboard Infrared Remote
Control Receiver as Linux-Input device.
Right now only the keycode table for the default Remote Control
delivered with the device is supported, please see the driver
source code to find out how to add support for other controls.
config DVB_CINERGYT2_RC_QUERY_INTERVAL
int "Infrared Remote Controller update interval [milliseconds]"
depends on DVB_CINERGYT2_TUNING && DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE
default "100"
help
If you have a very fast-repeating remote control you can try lower
values, for normal consumer receivers the default value should be
a safe choice.