mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 20:53:53 +08:00
53f4035282
The compatible value shouldn't include ".txt", which was probably cut and paste from the filename. Reported-by: Domenico Andreoli <cavokz@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Olof Johansson <olof@lixom.net>
111 lines
1.9 KiB
Plaintext
111 lines
1.9 KiB
Plaintext
BCM2835 Top-Level ("ARMCTRL") Interrupt Controller
|
|
|
|
The BCM2835 contains a custom top-level interrupt controller, which supports
|
|
72 interrupt sources using a 2-level register scheme. The interrupt
|
|
controller, or the HW block containing it, is referred to occasionally
|
|
as "armctrl" in the SoC documentation, hence naming of this binding.
|
|
|
|
Required properties:
|
|
|
|
- compatible : should be "brcm,bcm2835-armctrl-ic"
|
|
- reg : Specifies base physical address and size of the registers.
|
|
- interrupt-controller : Identifies the node as an interrupt controller
|
|
- #interrupt-cells : Specifies the number of cells needed to encode an
|
|
interrupt source. The value shall be 2.
|
|
|
|
The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic
|
|
pending" register, or 1/2 respectively for interrupts in the "IRQ pending
|
|
1/2" register.
|
|
|
|
The 2nd cell contains the interrupt number within the bank. Valid values
|
|
are 0..7 for bank 0, and 0..31 for bank 1.
|
|
|
|
The interrupt sources are as follows:
|
|
|
|
Bank 0:
|
|
0: ARM_TIMER
|
|
1: ARM_MAILBOX
|
|
2: ARM_DOORBELL_0
|
|
3: ARM_DOORBELL_1
|
|
4: VPU0_HALTED
|
|
5: VPU1_HALTED
|
|
6: ILLEGAL_TYPE0
|
|
7: ILLEGAL_TYPE1
|
|
|
|
Bank 1:
|
|
0: TIMER0
|
|
1: TIMER1
|
|
2: TIMER2
|
|
3: TIMER3
|
|
4: CODEC0
|
|
5: CODEC1
|
|
6: CODEC2
|
|
7: VC_JPEG
|
|
8: ISP
|
|
9: VC_USB
|
|
10: VC_3D
|
|
11: TRANSPOSER
|
|
12: MULTICORESYNC0
|
|
13: MULTICORESYNC1
|
|
14: MULTICORESYNC2
|
|
15: MULTICORESYNC3
|
|
16: DMA0
|
|
17: DMA1
|
|
18: VC_DMA2
|
|
19: VC_DMA3
|
|
20: DMA4
|
|
21: DMA5
|
|
22: DMA6
|
|
23: DMA7
|
|
24: DMA8
|
|
25: DMA9
|
|
26: DMA10
|
|
27: DMA11
|
|
28: DMA12
|
|
29: AUX
|
|
30: ARM
|
|
31: VPUDMA
|
|
|
|
Bank 2:
|
|
0: HOSTPORT
|
|
1: VIDEOSCALER
|
|
2: CCP2TX
|
|
3: SDC
|
|
4: DSI0
|
|
5: AVE
|
|
6: CAM0
|
|
7: CAM1
|
|
8: HDMI0
|
|
9: HDMI1
|
|
10: PIXELVALVE1
|
|
11: I2CSPISLV
|
|
12: DSI1
|
|
13: PWA0
|
|
14: PWA1
|
|
15: CPR
|
|
16: SMI
|
|
17: GPIO0
|
|
18: GPIO1
|
|
19: GPIO2
|
|
20: GPIO3
|
|
21: VC_I2C
|
|
22: VC_SPI
|
|
23: VC_I2SPCM
|
|
24: VC_SDIO
|
|
25: VC_UART
|
|
26: SLIMBUS
|
|
27: VEC
|
|
28: CPG
|
|
29: RNG
|
|
30: VC_ARASANSDIO
|
|
31: AVSPMON
|
|
|
|
Example:
|
|
|
|
intc: interrupt-controller {
|
|
compatible = "brcm,bcm2835-armctrl-ic";
|
|
reg = <0x7e00b200 0x200>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|