renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-15 16:53:54 +08:00
Code
f78e3d407a
linux-next/drivers/cxl/cxlmem.h
Ben Widawsky 8dd2bc0f8e cxl/mem: Add the cxl_mem driver 
At this point the subsystem can enumerate all CXL ports (CXL.mem decode
resources in upstream switch ports and host bridges) in a system. The
last mile is connecting those ports to endpoints.

The cxl_mem driver connects an endpoint device to the platform CXL.mem
protoctol decode-topology. At ->probe() time it walks its
device-topology-ancestry and adds a CXL Port object at every Upstream
Port hop until it gets to CXL root. The CXL root object is only present
after a platform firmware driver registers platform CXL resources. For
ACPI based platform this is managed by the ACPI0017 device and the
cxl_acpi driver.

The ports are registered such that disabling a given port automatically
unregisters all descendant ports, and the chain can only be registered
after the root is established.

Given ACPI device scanning may run asynchronously compared to PCI device
scanning the root driver is tasked with rescanning the bus after the
root successfully probes.

Conversely if any ports in a chain between the root and an endpoint
becomes disconnected it subsequently triggers the endpoint to
unregister. Given lock depenedencies the endpoint unregistration happens
in a workqueue asynchronously. If userspace cares about synchronizing
delayed work after port events the /sys/bus/cxl/flush attribute is
available for that purpose.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[djbw: clarify changelog, rework hotplug support]
Link: https://lore.kernel.org/r/164398782997.903003.9725273241627693186.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2022-02-08 22:57:32 -08:00

307 lines
10 KiB
C
Raw Blame History

/* SPDX-License-Identifier: GPL-2.0-only */
/* Copyright(c) 2020-2021 Intel Corporation. */
#ifndef __CXL_MEM_H__
#define __CXL_MEM_H__
#include <uapi/linux/cxl_mem.h>
#include <linux/cdev.h>
#include "cxl.h"
/* CXL 2.0 8.2.8.5.1.1 Memory Device Status Register */
#define CXLMDEV_STATUS_OFFSET 0x0
#define CXLMDEV_DEV_FATAL BIT(0)
#define CXLMDEV_FW_HALT BIT(1)
#define CXLMDEV_STATUS_MEDIA_STATUS_MASK GENMASK(3, 2)
#define CXLMDEV_MS_NOT_READY 0
#define CXLMDEV_MS_READY 1
#define CXLMDEV_MS_ERROR 2
#define CXLMDEV_MS_DISABLED 3
#define CXLMDEV_READY(status) \
(FIELD_GET(CXLMDEV_STATUS_MEDIA_STATUS_MASK, status) == \
CXLMDEV_MS_READY)
#define CXLMDEV_MBOX_IF_READY BIT(4)
#define CXLMDEV_RESET_NEEDED_MASK GENMASK(7, 5)
#define CXLMDEV_RESET_NEEDED_NOT 0
#define CXLMDEV_RESET_NEEDED_COLD 1
#define CXLMDEV_RESET_NEEDED_WARM 2
#define CXLMDEV_RESET_NEEDED_HOT 3
#define CXLMDEV_RESET_NEEDED_CXL 4
#define CXLMDEV_RESET_NEEDED(status) \
(FIELD_GET(CXLMDEV_RESET_NEEDED_MASK, status) != \
CXLMDEV_RESET_NEEDED_NOT)
/**
* struct cxl_memdev - CXL bus object representing a Type-3 Memory Device
* @dev: driver core device object
* @cdev: char dev core object for ioctl operations
* @cxlds: The device state backing this device
* @detach_work: active memdev lost a port in its ancestry
* @id: id number of this memdev instance.
*/
struct cxl_memdev {
struct device dev;
struct cdev cdev;
struct cxl_dev_state *cxlds;
struct work_struct detach_work;
int id;
};
static inline struct cxl_memdev *to_cxl_memdev(struct device *dev)
{
return container_of(dev, struct cxl_memdev, dev);
}
bool is_cxl_memdev(struct device *dev);
static inline bool is_cxl_endpoint(struct cxl_port *port)
{
return is_cxl_memdev(port->uport);
}
struct cxl_memdev *devm_cxl_add_memdev(struct cxl_dev_state *cxlds);
/**
* struct cxl_mbox_cmd - A command to be submitted to hardware.
* @opcode: (input) The command set and command submitted to hardware.
* @payload_in: (input) Pointer to the input payload.
* @payload_out: (output) Pointer to the output payload. Must be allocated by
* the caller.
* @size_in: (input) Number of bytes to load from @payload_in.
* @size_out: (input) Max number of bytes loaded into @payload_out.
* (output) Number of bytes generated by the device. For fixed size
* outputs commands this is always expected to be deterministic. For
* variable sized output commands, it tells the exact number of bytes
* written.
* @return_code: (output) Error code returned from hardware.
*
* This is the primary mechanism used to send commands to the hardware.
* All the fields except @payload_* correspond exactly to the fields described in
* Command Register section of the CXL 2.0 8.2.8.4.5. @payload_in and
* @payload_out are written to, and read from the Command Payload Registers
* defined in CXL 2.0 8.2.8.4.8.
*/
struct cxl_mbox_cmd {
u16 opcode;
void *payload_in;
void *payload_out;
size_t size_in;
size_t size_out;
u16 return_code;
#define CXL_MBOX_SUCCESS 0
};
/*
* CXL 2.0 - Memory capacity multiplier
* See Section 8.2.9.5
*
* Volatile, Persistent, and Partition capacities are specified to be in
* multiples of 256MB - define a multiplier to convert to/from bytes.
*/
#define CXL_CAPACITY_MULTIPLIER SZ_256M
/**
* struct cxl_endpoint_dvsec_info - Cached DVSEC info
* @mem_enabled: cached value of mem_enabled in the DVSEC, PCIE_DEVICE
* @ranges: Number of active HDM ranges this device uses.
* @dvsec_range: cached attributes of the ranges in the DVSEC, PCIE_DEVICE
*/
struct cxl_endpoint_dvsec_info {
bool mem_enabled;
int ranges;
struct range dvsec_range[2];
};
/**
* struct cxl_dev_state - The driver device state
*
* cxl_dev_state represents the CXL driver/device state. It provides an
* interface to mailbox commands as well as some cached data about the device.
* Currently only memory devices are represented.
*
* @dev: The device associated with this CXL state
* @regs: Parsed register blocks
* @cxl_dvsec: Offset to the PCIe device DVSEC
* @payload_size: Size of space for payload
* (CXL 2.0 8.2.8.4.3 Mailbox Capabilities Register)
* @lsa_size: Size of Label Storage Area
* (CXL 2.0 8.2.9.5.1.1 Identify Memory Device)
* @mbox_mutex: Mutex to synchronize mailbox access.
* @firmware_version: Firmware version for the memory device.
* @enabled_cmds: Hardware commands found enabled in CEL.
* @exclusive_cmds: Commands that are kernel-internal only
* @pmem_range: Active Persistent memory capacity configuration
* @ram_range: Active Volatile memory capacity configuration
* @total_bytes: sum of all possible capacities
* @volatile_only_bytes: hard volatile capacity
* @persistent_only_bytes: hard persistent capacity
* @partition_align_bytes: alignment size for partition-able capacity
* @active_volatile_bytes: sum of hard + soft volatile
* @active_persistent_bytes: sum of hard + soft persistent
* @next_volatile_bytes: volatile capacity change pending device reset
* @next_persistent_bytes: persistent capacity change pending device reset
* @component_reg_phys: register base of component registers
* @info: Cached DVSEC information about the device.
* @serial: PCIe Device Serial Number
* @mbox_send: @dev specific transport for transmitting mailbox commands
* @wait_media_ready: @dev specific method to await media ready
*
* See section 8.2.9.5.2 Capacity Configuration and Label Storage for
* details on capacity parameters.
*/
struct cxl_dev_state {
struct device *dev;
struct cxl_regs regs;
int cxl_dvsec;
size_t payload_size;
size_t lsa_size;
struct mutex mbox_mutex; /* Protects device mailbox and firmware */
char firmware_version[0x10];
DECLARE_BITMAP(enabled_cmds, CXL_MEM_COMMAND_ID_MAX);
DECLARE_BITMAP(exclusive_cmds, CXL_MEM_COMMAND_ID_MAX);
struct range pmem_range;
struct range ram_range;
u64 total_bytes;
u64 volatile_only_bytes;
u64 persistent_only_bytes;
u64 partition_align_bytes;
u64 active_volatile_bytes;
u64 active_persistent_bytes;
u64 next_volatile_bytes;
u64 next_persistent_bytes;
resource_size_t component_reg_phys;
struct cxl_endpoint_dvsec_info info;
u64 serial;
int (*mbox_send)(struct cxl_dev_state *cxlds, struct cxl_mbox_cmd *cmd);
int (*wait_media_ready)(struct cxl_dev_state *cxlds);
};
enum cxl_opcode {
CXL_MBOX_OP_INVALID = 0x0000,
CXL_MBOX_OP_RAW = CXL_MBOX_OP_INVALID,
CXL_MBOX_OP_GET_FW_INFO = 0x0200,
CXL_MBOX_OP_ACTIVATE_FW = 0x0202,
CXL_MBOX_OP_GET_SUPPORTED_LOGS = 0x0400,
CXL_MBOX_OP_GET_LOG = 0x0401,
CXL_MBOX_OP_IDENTIFY = 0x4000,
CXL_MBOX_OP_GET_PARTITION_INFO = 0x4100,
CXL_MBOX_OP_SET_PARTITION_INFO = 0x4101,
CXL_MBOX_OP_GET_LSA = 0x4102,
CXL_MBOX_OP_SET_LSA = 0x4103,
CXL_MBOX_OP_GET_HEALTH_INFO = 0x4200,
CXL_MBOX_OP_GET_ALERT_CONFIG = 0x4201,
CXL_MBOX_OP_SET_ALERT_CONFIG = 0x4202,
CXL_MBOX_OP_GET_SHUTDOWN_STATE = 0x4203,
CXL_MBOX_OP_SET_SHUTDOWN_STATE = 0x4204,
CXL_MBOX_OP_GET_POISON = 0x4300,
CXL_MBOX_OP_INJECT_POISON = 0x4301,
CXL_MBOX_OP_CLEAR_POISON = 0x4302,
CXL_MBOX_OP_GET_SCAN_MEDIA_CAPS = 0x4303,
CXL_MBOX_OP_SCAN_MEDIA = 0x4304,
CXL_MBOX_OP_GET_SCAN_MEDIA = 0x4305,
CXL_MBOX_OP_MAX = 0x10000
};
#define DEFINE_CXL_CEL_UUID \
UUID_INIT(0xda9c0b5, 0xbf41, 0x4b78, 0x8f, 0x79, 0x96, 0xb1, 0x62, \
0x3b, 0x3f, 0x17)
#define DEFINE_CXL_VENDOR_DEBUG_UUID \
UUID_INIT(0xe1819d9, 0x11a9, 0x400c, 0x81, 0x1f, 0xd6, 0x07, 0x19, \
0x40, 0x3d, 0x86)
struct cxl_mbox_get_supported_logs {
__le16 entries;
u8 rsvd[6];
struct cxl_gsl_entry {
uuid_t uuid;
__le32 size;
} __packed entry[];
} __packed;
struct cxl_cel_entry {
__le16 opcode;
__le16 effect;
} __packed;
struct cxl_mbox_get_log {
uuid_t uuid;
__le32 offset;
__le32 length;
} __packed;
/* See CXL 2.0 Table 175 Identify Memory Device Output Payload */
struct cxl_mbox_identify {
char fw_revision[0x10];
__le64 total_capacity;
__le64 volatile_capacity;
__le64 persistent_capacity;
__le64 partition_align;
__le16 info_event_log_size;
__le16 warning_event_log_size;
__le16 failure_event_log_size;
__le16 fatal_event_log_size;
__le32 lsa_size;
u8 poison_list_max_mer[3];
__le16 inject_poison_limit;
u8 poison_caps;
u8 qos_telemetry_caps;
} __packed;
struct cxl_mbox_get_lsa {
u32 offset;
u32 length;
} __packed;
struct cxl_mbox_set_lsa {
u32 offset;
u32 reserved;
u8 data[];
} __packed;
/**
* struct cxl_mem_command - Driver representation of a memory device command
* @info: Command information as it exists for the UAPI
* @opcode: The actual bits used for the mailbox protocol
* @flags: Set of flags effecting driver behavior.
*
* * %CXL_CMD_FLAG_FORCE_ENABLE: In cases of error, commands with this flag
* will be enabled by the driver regardless of what hardware may have
* advertised.
*
* The cxl_mem_command is the driver's internal representation of commands that
* are supported by the driver. Some of these commands may not be supported by
* the hardware. The driver will use @info to validate the fields passed in by
* the user then submit the @opcode to the hardware.
*
* See struct cxl_command_info.
*/
struct cxl_mem_command {
struct cxl_command_info info;
enum cxl_opcode opcode;
u32 flags;
#define CXL_CMD_FLAG_NONE 0
#define CXL_CMD_FLAG_FORCE_ENABLE BIT(0)
};
int cxl_mbox_send_cmd(struct cxl_dev_state *cxlds, u16 opcode, void *in,
size_t in_size, void *out, size_t out_size);
int cxl_dev_state_identify(struct cxl_dev_state *cxlds);
int cxl_enumerate_cmds(struct cxl_dev_state *cxlds);
int cxl_mem_create_range_info(struct cxl_dev_state *cxlds);
struct cxl_dev_state *cxl_dev_state_create(struct device *dev);
void set_exclusive_cxl_commands(struct cxl_dev_state *cxlds, unsigned long *cmds);
void clear_exclusive_cxl_commands(struct cxl_dev_state *cxlds, unsigned long *cmds);
struct cxl_hdm {
struct cxl_component_regs regs;
unsigned int decoder_count;
unsigned int target_count;
unsigned int interleave_mask;
struct cxl_port *port;
};
#endif /* __CXL_MEM_H__ */
View Git Blame Copy Permalink