mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-25 05:34:00 +08:00
c06cd9bfca
Add support for Iomega Iconnect system. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-By: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
166 lines
3.5 KiB
C
166 lines
3.5 KiB
C
/*
|
|
* arch/arm/mach-kirkwood/board-iconnect.c
|
|
*
|
|
* Iomega i-connect Board Setup
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/of_fdt.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/of_platform.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/mv643xx_eth.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/spi/flash.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/orion_spi.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/input.h>
|
|
#include <linux/gpio_keys.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <mach/kirkwood.h>
|
|
#include "common.h"
|
|
#include "mpp.h"
|
|
|
|
static struct mv643xx_eth_platform_data iconnect_ge00_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_ADDR(11),
|
|
};
|
|
|
|
static struct gpio_led iconnect_led_pins[] = {
|
|
{
|
|
.name = "led_level",
|
|
.gpio = 41,
|
|
.default_trigger = "default-on",
|
|
}, {
|
|
.name = "power:blue",
|
|
.gpio = 42,
|
|
.default_trigger = "timer",
|
|
}, {
|
|
.name = "power:red",
|
|
.gpio = 43,
|
|
}, {
|
|
.name = "usb1:blue",
|
|
.gpio = 44,
|
|
}, {
|
|
.name = "usb2:blue",
|
|
.gpio = 45,
|
|
}, {
|
|
.name = "usb3:blue",
|
|
.gpio = 46,
|
|
}, {
|
|
.name = "usb4:blue",
|
|
.gpio = 47,
|
|
}, {
|
|
.name = "otb:blue",
|
|
.gpio = 48,
|
|
},
|
|
};
|
|
|
|
static struct gpio_led_platform_data iconnect_led_data = {
|
|
.leds = iconnect_led_pins,
|
|
.num_leds = ARRAY_SIZE(iconnect_led_pins),
|
|
.gpio_blink_set = orion_gpio_led_blink_set,
|
|
};
|
|
|
|
static struct platform_device iconnect_leds = {
|
|
.name = "leds-gpio",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &iconnect_led_data,
|
|
}
|
|
};
|
|
|
|
static unsigned int iconnect_mpp_config[] __initdata = {
|
|
MPP12_GPIO,
|
|
MPP35_GPIO,
|
|
MPP41_GPIO,
|
|
MPP42_GPIO,
|
|
MPP43_GPIO,
|
|
MPP44_GPIO,
|
|
MPP45_GPIO,
|
|
MPP46_GPIO,
|
|
MPP47_GPIO,
|
|
MPP48_GPIO,
|
|
0
|
|
};
|
|
|
|
static struct i2c_board_info __initdata iconnect_board_info[] = {
|
|
{
|
|
I2C_BOARD_INFO("lm63", 0x4c),
|
|
},
|
|
};
|
|
|
|
static struct mtd_partition iconnect_nand_parts[] = {
|
|
{
|
|
.name = "flash",
|
|
.offset = 0,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
/* yikes... theses are the original input buttons */
|
|
/* but I'm not convinced by the sw event choices */
|
|
static struct gpio_keys_button iconnect_buttons[] = {
|
|
{
|
|
.type = EV_SW,
|
|
.code = SW_LID,
|
|
.gpio = 12,
|
|
.desc = "Reset Button",
|
|
.active_low = 1,
|
|
.debounce_interval = 100,
|
|
}, {
|
|
.type = EV_SW,
|
|
.code = SW_TABLET_MODE,
|
|
.gpio = 35,
|
|
.desc = "OTB Button",
|
|
.active_low = 1,
|
|
.debounce_interval = 100,
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_platform_data iconnect_button_data = {
|
|
.buttons = iconnect_buttons,
|
|
.nbuttons = ARRAY_SIZE(iconnect_buttons),
|
|
};
|
|
|
|
static struct platform_device iconnect_button_device = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.num_resources = 0,
|
|
.dev = {
|
|
.platform_data = &iconnect_button_data,
|
|
},
|
|
};
|
|
|
|
void __init iconnect_init(void)
|
|
{
|
|
kirkwood_mpp_conf(iconnect_mpp_config);
|
|
kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
|
|
kirkwood_i2c_init();
|
|
i2c_register_board_info(0, iconnect_board_info,
|
|
ARRAY_SIZE(iconnect_board_info));
|
|
|
|
kirkwood_ehci_init();
|
|
kirkwood_ge00_init(&iconnect_ge00_data);
|
|
|
|
platform_device_register(&iconnect_button_device);
|
|
platform_device_register(&iconnect_leds);
|
|
}
|
|
|
|
static int __init iconnect_pci_init(void)
|
|
{
|
|
if (of_machine_is_compatible("iom,iconnect"))
|
|
kirkwood_pcie_init(KW_PCIE0);
|
|
return 0;
|
|
}
|
|
subsys_initcall(iconnect_pci_init);
|