mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-24 21:24:00 +08:00
5a29f7893f
I've hit an issue on my system when I've been using RealTek RTL8139D cards in bonding interface in mode balancing-alb. When I enslave a card, the current active slave (bond->curr_active_slave) is not set and the link is therefore not functional. ---- # cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008) Bonding Mode: adaptive load balancing Primary Slave: None Currently Active Slave: None MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:1f:1f:01:2f:22 ---- The thing that gets it right is when I unplug the cable and then I put it back into the NIC. Then the current active slave is set to eth1 and link is working just fine. Here is dmesg log with bonding DEBUG messages turned on: ---- ADDRCONF(NETDEV_UP): bond0: link is not ready event_dev: bond0, event: 1 IFF_MASTER event_dev: bond0, event: 8 IFF_MASTER bond_ioctl: master=bond0, cmd=35216 slave_dev=cac5d800: slave_dev->name=eth1: eth1: ! NETIF_F_VLAN_CHALLENGED event_dev: eth1, event: 8 eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 event_dev: eth1, event: 1 event_dev: eth1, event: 8 IFF_SLAVE Initial state of slave_dev is BOND_LINK_UP bonding: bond0: enslaving eth1 as an active interface with an up link. ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready event_dev: bond0, event: 4 IFF_MASTER bond0: no IPv6 routers present <<<<cable unplug>>>> eth1: link down event_dev: eth1, event: 4 IFF_SLAVE bonding: bond0: link status definitely down for interface eth1, disabling it event_dev: bond0, event: 4 IFF_MASTER <<<<cable plug>>>> eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 event_dev: eth1, event: 4 IFF_SLAVE bonding: bond0: link status definitely up for interface eth1. bonding: bond0: making interface eth1 the new active one. event_dev: eth1, event: 8 IFF_SLAVE event_dev: eth1, event: 8 IFF_SLAVE bonding: bond0: first active interface up! event_dev: bond0, event: 4 IFF_MASTER ---- The current active slave is set by calling bond_select_active_slave() function from bond_miimon_commit() function when the slave (eth1) link goes to state up. I also tested this on other machine with Broadcom NetXtreme II BCM5708 1000Base-T NIC and there all works fine. The thing is that this adapter is down and goes up after few seconds after it is enslaved. This patch calls bond_select_active_slave() in bond_enslave() function for modes alb and tlb and makes sure that the current active slave is set up properly even when the slave state is already up. Tested on both systems, works fine. Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to test that. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|---|---|---|
| .. | ||
| bond_3ad.c | ||
| bond_3ad.h | ||
| bond_alb.c | ||
| bond_alb.h | ||
| bond_ipv6.c | ||
| bond_main.c | ||
| bond_sysfs.c | ||
| bonding.h | ||
| Makefile | ||