mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 06:34:11 +08:00
7f4da4745c
Hp is providing a Hardware WatchDog Timer driver that will only work with the specific HW Timer located in the HP ProLiant iLO 2 ASIC. The iLO 2 HW Timer will generate a Non-maskable Interrupt (NMI) 9 seconds before physically resetting the server, by removing power, so that the event can be logged to the HP Integrated Management Log (IML), a Non-Volatile Random Access Memory (NVRAM). The logging of the event is performed using the HP ProLiant ROM via an Industry Standard access known as a BIOS Service Directory Entry. Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
915 lines
29 KiB
Plaintext
915 lines
29 KiB
Plaintext
#
|
|
# Watchdog device configuration
|
|
#
|
|
|
|
menuconfig WATCHDOG
|
|
bool "Watchdog Timer Support"
|
|
---help---
|
|
If you say Y here (and to one of the following options) and create a
|
|
character special file /dev/watchdog with major number 10 and minor
|
|
number 130 using mknod ("man mknod"), you will get a watchdog, i.e.:
|
|
subsequently opening the file and then failing to write to it for
|
|
longer than 1 minute will result in rebooting the machine. This
|
|
could be useful for a networked machine that needs to come back
|
|
on-line as fast as possible after a lock-up. There's both a watchdog
|
|
implementation entirely in software (which can sometimes fail to
|
|
reboot the machine) and a driver for hardware watchdog boards, which
|
|
are more robust and can also keep track of the temperature inside
|
|
your computer. For details, read
|
|
<file:Documentation/watchdog/watchdog-api.txt> in the kernel source.
|
|
|
|
The watchdog is usually used together with the watchdog daemon
|
|
which is available from
|
|
<ftp://ibiblio.org/pub/Linux/system/daemons/watchdog/>. This daemon can
|
|
also monitor NFS connections and can reboot the machine when the process
|
|
table is full.
|
|
|
|
If unsure, say N.
|
|
|
|
if WATCHDOG
|
|
|
|
config WATCHDOG_NOWAYOUT
|
|
bool "Disable watchdog shutdown on close"
|
|
help
|
|
The default watchdog behaviour (which you get if you say N here) is
|
|
to stop the timer if the process managing it closes the file
|
|
/dev/watchdog. It's always remotely possible that this process might
|
|
get killed. If you say Y here, the watchdog cannot be stopped once
|
|
it has been started.
|
|
|
|
#
|
|
# General Watchdog drivers
|
|
#
|
|
|
|
comment "Watchdog Device Drivers"
|
|
|
|
# Architecture Independent
|
|
|
|
config SOFT_WATCHDOG
|
|
tristate "Software watchdog"
|
|
help
|
|
A software monitoring watchdog. This will fail to reboot your system
|
|
from some situations that the hardware watchdog will recover
|
|
from. Equally it's a lot cheaper to install.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called softdog.
|
|
|
|
# ALPHA Architecture
|
|
|
|
# ARM Architecture
|
|
|
|
config AT91RM9200_WATCHDOG
|
|
tristate "AT91RM9200 watchdog"
|
|
depends on ARCH_AT91RM9200
|
|
help
|
|
Watchdog timer embedded into AT91RM9200 chips. This will reboot your
|
|
system when the timeout is reached.
|
|
|
|
config 21285_WATCHDOG
|
|
tristate "DC21285 watchdog"
|
|
depends on FOOTBRIDGE
|
|
help
|
|
The Intel Footbridge chip contains a built-in watchdog circuit. Say Y
|
|
here if you wish to use this. Alternatively say M to compile the
|
|
driver as a module, which will be called wdt285.
|
|
|
|
This driver does not work on all machines. In particular, early CATS
|
|
boards have hardware problems that will cause the machine to simply
|
|
lock up if the watchdog fires.
|
|
|
|
"If in doubt, leave it out" - say N.
|
|
|
|
config 977_WATCHDOG
|
|
tristate "NetWinder WB83C977 watchdog"
|
|
depends on FOOTBRIDGE && ARCH_NETWINDER
|
|
help
|
|
Say Y here to include support for the WB977 watchdog included in
|
|
NetWinder machines. Alternatively say M to compile the driver as
|
|
a module, which will be called wdt977.
|
|
|
|
Not sure? It's safe to say N.
|
|
|
|
config IXP2000_WATCHDOG
|
|
tristate "IXP2000 Watchdog"
|
|
depends on ARCH_IXP2000
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Intel IXP2000(2400, 2800, 2850) network processors.
|
|
This driver can be built as a module by choosing M. The module
|
|
will be called ixp2000_wdt.
|
|
|
|
Say N if you are unsure.
|
|
|
|
config IXP4XX_WATCHDOG
|
|
tristate "IXP4xx Watchdog"
|
|
depends on ARCH_IXP4XX
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Intel IXP4xx network processors. This driver can
|
|
be built as a module by choosing M. The module will
|
|
be called ixp4xx_wdt.
|
|
|
|
Note: The internal IXP4xx watchdog does a soft CPU reset
|
|
which doesn't reset any peripherals. There are circumstances
|
|
where the watchdog will fail to reset the board correctly
|
|
(e.g., if the boot ROM is in an unreadable state).
|
|
|
|
Say N if you are unsure.
|
|
|
|
config KS8695_WATCHDOG
|
|
tristate "KS8695 watchdog"
|
|
depends on ARCH_KS8695
|
|
help
|
|
Watchdog timer embedded into KS8695 processor. This will reboot your
|
|
system when the timeout is reached.
|
|
|
|
config S3C2410_WATCHDOG
|
|
tristate "S3C2410 Watchdog"
|
|
depends on ARCH_S3C2410
|
|
help
|
|
Watchdog timer block in the Samsung S3C2410 chips. This will
|
|
reboot the system when the timer expires with the watchdog
|
|
enabled.
|
|
|
|
The driver is limited by the speed of the system's PCLK
|
|
signal, so with reasonably fast systems (PCLK around 50-66MHz)
|
|
then watchdog intervals of over approximately 20seconds are
|
|
unavailable.
|
|
|
|
The driver can be built as a module by choosing M, and will
|
|
be called s3c2410_wdt
|
|
|
|
config SA1100_WATCHDOG
|
|
tristate "SA1100/PXA2xx watchdog"
|
|
depends on ARCH_SA1100 || ARCH_PXA
|
|
help
|
|
Watchdog timer embedded into SA11x0 and PXA2xx chips. This will
|
|
reboot your system when timeout is reached.
|
|
|
|
NOTE: once enabled, this timer cannot be disabled.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sa1100_wdt.
|
|
|
|
config MPCORE_WATCHDOG
|
|
tristate "MPcore watchdog"
|
|
depends on ARM_MPCORE_PLATFORM && LOCAL_TIMERS
|
|
help
|
|
Watchdog timer embedded into the MPcore system.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mpcore_wdt.
|
|
|
|
config EP93XX_WATCHDOG
|
|
tristate "EP93xx Watchdog"
|
|
depends on ARCH_EP93XX
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
embedded in the Cirrus Logic EP93xx family of devices.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ep93xx_wdt.
|
|
|
|
config OMAP_WATCHDOG
|
|
tristate "OMAP Watchdog"
|
|
depends on ARCH_OMAP16XX || ARCH_OMAP24XX
|
|
help
|
|
Support for TI OMAP1610/OMAP1710/OMAP2420 watchdog. Say 'Y' here to
|
|
enable the OMAP1610/OMAP1710 watchdog timer.
|
|
|
|
config PNX4008_WATCHDOG
|
|
tristate "PNX4008 Watchdog"
|
|
depends on ARCH_PNX4008
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the PNX4008 processor.
|
|
This driver can be built as a module by choosing M. The module
|
|
will be called pnx4008_wdt.
|
|
|
|
Say N if you are unsure.
|
|
|
|
config IOP_WATCHDOG
|
|
tristate "IOP Watchdog"
|
|
depends on PLAT_IOP
|
|
select WATCHDOG_NOWAYOUT if (ARCH_IOP32X || ARCH_IOP33X)
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Intel IOP3XX & IOP13XX I/O Processors. This driver can
|
|
be built as a module by choosing M. The module will
|
|
be called iop_wdt.
|
|
|
|
Note: The IOP13XX watchdog does an Internal Bus Reset which will
|
|
affect both cores and the peripherals of the IOP. The ATU-X
|
|
and/or ATUe configuration registers will remain intact, but if
|
|
operating as an Root Complex and/or Central Resource, the PCI-X
|
|
and/or PCIe busses will also be reset. THIS IS A VERY BIG HAMMER.
|
|
|
|
config DAVINCI_WATCHDOG
|
|
tristate "DaVinci watchdog"
|
|
depends on ARCH_DAVINCI
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the DaVinci DM644x/DM646x processors.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called davinci_wdt.
|
|
|
|
NOTE: once enabled, this timer cannot be disabled.
|
|
Say N if you are unsure.
|
|
|
|
# ARM26 Architecture
|
|
|
|
# AVR32 Architecture
|
|
|
|
config AT32AP700X_WDT
|
|
tristate "AT32AP700x watchdog"
|
|
depends on CPU_AT32AP700X
|
|
help
|
|
Watchdog timer embedded into AT32AP700x devices. This will reboot
|
|
your system when the timeout is reached.
|
|
|
|
# BLACKFIN Architecture
|
|
|
|
config BFIN_WDT
|
|
tristate "Blackfin On-Chip Watchdog Timer"
|
|
depends on BLACKFIN
|
|
---help---
|
|
If you say yes here you will get support for the Blackfin On-Chip
|
|
Watchdog Timer. If you have one of these processors and wish to
|
|
have watchdog support enabled, say Y, otherwise say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called bfin_wdt.
|
|
|
|
# CRIS Architecture
|
|
|
|
# FRV Architecture
|
|
|
|
# H8300 Architecture
|
|
|
|
# X86 (i386 + ia64 + x86_64) Architecture
|
|
|
|
config ACQUIRE_WDT
|
|
tristate "Acquire SBC Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on Single Board
|
|
Computers produced by Acquire Inc (and others). This watchdog
|
|
simply watches your kernel to make sure it doesn't freeze, and if
|
|
it does, it reboots your computer after a certain amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called acquirewdt.
|
|
|
|
Most people will say N.
|
|
|
|
config ADVANTECH_WDT
|
|
tristate "Advantech SBC Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
If you are configuring a Linux kernel for the Advantech single-board
|
|
computer, say `Y' here to support its built-in watchdog timer
|
|
feature. More information can be found at
|
|
<http://www.advantech.com.tw/products/>
|
|
|
|
config ALIM1535_WDT
|
|
tristate "ALi M1535 PMU Watchdog Timer"
|
|
depends on X86 && PCI
|
|
---help---
|
|
This is the driver for the hardware watchdog on the ALi M1535 PMU.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called alim1535_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config ALIM7101_WDT
|
|
tristate "ALi M7101 PMU Computer Watchdog"
|
|
depends on X86 && PCI
|
|
help
|
|
This is the driver for the hardware watchdog on the ALi M7101 PMU
|
|
as used in the x86 Cobalt servers.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called alim7101_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config SC520_WDT
|
|
tristate "AMD Elan SC520 processor Watchdog"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog built in to the
|
|
AMD "Elan" SC520 microcomputer commonly used in embedded systems.
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called sc520_wdt.
|
|
|
|
config EUROTECH_WDT
|
|
tristate "Eurotech CPU-1220/1410 Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
Enable support for the watchdog timer on the Eurotech CPU-1220 and
|
|
CPU-1410 cards. These are PC/104 SBCs. Spec sheets and product
|
|
information are at <http://www.eurotech.it/>.
|
|
|
|
config IB700_WDT
|
|
tristate "IB700 SBC Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the IB700 Single
|
|
Board Computer produced by TMC Technology (www.tmc-uk.com). This watchdog
|
|
simply watches your kernel to make sure it doesn't freeze, and if
|
|
it does, it reboots your computer after a certain amount of time.
|
|
|
|
This driver is like the WDT501 driver but for slightly different hardware.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ib700wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config IBMASR
|
|
tristate "IBM Automatic Server Restart"
|
|
depends on X86
|
|
help
|
|
This is the driver for the IBM Automatic Server Restart watchdog
|
|
timer built-in into some eServer xSeries machines.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ibmasr.
|
|
|
|
config WAFER_WDT
|
|
tristate "ICP Single Board Computer Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is a driver for the hardware watchdog on the ICP Single
|
|
Board Computer. This driver is working on (at least) the following
|
|
IPC SBC's: Wafer 5823, Rocky 4783, Rocky 3703 and Rocky 3782.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wafer5823wdt.
|
|
|
|
config I6300ESB_WDT
|
|
tristate "Intel 6300ESB Timer/Watchdog"
|
|
depends on X86 && PCI
|
|
---help---
|
|
Hardware driver for the watchdog timer built into the Intel
|
|
6300ESB controller hub.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called i6300esb.
|
|
|
|
config ITCO_WDT
|
|
tristate "Intel TCO Timer/Watchdog"
|
|
depends on (X86 || IA64) && PCI
|
|
---help---
|
|
Hardware driver for the intel TCO timer based watchdog devices.
|
|
These drivers are included in the Intel 82801 I/O Controller
|
|
Hub family (from ICH0 up to ICH8) and in the Intel 6300ESB
|
|
controller hub.
|
|
|
|
The TCO (Total Cost of Ownership) timer is a watchdog timer
|
|
that will reboot the machine after its second expiration. The
|
|
expiration time can be configured with the "heartbeat" parameter.
|
|
|
|
On some motherboards the driver may fail to reset the chipset's
|
|
NO_REBOOT flag which prevents the watchdog from rebooting the
|
|
machine. If this is the case you will get a kernel message like
|
|
"failed to reset NO_REBOOT flag, reboot disabled by hardware".
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called iTCO_wdt.
|
|
|
|
config ITCO_VENDOR_SUPPORT
|
|
bool "Intel TCO Timer/Watchdog Specific Vendor Support"
|
|
depends on ITCO_WDT
|
|
---help---
|
|
Add vendor specific support to the intel TCO timer based watchdog
|
|
devices. At this moment we only have additional support for some
|
|
SuperMicro Inc. motherboards.
|
|
|
|
config IT8712F_WDT
|
|
tristate "IT8712F (Smart Guardian) Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the built-in watchdog timer on the IT8712F
|
|
Super I/0 chipset used on many motherboards.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called it8712f_wdt.
|
|
|
|
config HP_WATCHDOG
|
|
tristate "HP Proliant iLO 2 Hardware Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
A software monitoring watchdog and NMI sourcing driver. This driver
|
|
will detect lockups and provide stack trace. Also, when an NMI
|
|
occurs this driver will make the necessary BIOS calls to log
|
|
the cause of the NMI. This is a driver that will only load on a
|
|
HP ProLiant system with a minimum of iLO2 support.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called hpwdt.
|
|
|
|
config SC1200_WDT
|
|
tristate "National Semiconductor PC87307/PC97307 (ala SC1200) Watchdog"
|
|
depends on X86
|
|
help
|
|
This is a driver for National Semiconductor PC87307/PC97307 hardware
|
|
watchdog cards as found on the SC1200. This watchdog is mainly used
|
|
for power management purposes and can be used to power down the device
|
|
during inactivity periods (includes interrupt activity monitoring).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sc1200wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config SCx200_WDT
|
|
tristate "National Semiconductor SCx200 Watchdog"
|
|
depends on SCx200 && PCI
|
|
help
|
|
Enable the built-in watchdog timer support on the National
|
|
Semiconductor SCx200 processors.
|
|
|
|
If compiled as a module, it will be called scx200_wdt.
|
|
|
|
config PC87413_WDT
|
|
tristate "NS PC87413 watchdog"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the PC87413 chipset
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pc87413_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config 60XX_WDT
|
|
tristate "SBC-60XX Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This driver can be used with the watchdog timer found on some
|
|
single board computers, namely the 6010 PII based computer.
|
|
It may well work with other cards. It reads port 0x443 to enable
|
|
and re-set the watchdog timer, and reads port 0x45 to disable
|
|
the watchdog. If you have a card that behave in similar ways,
|
|
you can probably make this driver work with your card as well.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called sbc60xxwdt.
|
|
|
|
config SBC8360_WDT
|
|
tristate "SBC8360 Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
|
|
This is the driver for the hardware watchdog on the SBC8360 Single
|
|
Board Computer produced by Axiomtek Co., Ltd. (www.axiomtek.com).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc8360.ko.
|
|
|
|
Most people will say N.
|
|
|
|
config SBC7240_WDT
|
|
tristate "SBC Nano 7240 Watchdog Timer"
|
|
depends on X86_32
|
|
---help---
|
|
This is the driver for the hardware watchdog found on the IEI
|
|
single board computers EPIC Nano 7240 (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc7240_wdt.
|
|
|
|
config CPU5_WDT
|
|
tristate "SMA CPU5 Watchdog"
|
|
depends on X86
|
|
---help---
|
|
TBD.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cpu5wdt.
|
|
|
|
config SMSC37B787_WDT
|
|
tristate "Winbond SMsC37B787 Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog component on the
|
|
Winbond SMsC37B787 chipset as used on the NetRunner Mainboard
|
|
from Vision Systems and maybe others.
|
|
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
Usually a userspace daemon will notify the kernel WDT driver that
|
|
userspace is still alive, at regular intervals.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called smsc37b787_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83627HF_WDT
|
|
tristate "W83627HF Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the W83627HF chipset
|
|
as used in Advantech PC-9578 and Tyan S2721-533 motherboards
|
|
(and likely others). This watchdog simply watches your kernel to
|
|
make sure it doesn't freeze, and if it does, it reboots your computer
|
|
after a certain amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83627hf_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83697HF_WDT
|
|
tristate "W83697HF/W83697HG Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the W83697HF/HG
|
|
chipset as used in Dedibox/VIA motherboards (and likely others).
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83697hf_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83877F_WDT
|
|
tristate "W83877F (EMACS) Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the W83877F chipset
|
|
as used in EMACS PC-104 motherboards (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83877f_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83977F_WDT
|
|
tristate "W83977F (PCM-5335) Watchdog Timer"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the hardware watchdog on the W83977F I/O chip
|
|
as used in AAEON's PCM-5335 SBC (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83977f_wdt.
|
|
|
|
config MACHZ_WDT
|
|
tristate "ZF MachZ Watchdog"
|
|
depends on X86
|
|
---help---
|
|
If you are using a ZF Micro MachZ processor, say Y here, otherwise
|
|
N. This is the driver for the watchdog timer built-in on that
|
|
processor using ZF-Logic interface. This watchdog simply watches
|
|
your kernel to make sure it doesn't freeze, and if it does, it
|
|
reboots your computer after a certain amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called machzwd.
|
|
|
|
config SBC_EPX_C3_WATCHDOG
|
|
tristate "Winsystems SBC EPX-C3 watchdog"
|
|
depends on X86
|
|
---help---
|
|
This is the driver for the built-in watchdog timer on the EPX-C3
|
|
Single-board computer made by Winsystems, Inc.
|
|
|
|
*Note*: This hardware watchdog is not probeable and thus there
|
|
is no way to know if writing to its IO address will corrupt
|
|
your system or have any real effect. The only way to be sure
|
|
that this driver does what you want is to make sure you
|
|
are running it on an EPX-C3 from Winsystems with the watchdog
|
|
timer at IO address 0x1ee and 0x1ef. It will write to both those
|
|
IO ports. Basically, the assumption is made that if you compile
|
|
this driver into your kernel and/or load it as a module, that you
|
|
know what you are doing and that you are in fact running on an
|
|
EPX-C3 board!
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc_epx_c3.
|
|
|
|
# M32R Architecture
|
|
|
|
# M68K Architecture
|
|
|
|
# M68KNOMMU Architecture
|
|
|
|
# MIPS Architecture
|
|
|
|
config INDYDOG
|
|
tristate "Indy/I2 Hardware Watchdog"
|
|
depends on SGI_HAS_INDYDOG
|
|
help
|
|
Hardware driver for the Indy's/I2's watchdog. This is a
|
|
watchdog timer that will reboot the machine after a 60 second
|
|
timer expired and no process has written to /dev/watchdog during
|
|
that time.
|
|
|
|
config WDT_MTX1
|
|
tristate "MTX-1 Hardware Watchdog"
|
|
depends on MIPS_MTX1
|
|
help
|
|
Hardware driver for the MTX-1 boards. This is a watchdog timer that
|
|
will reboot the machine after a 100 seconds timer expired.
|
|
|
|
config WDT_RM9K_GPI
|
|
tristate "RM9000/GPI hardware watchdog"
|
|
depends on CPU_RM9000
|
|
help
|
|
Watchdog implementation using the GPI hardware found on
|
|
PMC-Sierra RM9xxx CPUs.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called rm9k_wdt.
|
|
|
|
config SIBYTE_WDOG
|
|
tristate "Sibyte SoC hardware watchdog"
|
|
depends on CPU_SB1
|
|
help
|
|
Watchdog driver for the built in watchdog hardware in Sibyte
|
|
SoC processors. There are apparently two watchdog timers
|
|
on such processors; this driver supports only the first one,
|
|
because currently Linux only supports exporting one watchdog
|
|
to userspace.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called sb_wdog.
|
|
|
|
config AR7_WDT
|
|
tristate "TI AR7 Watchdog Timer"
|
|
depends on AR7
|
|
help
|
|
Hardware driver for the TI AR7 Watchdog Timer.
|
|
|
|
config TXX9_WDT
|
|
tristate "Toshiba TXx9 Watchdog Timer"
|
|
depends on CPU_TX39XX || CPU_TX49XX
|
|
help
|
|
Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
|
|
|
|
# PARISC Architecture
|
|
|
|
# POWERPC Architecture
|
|
|
|
config MPC5200_WDT
|
|
tristate "MPC5200 Watchdog Timer"
|
|
depends on PPC_MPC52xx
|
|
|
|
config 8xx_WDT
|
|
tristate "MPC8xx Watchdog Timer"
|
|
depends on 8xx
|
|
|
|
config 83xx_WDT
|
|
tristate "MPC83xx Watchdog Timer"
|
|
depends on PPC_83xx
|
|
|
|
config MV64X60_WDT
|
|
tristate "MV64X60 (Marvell Discovery) Watchdog Timer"
|
|
depends on MV64X60
|
|
|
|
config BOOKE_WDT
|
|
bool "PowerPC Book-E Watchdog Timer"
|
|
depends on BOOKE || 4xx
|
|
---help---
|
|
Please see Documentation/watchdog/watchdog-api.txt for
|
|
more information.
|
|
|
|
# PPC64 Architecture
|
|
|
|
config WATCHDOG_RTAS
|
|
tristate "RTAS watchdog"
|
|
depends on PPC_RTAS
|
|
help
|
|
This driver adds watchdog support for the RTAS watchdog.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called wdrtas.
|
|
|
|
# S390 Architecture
|
|
|
|
config ZVM_WATCHDOG
|
|
tristate "z/VM Watchdog Timer"
|
|
depends on S390
|
|
help
|
|
IBM s/390 and zSeries machines running under z/VM 5.1 or later
|
|
provide a virtual watchdog timer to their guest that cause a
|
|
user define Control Program command to be executed after a
|
|
timeout.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called vmwatchdog.
|
|
|
|
# SUPERH (sh + sh64) Architecture
|
|
|
|
config SH_WDT
|
|
tristate "SuperH Watchdog"
|
|
depends on SUPERH && (CPU_SH3 || CPU_SH4)
|
|
help
|
|
This driver adds watchdog support for the integrated watchdog in the
|
|
SuperH processors. If you have one of these processors and wish
|
|
to have watchdog support enabled, say Y, otherwise say N.
|
|
|
|
As a side note, saying Y here will automatically boost HZ to 1000
|
|
so that the timer has a chance to clear the overflow counter. On
|
|
slower systems (such as the SH-2 and SH-3) this will likely yield
|
|
some performance issues. As such, the WDT should be avoided here
|
|
unless it is absolutely necessary.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called shwdt.
|
|
|
|
config SH_WDT_MMAP
|
|
bool "Allow mmap of SH WDT"
|
|
default n
|
|
depends on SH_WDT
|
|
help
|
|
If you say Y here, user applications will be able to mmap the
|
|
WDT/CPG registers.
|
|
|
|
# SPARC Architecture
|
|
|
|
# SPARC64 Architecture
|
|
|
|
config WATCHDOG_CP1XXX
|
|
tristate "CP1XXX Hardware Watchdog support"
|
|
depends on SPARC64 && PCI
|
|
---help---
|
|
This is the driver for the hardware watchdog timers present on
|
|
Sun Microsystems CompactPCI models CP1400 and CP1500.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cpwatchdog.
|
|
|
|
If you do not have a CompactPCI model CP1400 or CP1500, or
|
|
another UltraSPARC-IIi-cEngine boardset with hardware watchdog,
|
|
you should say N to this option.
|
|
|
|
config WATCHDOG_RIO
|
|
tristate "RIO Hardware Watchdog support"
|
|
depends on SPARC64 && PCI
|
|
help
|
|
Say Y here to support the hardware watchdog capability on Sun RIO
|
|
machines. The watchdog timeout period is normally one minute but
|
|
can be changed with a boot-time parameter.
|
|
|
|
# V850 Architecture
|
|
|
|
# XTENSA Architecture
|
|
|
|
#
|
|
# ISA-based Watchdog Cards
|
|
#
|
|
|
|
comment "ISA-based Watchdog Cards"
|
|
depends on ISA
|
|
|
|
config PCWATCHDOG
|
|
tristate "Berkshire Products ISA-PC Watchdog"
|
|
depends on ISA
|
|
---help---
|
|
This is the driver for the Berkshire Products ISA-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. This driver is like the WDT501 driver but for different
|
|
hardware. Please read <file:Documentation/watchdog/pcwd-watchdog.txt>. The PC
|
|
watchdog cards can be ordered from <http://www.berkprod.com/>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd.
|
|
|
|
Most people will say N.
|
|
|
|
config MIXCOMWD
|
|
tristate "Mixcom Watchdog"
|
|
depends on ISA
|
|
---help---
|
|
This is a driver for the Mixcom hardware watchdog cards. This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mixcomwd.
|
|
|
|
Most people will say N.
|
|
|
|
config WDT
|
|
tristate "WDT Watchdog timer"
|
|
depends on ISA
|
|
---help---
|
|
If you have a WDT500P or WDT501P watchdog board, say Y here,
|
|
otherwise N. It is not possible to probe for this board, which means
|
|
that you have to inform the kernel about the IO port and IRQ that
|
|
is needed (you can do this via the io and irq parameters)
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wdt.
|
|
|
|
config WDT_501
|
|
bool "WDT501 features"
|
|
depends on WDT
|
|
help
|
|
Saying Y here and creating a character special file /dev/temperature
|
|
with major number 10 and minor number 131 ("man mknod") will give
|
|
you a thermometer inside your computer: reading from
|
|
/dev/temperature yields one byte, the temperature in degrees
|
|
Fahrenheit. This works only if you have a WDT501P watchdog board
|
|
installed.
|
|
|
|
If you want to enable the Fan Tachometer on the WDT501P, then you
|
|
can do this via the tachometer parameter. Only do this if you have a
|
|
fan tachometer actually set up.
|
|
|
|
#
|
|
# PCI-based Watchdog Cards
|
|
#
|
|
|
|
comment "PCI-based Watchdog Cards"
|
|
depends on PCI
|
|
|
|
config PCIPCWATCHDOG
|
|
tristate "Berkshire Products PCI-PC Watchdog"
|
|
depends on PCI
|
|
---help---
|
|
This is the driver for the Berkshire Products PCI-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. The card can also monitor the internal temperature of the PC.
|
|
More info is available at <http://www.berkprod.com/pci_pc_watchdog.htm>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd_pci.
|
|
|
|
Most people will say N.
|
|
|
|
config WDTPCI
|
|
tristate "PCI-WDT500/501 Watchdog timer"
|
|
depends on PCI
|
|
---help---
|
|
If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wdt_pci.
|
|
|
|
config WDT_501_PCI
|
|
bool "PCI-WDT501 features"
|
|
depends on WDTPCI
|
|
help
|
|
Saying Y here and creating a character special file /dev/temperature
|
|
with major number 10 and minor number 131 ("man mknod") will give
|
|
you a thermometer inside your computer: reading from
|
|
/dev/temperature yields one byte, the temperature in degrees
|
|
Fahrenheit. This works only if you have a PCI-WDT501 watchdog board
|
|
installed.
|
|
|
|
If you want to enable the Fan Tachometer on the PCI-WDT501, then you
|
|
can do this via the tachometer parameter. Only do this if you have a
|
|
fan tachometer actually set up.
|
|
|
|
#
|
|
# USB-based Watchdog Cards
|
|
#
|
|
|
|
comment "USB-based Watchdog Cards"
|
|
depends on USB
|
|
|
|
config USBPCWATCHDOG
|
|
tristate "Berkshire Products USB-PC Watchdog"
|
|
depends on USB
|
|
---help---
|
|
This is the driver for the Berkshire Products USB-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. The card can also monitor the internal temperature of the PC.
|
|
More info is available at <http://www.berkprod.com/usb_pc_watchdog.htm>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd_usb.
|
|
|
|
Most people will say N.
|
|
|
|
endif # WATCHDOG
|