renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-27 14:43:58 +08:00
Code
f472c0b59f
linux-next/Documentation/edac.txt
Mauro Carvalho Chehab 37e59f876b [media, edac] Change my email address 
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-02-07 08:03:07 -02:00

776 lines
24 KiB
Plaintext
Raw Blame History

EDAC - Error Detection And Correction
Written by Doug Thompson <dougthompson@xmission.com>
7 Dec 2005
17 Jul 2007 Updated
(c) Mauro Carvalho Chehab
05 Aug 2009 Nehalem interface
EDAC is maintained and written by:
Doug Thompson, Dave Jiang, Dave Peterson et al,
original author: Thayne Harbaugh,
Contact:
website: bluesmoke.sourceforge.net
mailing list: bluesmoke-devel@lists.sourceforge.net
"bluesmoke" was the name for this device driver when it was "out-of-tree"
and maintained at sourceforge.net. When it was pushed into 2.6.16 for the
first time, it was renamed to 'EDAC'.
The bluesmoke project at sourceforge.net is now utilized as a 'staging area'
for EDAC development, before it is sent upstream to kernel.org
At the bluesmoke/EDAC project site is a series of quilt patches against
recent kernels, stored in a SVN repository. For easier downloading, there
is also a tarball snapshot available.
============================================================================
EDAC PURPOSE
The 'edac' kernel module goal is to detect and report errors that occur
within the computer system running under linux.
MEMORY
In the initial release, memory Correctable Errors (CE) and Uncorrectable
Errors (UE) are the primary errors being harvested. These types of errors
are harvested by the 'edac_mc' class of device.
Detecting CE events, then harvesting those events and reporting them,
CAN be a predictor of future UE events. With CE events, the system can
continue to operate, but with less safety. Preventive maintenance and
proactive part replacement of memory DIMMs exhibiting CEs can reduce
the likelihood of the dreaded UE events and system 'panics'.
NON-MEMORY
A new feature for EDAC, the edac_device class of device, was added in
the 2.6.23 version of the kernel.
This new device type allows for non-memory type of ECC hardware detectors
to have their states harvested and presented to userspace via the sysfs
interface.
Some architectures have ECC detectors for L1, L2 and L3 caches, along with DMA
engines, fabric switches, main data path switches, interconnections,
and various other hardware data paths. If the hardware reports it, then
a edac_device device probably can be constructed to harvest and present
that to userspace.
PCI BUS SCANNING
In addition, PCI Bus Parity and SERR Errors are scanned for on PCI devices
in order to determine if errors are occurring on data transfers.
The presence of PCI Parity errors must be examined with a grain of salt.
There are several add-in adapters that do NOT follow the PCI specification
with regards to Parity generation and reporting. The specification says
the vendor should tie the parity status bits to 0 if they do not intend
to generate parity. Some vendors do not do this, and thus the parity bit
can "float" giving false positives.
In the kernel there is a PCI device attribute located in sysfs that is
checked by the EDAC PCI scanning code. If that attribute is set,
PCI parity/error scanning is skipped for that device. The attribute
is:
broken_parity_status
as is located in /sys/devices/pci<XXX>/0000:XX:YY.Z directories for
PCI devices.
FUTURE HARDWARE SCANNING
EDAC will have future error detectors that will be integrated with
EDAC or added to it, in the following list:
MCE Machine Check Exception
MCA Machine Check Architecture
NMI NMI notification of ECC errors
MSRs Machine Specific Register error cases
and other mechanisms.
These errors are usually bus errors, ECC errors, thermal throttling
and the like.
============================================================================
EDAC VERSIONING
EDAC is composed of a "core" module (edac_core.ko) and several Memory
Controller (MC) driver modules. On a given system, the CORE
is loaded and one MC driver will be loaded. Both the CORE and
the MC driver (or edac_device driver) have individual versions that reflect
current release level of their respective modules.
Thus, to "report" on what version a system is running, one must report both
the CORE's and the MC driver's versions.
LOADING
If 'edac' was statically linked with the kernel then no loading is
necessary. If 'edac' was built as modules then simply modprobe the
'edac' pieces that you need. You should be able to modprobe
hardware-specific modules and have the dependencies load the necessary core
modules.
Example:
$> modprobe amd76x_edac
loads both the amd76x_edac.ko memory controller module and the edac_mc.ko
core module.
============================================================================
EDAC sysfs INTERFACE
EDAC presents a 'sysfs' interface for control, reporting and attribute
reporting purposes.
EDAC lives in the /sys/devices/system/edac directory.
Within this directory there currently reside 2 'edac' components:
mc memory controller(s) system
pci PCI control and status system
============================================================================
Memory Controller (mc) Model
First a background on the memory controller's model abstracted in EDAC.
Each 'mc' device controls a set of DIMM memory modules. These modules are
laid out in a Chip-Select Row (csrowX) and Channel table (chX). There can
be multiple csrows and multiple channels.
Memory controllers allow for several csrows, with 8 csrows being a typical value.
Yet, the actual number of csrows depends on the electrical "loading"
of a given motherboard, memory controller and DIMM characteristics.
Dual channels allows for 128 bit data transfers to the CPU from memory.
Some newer chipsets allow for more than 2 channels, like Fully Buffered DIMMs
(FB-DIMMs). The following example will assume 2 channels:
Channel 0 Channel 1
===================================
csrow0 | DIMM_A0 | DIMM_B0 |
csrow1 | DIMM_A0 | DIMM_B0 |
===================================
===================================
csrow2 | DIMM_A1 | DIMM_B1 |
csrow3 | DIMM_A1 | DIMM_B1 |
===================================
In the above example table there are 4 physical slots on the motherboard
for memory DIMMs:
DIMM_A0
DIMM_B0
DIMM_A1
DIMM_B1
Labels for these slots are usually silk screened on the motherboard. Slots
labeled 'A' are channel 0 in this example. Slots labeled 'B'
are channel 1. Notice that there are two csrows possible on a
physical DIMM. These csrows are allocated their csrow assignment
based on the slot into which the memory DIMM is placed. Thus, when 1 DIMM
is placed in each Channel, the csrows cross both DIMMs.
Memory DIMMs come single or dual "ranked". A rank is a populated csrow.
Thus, 2 single ranked DIMMs, placed in slots DIMM_A0 and DIMM_B0 above
will have 1 csrow, csrow0. csrow1 will be empty. On the other hand,
when 2 dual ranked DIMMs are similarly placed, then both csrow0 and
csrow1 will be populated. The pattern repeats itself for csrow2 and
csrow3.
The representation of the above is reflected in the directory tree
in EDAC's sysfs interface. Starting in directory
/sys/devices/system/edac/mc each memory controller will be represented
by its own 'mcX' directory, where 'X' is the index of the MC.
..../edac/mc/
|
|->mc0
|->mc1
|->mc2
....
Under each 'mcX' directory each 'csrowX' is again represented by a
'csrowX', where 'X' is the csrow index:
.../mc/mc0/
|
|->csrow0
|->csrow2
|->csrow3
....
Notice that there is no csrow1, which indicates that csrow0 is
composed of a single ranked DIMMs. This should also apply in both
Channels, in order to have dual-channel mode be operational. Since
both csrow2 and csrow3 are populated, this indicates a dual ranked
set of DIMMs for channels 0 and 1.
Within each of the 'mcX' and 'csrowX' directories are several
EDAC control and attribute files.
============================================================================
'mcX' DIRECTORIES
In 'mcX' directories are EDAC control and attribute files for
this 'X' instance of the memory controllers.
For a description of the sysfs API, please see:
Documentation/ABI/testing/sysfs/devices-edac
============================================================================
'csrowX' DIRECTORIES
When CONFIG_EDAC_LEGACY_SYSFS is enabled, the sysfs will contain the
csrowX directories. As this API doesn't work properly for Rambus, FB-DIMMs
and modern Intel Memory Controllers, this is being deprecated in favor
of dimmX directories.
In the 'csrowX' directories are EDAC control and attribute files for
this 'X' instance of csrow:
Total Uncorrectable Errors count attribute file:
'ue_count'
This attribute file displays the total count of uncorrectable
errors that have occurred on this csrow. If panic_on_ue is set
this counter will not have a chance to increment, since EDAC
will panic the system.
Total Correctable Errors count attribute file:
'ce_count'
This attribute file displays the total count of correctable
errors that have occurred on this csrow. This
count is very important to examine. CEs provide early
indications that a DIMM is beginning to fail. This count
field should be monitored for non-zero values and report
such information to the system administrator.
Total memory managed by this csrow attribute file:
'size_mb'
This attribute file displays, in count of megabytes, of memory
that this csrow contains.
Memory Type attribute file:
'mem_type'
This attribute file will display what type of memory is currently
on this csrow. Normally, either buffered or unbuffered memory.
Examples:
Registered-DDR
Unbuffered-DDR
EDAC Mode of operation attribute file:
'edac_mode'
This attribute file will display what type of Error detection
and correction is being utilized.
Device type attribute file:
'dev_type'
This attribute file will display what type of DRAM device is
being utilized on this DIMM.
Examples:
x1
x2
x4
x8
Channel 0 CE Count attribute file:
'ch0_ce_count'
This attribute file will display the count of CEs on this
DIMM located in channel 0.
Channel 0 UE Count attribute file:
'ch0_ue_count'
This attribute file will display the count of UEs on this
DIMM located in channel 0.
Channel 0 DIMM Label control file:
'ch0_dimm_label'
This control file allows this DIMM to have a label assigned
to it. With this label in the module, when errors occur
the output can provide the DIMM label in the system log.
This becomes vital for panic events to isolate the
cause of the UE event.
DIMM Labels must be assigned after booting, with information
that correctly identifies the physical slot with its
silk screen label. This information is currently very
motherboard specific and determination of this information
must occur in userland at this time.
Channel 1 CE Count attribute file:
'ch1_ce_count'
This attribute file will display the count of CEs on this
DIMM located in channel 1.
Channel 1 UE Count attribute file:
'ch1_ue_count'
This attribute file will display the count of UEs on this
DIMM located in channel 0.
Channel 1 DIMM Label control file:
'ch1_dimm_label'
This control file allows this DIMM to have a label assigned
to it. With this label in the module, when errors occur
the output can provide the DIMM label in the system log.
This becomes vital for panic events to isolate the
cause of the UE event.
DIMM Labels must be assigned after booting, with information
that correctly identifies the physical slot with its
silk screen label. This information is currently very
motherboard specific and determination of this information
must occur in userland at this time.
============================================================================
SYSTEM LOGGING
If logging for UEs and CEs are enabled then system logs will have
error notices indicating errors that have been detected:
EDAC MC0: CE page 0x283, offset 0xce0, grain 8, syndrome 0x6ec3, row 0,
channel 1 "DIMM_B1": amd76x_edac
EDAC MC0: CE page 0x1e5, offset 0xfb0, grain 8, syndrome 0xb741, row 0,
channel 1 "DIMM_B1": amd76x_edac
The structure of the message is:
the memory controller (MC0)
Error type (CE)
memory page (0x283)
offset in the page (0xce0)
the byte granularity (grain 8)
or resolution of the error
the error syndrome (0xb741)
memory row (row 0)
memory channel (channel 1)
DIMM label, if set prior (DIMM B1
and then an optional, driver-specific message that may
have additional information.
Both UEs and CEs with no info will lack all but memory controller,
error type, a notice of "no info" and then an optional,
driver-specific error message.
============================================================================
PCI Bus Parity Detection
On Header Type 00 devices the primary status is looked at
for any parity error regardless of whether Parity is enabled on the
device. (The spec indicates parity is generated in some cases).
On Header Type 01 bridges, the secondary status register is also
looked at to see if parity occurred on the bus on the other side of
the bridge.
SYSFS CONFIGURATION
Under /sys/devices/system/edac/pci are control and attribute files as follows:
Enable/Disable PCI Parity checking control file:
'check_pci_parity'
This control file enables or disables the PCI Bus Parity scanning
operation. Writing a 1 to this file enables the scanning. Writing
a 0 to this file disables the scanning.
Enable:
echo "1" >/sys/devices/system/edac/pci/check_pci_parity
Disable:
echo "0" >/sys/devices/system/edac/pci/check_pci_parity
Parity Count:
'pci_parity_count'
This attribute file will display the number of parity errors that
have been detected.
============================================================================
MODULE PARAMETERS
Panic on UE control file:
'edac_mc_panic_on_ue'
An uncorrectable error will cause a machine panic. This is usually
desirable. It is a bad idea to continue when an uncorrectable error
occurs - it is indeterminate what was uncorrected and the operating
system context might be so mangled that continuing will lead to further
corruption. If the kernel has MCE configured, then EDAC will never
notice the UE.
LOAD TIME: module/kernel parameter: edac_mc_panic_on_ue=[0|1]
RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_panic_on_ue
Log UE control file:
'edac_mc_log_ue'
Generate kernel messages describing uncorrectable errors. These errors
are reported through the system message log system. UE statistics
will be accumulated even when UE logging is disabled.
LOAD TIME: module/kernel parameter: edac_mc_log_ue=[0|1]
RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_log_ue
Log CE control file:
'edac_mc_log_ce'
Generate kernel messages describing correctable errors. These
errors are reported through the system message log system.
CE statistics will be accumulated even when CE logging is disabled.
LOAD TIME: module/kernel parameter: edac_mc_log_ce=[0|1]
RUN TIME: echo "1" > /sys/module/edac_core/parameters/edac_mc_log_ce
Polling period control file:
'edac_mc_poll_msec'
The time period, in milliseconds, for polling for error information.
Too small a value wastes resources. Too large a value might delay
necessary handling of errors and might loose valuable information for
locating the error. 1000 milliseconds (once each second) is the current
default. Systems which require all the bandwidth they can get, may
increase this.
LOAD TIME: module/kernel parameter: edac_mc_poll_msec=[0|1]
RUN TIME: echo "1000" > /sys/module/edac_core/parameters/edac_mc_poll_msec
Panic on PCI PARITY Error:
'panic_on_pci_parity'
This control files enables or disables panicking when a parity
error has been detected.
module/kernel parameter: edac_panic_on_pci_pe=[0|1]
Enable:
echo "1" > /sys/module/edac_core/parameters/edac_panic_on_pci_pe
Disable:
echo "0" > /sys/module/edac_core/parameters/edac_panic_on_pci_pe
=======================================================================
EDAC_DEVICE type of device
In the header file, edac_core.h, there is a series of edac_device structures
and APIs for the EDAC_DEVICE.
User space access to an edac_device is through the sysfs interface.
At the location /sys/devices/system/edac (sysfs) new edac_device devices will
appear.
There is a three level tree beneath the above 'edac' directory. For example,
the 'test_device_edac' device (found at the bluesmoke.sourceforget.net website)
installs itself as:
/sys/devices/systm/edac/test-instance
in this directory are various controls, a symlink and one or more 'instance'
directorys.
The standard default controls are:
log_ce boolean to log CE events
log_ue boolean to log UE events
panic_on_ue boolean to 'panic' the system if an UE is encountered
(default off, can be set true via startup script)
poll_msec time period between POLL cycles for events
The test_device_edac device adds at least one of its own custom control:
test_bits which in the current test driver does nothing but
show how it is installed. A ported driver can
add one or more such controls and/or attributes
for specific uses.
One out-of-tree driver uses controls here to allow
for ERROR INJECTION operations to hardware
injection registers
The symlink points to the 'struct dev' that is registered for this edac_device.
INSTANCES
One or more instance directories are present. For the 'test_device_edac' case:
test-instance0
In this directory there are two default counter attributes, which are totals of
counter in deeper subdirectories.
ce_count total of CE events of subdirectories
ue_count total of UE events of subdirectories
BLOCKS
At the lowest directory level is the 'block' directory. There can be 0, 1
or more blocks specified in each instance.
test-block0
In this directory the default attributes are:
ce_count which is counter of CE events for this 'block'
of hardware being monitored
ue_count which is counter of UE events for this 'block'
of hardware being monitored
The 'test_device_edac' device adds 4 attributes and 1 control:
test-block-bits-0 for every POLL cycle this counter
is incremented
test-block-bits-1 every 10 cycles, this counter is bumped once,
and test-block-bits-0 is set to 0
test-block-bits-2 every 100 cycles, this counter is bumped once,
and test-block-bits-1 is set to 0
test-block-bits-3 every 1000 cycles, this counter is bumped once,
and test-block-bits-2 is set to 0
reset-counters writing ANY thing to this control will
reset all the above counters.
Use of the 'test_device_edac' driver should any others to create their own
unique drivers for their hardware systems.
The 'test_device_edac' sample driver is located at the
bluesmoke.sourceforge.net project site for EDAC.
=======================================================================
NEHALEM USAGE OF EDAC APIs
This chapter documents some EXPERIMENTAL mappings for EDAC API to handle
Nehalem EDAC driver. They will likely be changed on future versions
of the driver.
Due to the way Nehalem exports Memory Controller data, some adjustments
were done at i7core_edac driver. This chapter will cover those differences
1) On Nehalem, there are one Memory Controller per Quick Patch Interconnect
(QPI). At the driver, the term "socket" means one QPI. This is
associated with a physical CPU socket.
Each MC have 3 physical read channels, 3 physical write channels and
3 logic channels. The driver currently sees it as just 3 channels.
Each channel can have up to 3 DIMMs.
The minimum known unity is DIMMs. There are no information about csrows.
As EDAC API maps the minimum unity is csrows, the driver sequencially
maps channel/dimm into different csrows.
For example, supposing the following layout:
Ch0 phy rd0, wr0 (0x063f4031): 2 ranks, UDIMMs
dimm 0 1024 Mb offset: 0, bank: 8, rank: 1, row: 0x4000, col: 0x400
dimm 1 1024 Mb offset: 4, bank: 8, rank: 1, row: 0x4000, col: 0x400
Ch1 phy rd1, wr1 (0x063f4031): 2 ranks, UDIMMs
dimm 0 1024 Mb offset: 0, bank: 8, rank: 1, row: 0x4000, col: 0x400
Ch2 phy rd3, wr3 (0x063f4031): 2 ranks, UDIMMs
dimm 0 1024 Mb offset: 0, bank: 8, rank: 1, row: 0x4000, col: 0x400
The driver will map it as:
csrow0: channel 0, dimm0
csrow1: channel 0, dimm1
csrow2: channel 1, dimm0
csrow3: channel 2, dimm0
exports one
DIMM per csrow.
Each QPI is exported as a different memory controller.
2) Nehalem MC has the hability to generate errors. The driver implements this
functionality via some error injection nodes:
For injecting a memory error, there are some sysfs nodes, under
/sys/devices/system/edac/mc/mc?/:
inject_addrmatch/*:
Controls the error injection mask register. It is possible to specify
several characteristics of the address to match an error code:
dimm = the affected dimm. Numbers are relative to a channel;
rank = the memory rank;
channel = the channel that will generate an error;
bank = the affected bank;
page = the page address;
column (or col) = the address column.
each of the above values can be set to "any" to match any valid value.
At driver init, all values are set to any.
For example, to generate an error at rank 1 of dimm 2, for any channel,
any bank, any page, any column:
echo 2 >/sys/devices/system/edac/mc/mc0/inject_addrmatch/dimm
echo 1 >/sys/devices/system/edac/mc/mc0/inject_addrmatch/rank
To return to the default behaviour of matching any, you can do:
echo any >/sys/devices/system/edac/mc/mc0/inject_addrmatch/dimm
echo any >/sys/devices/system/edac/mc/mc0/inject_addrmatch/rank
inject_eccmask:
specifies what bits will have troubles,
inject_section:
specifies what ECC cache section will get the error:
3 for both
2 for the highest
1 for the lowest
inject_type:
specifies the type of error, being a combination of the following bits:
bit 0 - repeat
bit 1 - ecc
bit 2 - parity
inject_enable starts the error generation when something different
than 0 is written.
All inject vars can be read. root permission is needed for write.
Datasheet states that the error will only be generated after a write on an
address that matches inject_addrmatch. It seems, however, that reading will
also produce an error.
For example, the following code will generate an error for any write access
at socket 0, on any DIMM/address on channel 2:
echo 2 >/sys/devices/system/edac/mc/mc0/inject_addrmatch/channel
echo 2 >/sys/devices/system/edac/mc/mc0/inject_type
echo 64 >/sys/devices/system/edac/mc/mc0/inject_eccmask
echo 3 >/sys/devices/system/edac/mc/mc0/inject_section
echo 1 >/sys/devices/system/edac/mc/mc0/inject_enable
dd if=/dev/mem of=/dev/null seek=16k bs=4k count=1 >& /dev/null
For socket 1, it is needed to replace "mc0" by "mc1" at the above
commands.
The generated error message will look like:
EDAC MC0: UE row 0, channel-a= 0 channel-b= 0 labels "-": NON_FATAL (addr = 0x0075b980, socket=0, Dimm=0, Channel=2, syndrome=0x00000040, count=1, Err=8c0000400001009f:4000080482 (read error: read ECC error))
3) Nehalem specific Corrected Error memory counters
Nehalem have some registers to count memory errors. The driver uses those
registers to report Corrected Errors on devices with Registered Dimms.
However, those counters don't work with Unregistered Dimms. As the chipset
offers some counters that also work with UDIMMS (but with a worse level of
granularity than the default ones), the driver exposes those registers for
UDIMM memories.
They can be read by looking at the contents of all_channel_counts/
$ for i in /sys/devices/system/edac/mc/mc0/all_channel_counts/*; do echo $i; cat $i; done
/sys/devices/system/edac/mc/mc0/all_channel_counts/udimm0
0
/sys/devices/system/edac/mc/mc0/all_channel_counts/udimm1
0
/sys/devices/system/edac/mc/mc0/all_channel_counts/udimm2
0
What happens here is that errors on different csrows, but at the same
dimm number will increment the same counter.
So, in this memory mapping:
csrow0: channel 0, dimm0
csrow1: channel 0, dimm1
csrow2: channel 1, dimm0
csrow3: channel 2, dimm0
The hardware will increment udimm0 for an error at the first dimm at either
csrow0, csrow2 or csrow3;
The hardware will increment udimm1 for an error at the second dimm at either
csrow0, csrow2 or csrow3;
The hardware will increment udimm2 for an error at the third dimm at either
csrow0, csrow2 or csrow3;
4) Standard error counters
The standard error counters are generated when an mcelog error is received
by the driver. Since, with udimm, this is counted by software, it is
possible that some errors could be lost. With rdimm's, they displays the
contents of the registers
View Git Blame Copy Permalink