mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-28 15:13:55 +08:00
efdbd7345f
This is a quite large renaming to consolidate display related bindings into a single "display" directory from various scattered locations of video, drm, gpu, fb, mipi, and panel. The prior location was somewhat based on the Linux driver location, but bindings should be independent of that. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org>
111 lines
4.5 KiB
Plaintext
111 lines
4.5 KiB
Plaintext
Device-Tree bindings for Samsung SoC display controller (FIMD)
|
|
|
|
FIMD (Fully Interactive Mobile Display) is the Display Controller for the
|
|
Samsung series of SoCs which transfers the image data from a video memory
|
|
buffer to an external LCD interface.
|
|
|
|
Required properties:
|
|
- compatible: value should be one of the following
|
|
"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
|
|
"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
|
|
"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
|
|
"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
|
|
"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
|
|
"samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
|
|
"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
|
|
|
|
- reg: physical base address and length of the FIMD registers set.
|
|
|
|
- interrupt-parent: should be the phandle of the fimd controller's
|
|
parent interrupt controller.
|
|
|
|
- interrupts: should contain a list of all FIMD IP block interrupts in the
|
|
order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
|
|
format depends on the interrupt controller used.
|
|
|
|
- interrupt-names: should contain the interrupt names: "fifo", "vsync",
|
|
"lcd_sys", in the same order as they were listed in the interrupts
|
|
property.
|
|
|
|
- pinctrl-0: pin control group to be used for this controller.
|
|
|
|
- pinctrl-names: must contain a "default" entry.
|
|
|
|
- clocks: must include clock specifiers corresponding to entries in the
|
|
clock-names property.
|
|
|
|
- clock-names: list of clock names sorted in the same order as the clocks
|
|
property. Must contain "sclk_fimd" and "fimd".
|
|
|
|
Optional Properties:
|
|
- power-domains: a phandle to FIMD power domain node.
|
|
- samsung,invert-vden: video enable signal is inverted
|
|
- samsung,invert-vclk: video clock signal is inverted
|
|
- display-timings: timing settings for FIMD, as described in document [1].
|
|
Can be used in case timings cannot be provided otherwise
|
|
or to override timings provided by the panel.
|
|
- samsung,sysreg: handle to syscon used to control the system registers
|
|
- i80-if-timings: timing configuration for lcd i80 interface support.
|
|
- cs-setup: clock cycles for the active period of address signal is enabled
|
|
until chip select is enabled.
|
|
If not specified, the default value(0) will be used.
|
|
- wr-setup: clock cycles for the active period of CS signal is enabled until
|
|
write signal is enabled.
|
|
If not specified, the default value(0) will be used.
|
|
- wr-active: clock cycles for the active period of CS is enabled.
|
|
If not specified, the default value(1) will be used.
|
|
- wr-hold: clock cycles for the active period of CS is disabled until write
|
|
signal is disabled.
|
|
If not specified, the default value(0) will be used.
|
|
|
|
The parameters are defined as:
|
|
|
|
VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
|
|
: : : : :
|
|
Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
|
|
| cs-setup+1 | : : :
|
|
|<---------->| : : :
|
|
Chip Select ???????????????|____________:____________:____________|??
|
|
| wr-setup+1 | | wr-hold+1 |
|
|
|<---------->| |<---------->|
|
|
Write Enable ????????????????????????????|____________|???????????????
|
|
| wr-active+1|
|
|
|<---------->|
|
|
Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
|
|
|
|
The device node can contain 'port' child nodes according to the bindings defined
|
|
in [2]. The following are properties specific to those nodes:
|
|
- reg: (required) port index, can be:
|
|
0 - for CAMIF0 input,
|
|
1 - for CAMIF1 input,
|
|
2 - for CAMIF2 input,
|
|
3 - for parallel output,
|
|
4 - for write-back interface
|
|
|
|
[1]: Documentation/devicetree/bindings/display/display-timing.txt
|
|
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
|
|
|
|
Example:
|
|
|
|
SoC specific DT entry:
|
|
|
|
fimd@11c00000 {
|
|
compatible = "samsung,exynos4210-fimd";
|
|
interrupt-parent = <&combiner>;
|
|
reg = <0x11c00000 0x20000>;
|
|
interrupt-names = "fifo", "vsync", "lcd_sys";
|
|
interrupts = <11 0>, <11 1>, <11 2>;
|
|
clocks = <&clock 140>, <&clock 283>;
|
|
clock-names = "sclk_fimd", "fimd";
|
|
power-domains = <&pd_lcd0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
Board specific DT entry:
|
|
|
|
fimd@11c00000 {
|
|
pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|