2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-24 05:04:00 +08:00
linux-next/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt
James Hogan 79bb646001 gpio-tz1090-pdc: add TZ1090 PDC gpio driver
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.

The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.

Changes in v4:
 - fix typos in DT bindings compatible properties
 - reference Documentation/devicetree/bindings/gpio/gpio.txt in
   gpio-ranges description in DT bindings
 - fix gpio-ranges examples in DT bindings (it must now have 3 cells)

Changes in v3:
 - separated from irq-imgpdc and removed arch/metag changes to allow
   these patches to go upstream separately via the pinctrl[/gpio] trees
   (particularly the pinctrl drivers depend on the new pinconf DT
   bindings).
 - some s/unsigned/unsigned int/.
 - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
   <dt-bindings/interrupt-controller/irq.h> flags in bindings.
 - gpio-tz1090*: move initcall from postcore to subsys.

Changes in v2:
 - gpio-tz1090-pdc: remove references to Linux flags in dt bindings
 - gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
 - gpio-tz1090-pdc: make register accessors inline to match pinctrl
 - gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
   breakage

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-07-20 19:03:48 +02:00

46 lines
1.3 KiB
Plaintext

ImgTec TZ1090 PDC GPIO Controller
Required properties:
- compatible: Compatible property value should be "img,tz1090-pdc-gpio".
- reg: Physical base address of the controller and length of memory mapped
region. This starts at and cover the SOC_GPIO_CONTROL registers.
- gpio-controller: Specifies that the node is a gpio controller.
- #gpio-cells: Should be 2. The syntax of the gpio specifier used by client
nodes should have the following values.
<[phandle of the gpio controller node]
[PDC gpio number]
[gpio flags]>
Values for gpio specifier:
- GPIO number: a value in the range 0 to 6.
- GPIO flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
Only the following flags are supported:
GPIO_ACTIVE_HIGH
GPIO_ACTIVE_LOW
Optional properties:
- gpio-ranges: Mapping to pin controller pins (as described in
Documentation/devicetree/bindings/gpio/gpio.txt)
- interrupts: Individual syswake interrupts (other GPIOs cannot interrupt)
Example:
pdc_gpios: gpio-controller@02006500 {
gpio-controller;
#gpio-cells = <2>;
compatible = "img,tz1090-pdc-gpio";
reg = <0x02006500 0x100>;
interrupt-parent = <&pdc>;
interrupts = <8 IRQ_TYPE_NONE>, /* Syswake 0 */
<9 IRQ_TYPE_NONE>, /* Syswake 1 */
<10 IRQ_TYPE_NONE>; /* Syswake 2 */
gpio-ranges = <&pdc_pinctrl 0 0 7>;
};