mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-21 11:44:01 +08:00
176 lines
4.6 KiB
C
176 lines
4.6 KiB
C
/*
|
|
* This driver adapted from Drew Eckhardt's Trantor T128 driver
|
|
*
|
|
* Copyright 1993, Drew Eckhardt
|
|
* Visionary Computing
|
|
* (Unix and Linux consulting and custom programming)
|
|
* drew@colorado.edu
|
|
* +1 (303) 666-5836
|
|
*
|
|
* ( Based on T128 - DISTRIBUTION RELEASE 3. )
|
|
*
|
|
* Modified to work with the Pro Audio Spectrum/Studio 16
|
|
* by John Weidman.
|
|
*
|
|
*
|
|
* For more information, please consult
|
|
*
|
|
* Media Vision
|
|
* (510) 770-8600
|
|
* (800) 348-7116
|
|
*
|
|
* and
|
|
*
|
|
* NCR 5380 Family
|
|
* SCSI Protocol Controller
|
|
* Databook
|
|
*
|
|
* NCR Microelectronics
|
|
* 1635 Aeroplaza Drive
|
|
* Colorado Springs, CO 80916
|
|
* 1+ (719) 578-3400
|
|
* 1+ (800) 334-5454
|
|
*/
|
|
|
|
|
|
#ifndef PAS16_H
|
|
#define PAS16_H
|
|
|
|
#define PAS16_PUBLIC_RELEASE 3
|
|
|
|
#define PDEBUG_INIT 0x1
|
|
#define PDEBUG_TRANSFER 0x2
|
|
|
|
#define PAS16_DEFAULT_BASE_1 0x388
|
|
#define PAS16_DEFAULT_BASE_2 0x384
|
|
#define PAS16_DEFAULT_BASE_3 0x38c
|
|
#define PAS16_DEFAULT_BASE_4 0x288
|
|
|
|
#define PAS16_DEFAULT_BOARD_1_IRQ 10
|
|
#define PAS16_DEFAULT_BOARD_2_IRQ 12
|
|
#define PAS16_DEFAULT_BOARD_3_IRQ 14
|
|
#define PAS16_DEFAULT_BOARD_4_IRQ 15
|
|
|
|
|
|
/*
|
|
* The Pro Audio Spectrum boards are I/O mapped. They use a Zilog 5380
|
|
* SCSI controller, which is the equivalent of NCR's 5380. "Pseudo-DMA"
|
|
* architecture is used, where a PAL drives the DMA signals on the 5380
|
|
* allowing fast, blind transfers with proper handshaking.
|
|
*/
|
|
|
|
|
|
/* The Time-out Counter register is used to safe-guard against a stuck
|
|
* bus (in the case of RDY driven handshake) or a stuck byte (if 16-Bit
|
|
* DMA conversion is used). The counter uses a 28.224MHz clock
|
|
* divided by 14 as its clock source. In the case of a stuck byte in
|
|
* the holding register, an interrupt is generated (and mixed with the
|
|
* one with the drive) using the CD-ROM interrupt pointer.
|
|
*/
|
|
|
|
#define P_TIMEOUT_COUNTER_REG 0x4000
|
|
#define P_TC_DISABLE 0x80 /* Set to 0 to enable timeout int. */
|
|
/* Bits D6-D0 contain timeout count */
|
|
|
|
|
|
#define P_TIMEOUT_STATUS_REG_OFFSET 0x4001
|
|
#define P_TS_TIM 0x80 /* check timeout status */
|
|
/* Bits D6-D4 N/U */
|
|
#define P_TS_ARM_DRQ_INT 0x08 /* Arm DRQ Int. When set high,
|
|
* the next rising edge will
|
|
* cause a CD-ROM interrupt.
|
|
* When set low, the interrupt
|
|
* will be cleared. There is
|
|
* no status available for
|
|
* this interrupt.
|
|
*/
|
|
#define P_TS_ENABLE_TO_ERR_INTERRUPT /* Enable timeout error int. */
|
|
#define P_TS_ENABLE_WAIT /* Enable Wait */
|
|
|
|
#define P_TS_CT 0x01 /* clear timeout. Note: writing
|
|
* to this register clears the
|
|
* timeout error int. or status
|
|
*/
|
|
|
|
|
|
/*
|
|
* The data register reads/writes to/from the 5380 in pseudo-DMA mode
|
|
*/
|
|
|
|
#define P_DATA_REG_OFFSET 0x5c00 /* rw */
|
|
|
|
#define P_STATUS_REG_OFFSET 0x5c01 /* ro */
|
|
#define P_ST_RDY 0x80 /* 5380 DDRQ Status */
|
|
|
|
#define P_IRQ_STATUS 0x5c03
|
|
#define P_IS_IRQ 0x80 /* DIRQ status */
|
|
|
|
#define PCB_CONFIG 0x803
|
|
#define MASTER_ADDRESS_PTR 0x9a01 /* Fixed position - no relo */
|
|
#define SYS_CONFIG_4 0x8003
|
|
#define WAIT_STATE 0xbc00
|
|
#define OPERATION_MODE_1 0xec03
|
|
#define IO_CONFIG_3 0xf002
|
|
|
|
|
|
#ifndef ASM
|
|
static int pas16_abort(Scsi_Cmnd *);
|
|
static int pas16_biosparam(struct scsi_device *, struct block_device *,
|
|
sector_t, int*);
|
|
static int pas16_detect(struct scsi_host_template *);
|
|
static int pas16_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
|
|
static int pas16_bus_reset(Scsi_Cmnd *);
|
|
|
|
#ifndef CMD_PER_LUN
|
|
#define CMD_PER_LUN 2
|
|
#endif
|
|
|
|
#ifndef CAN_QUEUE
|
|
#define CAN_QUEUE 32
|
|
#endif
|
|
|
|
#ifndef HOSTS_C
|
|
|
|
#define NCR5380_implementation_fields \
|
|
volatile unsigned short io_port
|
|
|
|
#define NCR5380_local_declare() \
|
|
volatile unsigned short io_port
|
|
|
|
#define NCR5380_setup(instance) \
|
|
io_port = (instance)->io_port
|
|
|
|
#define PAS16_io_port(reg) ( io_port + pas16_offset[(reg)] )
|
|
|
|
#if !(PDEBUG & PDEBUG_TRANSFER)
|
|
#define NCR5380_read(reg) ( inb(PAS16_io_port(reg)) )
|
|
#define NCR5380_write(reg, value) ( outb((value),PAS16_io_port(reg)) )
|
|
#else
|
|
#define NCR5380_read(reg) \
|
|
(((unsigned char) printk("scsi%d : read register %d at io_port %04x\n"\
|
|
, instance->hostno, (reg), PAS16_io_port(reg))), inb( PAS16_io_port(reg)) )
|
|
|
|
#define NCR5380_write(reg, value) \
|
|
(printk("scsi%d : write %02x to register %d at io_port %04x\n", \
|
|
instance->hostno, (value), (reg), PAS16_io_port(reg)), \
|
|
outb( (value),PAS16_io_port(reg) ) )
|
|
|
|
#endif
|
|
|
|
|
|
#define NCR5380_intr pas16_intr
|
|
#define do_NCR5380_intr do_pas16_intr
|
|
#define NCR5380_queue_command pas16_queue_command
|
|
#define NCR5380_abort pas16_abort
|
|
#define NCR5380_bus_reset pas16_bus_reset
|
|
#define NCR5380_proc_info pas16_proc_info
|
|
|
|
/* 15 14 12 10 7 5 3
|
|
1101 0100 1010 1000 */
|
|
|
|
#define PAS16_IRQS 0xd4a8
|
|
|
|
#endif /* else def HOSTS_C */
|
|
#endif /* ndef ASM */
|
|
#endif /* PAS16_H */
|