mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-22 12:14:01 +08:00
de6f86ce51
Add a notion about 16C950 UART, that is using DTR signal for RS485 mode. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
121 lines
3.3 KiB
Plaintext
121 lines
3.3 KiB
Plaintext
RS485 SERIAL COMMUNICATIONS
|
|
|
|
1. INTRODUCTION
|
|
|
|
EIA-485, also known as TIA/EIA-485 or RS-485, is a standard defining the
|
|
electrical characteristics of drivers and receivers for use in balanced
|
|
digital multipoint systems.
|
|
This standard is widely used for communications in industrial automation
|
|
because it can be used effectively over long distances and in electrically
|
|
noisy environments.
|
|
|
|
2. HARDWARE-RELATED CONSIDERATIONS
|
|
|
|
Some CPUs/UARTs (e.g., Atmel AT91 or 16C950 UART) contain a built-in
|
|
half-duplex mode capable of automatically controlling line direction by
|
|
toggling RTS or DTR signals. That can be used to control external
|
|
half-duplex hardware like an RS485 transceiver or any RS232-connected
|
|
half-duplex devices like some modems.
|
|
|
|
For these microcontrollers, the Linux driver should be made capable of
|
|
working in both modes, and proper ioctls (see later) should be made
|
|
available at user-level to allow switching from one mode to the other, and
|
|
vice versa.
|
|
|
|
3. DATA STRUCTURES ALREADY AVAILABLE IN THE KERNEL
|
|
|
|
The Linux kernel provides the serial_rs485 structure (see [1]) to handle
|
|
RS485 communications. This data structure is used to set and configure RS485
|
|
parameters in the platform data and in ioctls.
|
|
|
|
Any driver for devices capable of working both as RS232 and RS485 should
|
|
provide at least the following ioctls:
|
|
|
|
- TIOCSRS485 (typically associated with number 0x542F). This ioctl is used
|
|
to enable/disable RS485 mode from user-space
|
|
|
|
- TIOCGRS485 (typically associated with number 0x542E). This ioctl is used
|
|
to get RS485 mode from kernel-space (i.e., driver) to user-space.
|
|
|
|
In other words, the serial driver should contain a code similar to the next
|
|
one:
|
|
|
|
static struct uart_ops atmel_pops = {
|
|
/* ... */
|
|
.ioctl = handle_ioctl,
|
|
};
|
|
|
|
static int handle_ioctl(struct uart_port *port,
|
|
unsigned int cmd,
|
|
unsigned long arg)
|
|
{
|
|
struct serial_rs485 rs485conf;
|
|
|
|
switch (cmd) {
|
|
case TIOCSRS485:
|
|
if (copy_from_user(&rs485conf,
|
|
(struct serial_rs485 *) arg,
|
|
sizeof(rs485conf)))
|
|
return -EFAULT;
|
|
|
|
/* ... */
|
|
break;
|
|
|
|
case TIOCGRS485:
|
|
if (copy_to_user((struct serial_rs485 *) arg,
|
|
...,
|
|
sizeof(rs485conf)))
|
|
return -EFAULT;
|
|
/* ... */
|
|
break;
|
|
|
|
/* ... */
|
|
}
|
|
}
|
|
|
|
|
|
4. USAGE FROM USER-LEVEL
|
|
|
|
From user-level, RS485 configuration can be get/set using the previous
|
|
ioctls. For instance, to set RS485 you can use the following code:
|
|
|
|
#include <linux/serial.h>
|
|
|
|
/* Driver-specific ioctls: */
|
|
#define TIOCGRS485 0x542E
|
|
#define TIOCSRS485 0x542F
|
|
|
|
/* Open your specific device (e.g., /dev/mydevice): */
|
|
int fd = open ("/dev/mydevice", O_RDWR);
|
|
if (fd < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
struct serial_rs485 rs485conf;
|
|
|
|
/* Set RS485 mode: */
|
|
rs485conf.flags |= SER_RS485_ENABLED;
|
|
|
|
/* Set rts delay before send, if needed: */
|
|
rs485conf.flags |= SER_RS485_RTS_BEFORE_SEND;
|
|
rs485conf.delay_rts_before_send = ...;
|
|
|
|
/* Set rts delay after send, if needed: */
|
|
rs485conf.flags |= SER_RS485_RTS_AFTER_SEND;
|
|
rs485conf.delay_rts_after_send = ...;
|
|
|
|
if (ioctl (fd, TIOCSRS485, &rs485conf) < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
/* Use read() and write() syscalls here... */
|
|
|
|
/* Close the device when finished: */
|
|
if (close (fd) < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
5. REFERENCES
|
|
|
|
[1] include/linux/serial.h
|