renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-28 23:23:55 +08:00
Code
db2f7fe562
linux-next/arch/arm/boot/dts/imx28-m28cu3.dts
Thomas Gleixner fcaf20360a treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 159 
Based on 1 normalized pattern(s):

  the code contained herein is licensed under the gnu general public
  license you may obtain a copy of the gnu general public license
  version 2 or later at the following locations http www opensource
  org licenses gpl license html http www gnu org copyleft gpl html

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 161 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:37 -07:00

267 lines
5.6 KiB
Plaintext
Raw Blame History

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2013 Marek Vasut <marex@denx.de>
*/
/dts-v1/;
#include "imx28.dtsi"
/ {
model = "MSR M28CU3";
compatible = "msr,m28cu3", "fsl,imx28";
memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
gpmi-nand@8000c000 {
#address-cells = <1>;
#size-cells = <1>;
pinctrl-names = "default";
pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
status = "okay";
partition@0 {
label = "gpmi-nfc-0-boot";
reg = <0x00000000 0x01400000>;
read-only;
};
partition@1 {
label = "gpmi-nfc-general-use";
reg = <0x01400000 0x0ec00000>;
};
};
ssp0: spi@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a
&mmc0_cd_cfg
&mmc0_sck_cfg>;
bus-width = <4>;
vmmc-supply = <&reg_vddio_sd0>;
status = "okay";
};
ssp2: spi@80014000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_a
&mmc2_cd_cfg
&mmc2_sck_cfg_a>;
bus-width = <4>;
vmmc-supply = <&reg_vddio_sd1>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS0__GPIO_2_19
MX28_PAD_PWM4__GPIO_3_29
MX28_PAD_AUART2_RX__GPIO_3_8
MX28_PAD_ENET0_RX_CLK__GPIO_4_13
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_m28: lcdif-m28@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_VSYNC__LCD_VSYNC
MX28_PAD_LCD_HSYNC__LCD_HSYNC
MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
MX28_PAD_LCD_RESET__LCD_RESET
MX28_PAD_LCD_CS__LCD_ENABLE
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_gpio: leds-m28@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP3_MISO__GPIO_2_26
MX28_PAD_SSP3_SCK__GPIO_2_24
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
ocotp@8002c000 {
status = "okay";
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_m28>;
display = <&display0>;
status = "okay";
display0: display0 {
bits-per-pixel = <32>;
bus-width = <24>;
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <6410256>;
hactive = <320>;
vactive = <240>;
hback-porch = <38>;
hfront-porch = <20>;
vback-porch = <15>;
vfront-porch = <5>;
hsync-len = <30>;
vsync-len = <3>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
};
};
};
};
apbx@80040000 {
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_b>;
status = "okay";
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
auart3: serial@80070000 {
pinctrl-names = "default";
pinctrl-0 = <&auart3_2pins_b>;
status = "okay";
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pins_a>;
status = "okay";
};
};
};
ahb@80080000 {
usb1: usb@80090000 {
vbus-supply = <&reg_usb1_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&usb1_pins_a>;
disable-over-current;
status = "okay";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
phy-reset-duration = <100>;
status = "okay";
};
mac1: ethernet@800f4000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac1_pins_a>;
status = "okay";
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_gpio>;
user1 {
label = "sd0-led";
gpios = <&gpio2 26 0>;
linux,default-trigger = "mmc0";
};
user2 {
label = "sd1-led";
gpios = <&gpio2 24 0>;
linux,default-trigger = "mmc2";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_vddio_sd0: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "vddio-sd0";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio3 29 0>;
};
reg_vddio_sd1: regulator@2 {
compatible = "regulator-fixed";
reg = <2>;
regulator-name = "vddio-sd1";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio2 19 0>;
};
reg_usb1_vbus: regulator@3 {
compatible = "regulator-fixed";
reg = <3>;
regulator-name = "usb1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 8 0>;
enable-active-high;
};
};
};
View Git Blame Copy Permalink