mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 06:34:11 +08:00
efdbd7345f
This is a quite large renaming to consolidate display related bindings into a single "display" directory from various scattered locations of video, drm, gpu, fb, mipi, and panel. The prior location was somewhat based on the Linux driver location, but bindings should be independent of that. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org>
89 lines
2.7 KiB
Plaintext
89 lines
2.7 KiB
Plaintext
Analog Device ADV7511(W)/13 HDMI Encoders
|
|
-----------------------------------------
|
|
|
|
The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters
|
|
compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
|
|
S/PDIF, CEC and HDCP.
|
|
|
|
Required properties:
|
|
|
|
- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513"
|
|
- reg: I2C slave address
|
|
|
|
The ADV7511 supports a large number of input data formats that differ by their
|
|
color depth, color format, clock mode, bit justification and random
|
|
arrangement of components on the data bus. The combination of the following
|
|
properties describe the input and map directly to the video input tables of the
|
|
ADV7511 datasheet that document all the supported combinations.
|
|
|
|
- adi,input-depth: Number of bits per color component at the input (8, 10 or
|
|
12).
|
|
- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
|
|
"yuv444".
|
|
- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
|
|
pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
|
|
data driven on both edges).
|
|
|
|
The following input format properties are required except in "rgb 1x" and
|
|
"yuv444 1x" modes, in which case they must not be specified.
|
|
|
|
- adi,input-style: The input components arrangement variant (1, 2 or 3), as
|
|
listed in the input format tables in the datasheet.
|
|
- adi,input-justification: The input bit justification ("left", "evenly",
|
|
"right").
|
|
|
|
Optional properties:
|
|
|
|
- interrupts: Specifier for the ADV7511 interrupt
|
|
- pd-gpios: Specifier for the GPIO connected to the power down signal
|
|
|
|
- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
|
|
(-1200 ps .. 1600 ps). Defaults to no delay.
|
|
- adi,embedded-sync: The input uses synchronization signals embedded in the
|
|
data stream (similar to BT.656). Defaults to separate H/V synchronization
|
|
signals.
|
|
|
|
Required nodes:
|
|
|
|
The ADV7511 has two video ports. Their connections are modelled using the OF
|
|
graph bindings specified in Documentation/devicetree/bindings/graph.txt.
|
|
|
|
- Video port 0 for the RGB or YUV input
|
|
- Video port 1 for the HDMI output
|
|
|
|
|
|
Example
|
|
-------
|
|
|
|
adv7511w: hdmi@39 {
|
|
compatible = "adi,adv7511w";
|
|
reg = <39>;
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
adi,input-depth = <8>;
|
|
adi,input-colorspace = "rgb";
|
|
adi,input-clock = "1x";
|
|
adi,input-style = <1>;
|
|
adi,input-justification = "evenly";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
adv7511w_in: endpoint {
|
|
remote-endpoint = <&dpi_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
adv7511_out: endpoint {
|
|
remote-endpoint = <&hdmi_connector_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|