mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-28 15:13:55 +08:00
7b240e44d0
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Rob Herring <robh@kernel.org>
54 lines
2.2 KiB
Plaintext
54 lines
2.2 KiB
Plaintext
* Marvell UART : Non standard UART used in some of Marvell EBU SoCs
|
|
e.g., Armada-3700.
|
|
|
|
Required properties:
|
|
- compatible:
|
|
- "marvell,armada-3700-uart" for the standard variant of the UART
|
|
(32 bytes FIFO, no DMA, level interrupts, 8-bit access to the
|
|
FIFO, baudrate limited to 230400).
|
|
- "marvell,armada-3700-uart-ext" for the extended variant of the
|
|
UART (128 bytes FIFO, DMA, front interrupts, 8-bit or 32-bit
|
|
accesses to the FIFO, baudrate unlimited by the dividers).
|
|
- reg: offset and length of the register set for the device.
|
|
- clocks: UART reference clock used to derive the baudrate. If no clock
|
|
is provided (possible only with the "marvell,armada-3700-uart"
|
|
compatible string for backward compatibility), it will only work
|
|
if the baudrate was initialized by the bootloader and no baudrate
|
|
change will then be possible.
|
|
- interrupts:
|
|
- Must contain three elements for the standard variant of the IP
|
|
(marvell,armada-3700-uart): "uart-sum", "uart-tx" and "uart-rx",
|
|
respectively the UART sum interrupt, the UART TX interrupt and
|
|
UART RX interrupt. A corresponding interrupt-names property must
|
|
be defined.
|
|
- Must contain two elements for the extended variant of the IP
|
|
(marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx",
|
|
respectively the UART TX interrupt and the UART RX interrupt. A
|
|
corresponding interrupt-names property must be defined.
|
|
- For backward compatibility reasons, a single element interrupts
|
|
property is also supported for the standard variant of the IP,
|
|
containing only the UART sum interrupt. This form is deprecated
|
|
and should no longer be used.
|
|
|
|
Example:
|
|
uart0: serial@12000 {
|
|
compatible = "marvell,armada-3700-uart";
|
|
reg = <0x12000 0x200>;
|
|
clocks = <&xtalclk>;
|
|
interrupts =
|
|
<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "uart-sum", "uart-tx", "uart-rx";
|
|
};
|
|
|
|
uart1: serial@12200 {
|
|
compatible = "marvell,armada-3700-uart-ext";
|
|
reg = <0x12200 0x30>;
|
|
clocks = <&xtalclk>;
|
|
interrupts =
|
|
<GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
|
|
<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>;
|
|
interrupt-names = "uart-tx", "uart-rx";
|
|
};
|