mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-26 22:24:09 +08:00
c4ac37193e
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
90 lines
3.1 KiB
Plaintext
90 lines
3.1 KiB
Plaintext
Wolfson Arizona class audio SoCs
|
|
|
|
These devices are audio SoCs with extensive digital capabilites and a range
|
|
of analogue I/O.
|
|
|
|
Required properties:
|
|
|
|
- compatible : One of the following chip-specific strings:
|
|
"wlf,wm5102"
|
|
"wlf,wm5110"
|
|
"wlf,wm8280"
|
|
"wlf,wm8997"
|
|
- reg : I2C slave address when connected using I2C, chip select number when
|
|
using SPI.
|
|
|
|
- interrupts : The interrupt line the /IRQ signal for the device is
|
|
connected to.
|
|
- interrupt-controller : Arizona class devices contain interrupt controllers
|
|
and may provide interrupt services to other devices.
|
|
- interrupt-parent : The parent interrupt controller.
|
|
- #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
|
|
The first cell is the IRQ number.
|
|
The second cell is the flags, encoded as the trigger masks from
|
|
Documentation/devicetree/bindings/interrupts.txt
|
|
|
|
- gpio-controller : Indicates this device is a GPIO controller.
|
|
- #gpio-cells : Must be 2. The first cell is the pin number and the
|
|
second cell is used to specify optional parameters (currently unused).
|
|
|
|
- AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device,
|
|
as covered in Documentation/devicetree/bindings/regulator/regulator.txt
|
|
|
|
- DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102,
|
|
wm5110, wm8280)
|
|
|
|
- SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102,
|
|
wm5110, wm8280)
|
|
|
|
- SPKVDD-supply : Speaker driver power supply (wm8997)
|
|
|
|
Optional properties:
|
|
|
|
- wlf,reset : GPIO specifier for the GPIO controlling /RESET
|
|
- wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA
|
|
|
|
- wlf,gpio-defaults : A list of GPIO configuration register values. If
|
|
absent, no configuration of these registers is performed. If any
|
|
entry has a value that is out of range for a 16 bit register then
|
|
the chip default will be used. If present exactly five values must
|
|
be specified.
|
|
|
|
- wlf,inmode : A list of INn_MODE register values, where n is the number
|
|
of input signals. Valid values are 0 (Differential), 1 (Single-ended) and
|
|
2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default.
|
|
If present, values must be specified less than or equal to the number of
|
|
input singals. If values less than the number of input signals, elements
|
|
that has not been specifed are set to 0 by default.
|
|
|
|
- DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
|
|
they are being externally supplied. As covered in
|
|
Documentation/devicetree/bindings/regulator/regulator.txt
|
|
|
|
Optional subnodes:
|
|
- ldo1 : Initial data for the LDO1 regulator, as covered in
|
|
Documentation/devicetree/bindings/regulator/regulator.txt
|
|
- micvdd : Initial data for the MICVDD regulator, as covered in
|
|
Documentation/devicetree/bindings/regulator/regulator.txt
|
|
|
|
Example:
|
|
|
|
codec: wm5102@1a {
|
|
compatible = "wlf,wm5102";
|
|
reg = <0x1a>;
|
|
interrupts = <347>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupt-parent = <&gic>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
wlf,gpio-defaults = <
|
|
0x00000000 /* AIF1TXLRCLK */
|
|
0xffffffff
|
|
0xffffffff
|
|
0xffffffff
|
|
0xffffffff
|
|
>;
|
|
};
|