renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-25 21:54:06 +08:00
Code
c2b65f8422
linux-next/drivers/usb/host/Kconfig
Jan Andersson fda928ac97 USB: UHCI: Support big endian GRUSBHC HC 
This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.

Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:45:32 -07:00

581 lines
19 KiB
Plaintext
Raw Blame History

#
# USB Host Controller Drivers
#
comment "USB Host Controller Drivers"
depends on USB
config USB_C67X00_HCD
tristate "Cypress C67x00 HCD support"
depends on USB
help
The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
host/peripheral/OTG USB controllers.
Enable this option to support this chip in host controller mode.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called c67x00.
config USB_XHCI_HCD
tristate "xHCI HCD (USB 3.0) support (EXPERIMENTAL)"
depends on USB && PCI && EXPERIMENTAL
---help---
The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
"SuperSpeed" host controller hardware.
To compile this driver as a module, choose M here: the
module will be called xhci-hcd.
config USB_XHCI_HCD_DEBUGGING
bool "Debugging for the xHCI host controller"
depends on USB_XHCI_HCD
---help---
Say 'Y' to turn on debugging for the xHCI host controller driver.
This will spew debugging output, even in interrupt context.
This should only be used for debugging xHCI driver bugs.
If unsure, say N.
config USB_EHCI_HCD
tristate "EHCI HCD (USB 2.0) support"
depends on USB && USB_ARCH_HAS_EHCI
---help---
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
If your USB host controller supports USB 2.0, you will likely want to
configure this Host Controller Driver.
EHCI controllers are packaged with "companion" host controllers (OHCI
or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
will connect to EHCI if the device is high speed, otherwise they
connect to a companion controller. If you configure EHCI, you should
probably configure the OHCI (for NEC and some other vendors) USB Host
Controller Driver or UHCI (for Via motherboards) Host Controller
Driver too.
You may want to read <file:Documentation/usb/ehci.txt>.
To compile this driver as a module, choose M here: the
module will be called ehci-hcd.
config USB_EHCI_ROOT_HUB_TT
bool "Root Hub Transaction Translators"
depends on USB_EHCI_HCD
---help---
Some EHCI chips have vendor-specific extensions to integrate
transaction translators, so that no OHCI or UHCI companion
controller is needed. It's safe to say "y" even if your
controller doesn't support this feature.
This supports the EHCI implementation that's originally
from ARC, and has since changed hands a few times.
config USB_EHCI_TT_NEWSCHED
bool "Improved Transaction Translator scheduling"
depends on USB_EHCI_HCD
default y
---help---
This changes the periodic scheduling code to fill more of the low
and full speed bandwidth available from the Transaction Translator
(TT) in USB 2.0 hubs. Without this, only one transfer will be
issued in each microframe, significantly reducing the number of
periodic low/fullspeed transfers possible.
If you have multiple periodic low/fullspeed devices connected to a
highspeed USB hub which is connected to a highspeed USB Host
Controller, and some of those devices will not work correctly
(possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
you have only one such device and it doesn't work, you could try
saying N.
If unsure, say Y.
config USB_EHCI_HCD_PMC_MSP
tristate "EHCI support for on-chip PMC MSP71xx USB controller"
depends on USB_EHCI_HCD && MSP_HAS_USB
default n
select USB_EHCI_BIG_ENDIAN_DESC
select USB_EHCI_BIG_ENDIAN_MMIO
---help---
Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
If unsure, say N.
config USB_EHCI_BIG_ENDIAN_MMIO
bool
depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \
ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
PPC_MPC512x || CPU_CAVIUM_OCTEON || \
PMC_MSP || SPARC_LEON)
default y
config USB_EHCI_BIG_ENDIAN_DESC
bool
depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
PPC_MPC512x || PMC_MSP || SPARC_LEON)
default y
config XPS_USB_HCD_XILINX
bool "Use Xilinx usb host EHCI controller core"
depends on USB_EHCI_HCD && (PPC32 || MICROBLAZE)
select USB_EHCI_BIG_ENDIAN_DESC
select USB_EHCI_BIG_ENDIAN_MMIO
---help---
Xilinx xps USB host controller core is EHCI compilant and has
transaction translator built-in. It can be configured to either
support both high speed and full speed devices, or high speed
devices only.
config USB_FSL_MPH_DR_OF
tristate
config USB_EHCI_FSL
bool "Support for Freescale on-chip EHCI USB controller"
depends on USB_EHCI_HCD && FSL_SOC
select USB_EHCI_ROOT_HUB_TT
select USB_FSL_MPH_DR_OF if OF
---help---
Variation of ARC USB block used in some Freescale chips.
config USB_EHCI_MXC
bool "Support for Freescale on-chip EHCI USB controller"
depends on USB_EHCI_HCD && ARCH_MXC
select USB_EHCI_ROOT_HUB_TT
---help---
Variation of ARC USB block used in some Freescale chips.
config USB_EHCI_HCD_OMAP
bool "EHCI support for OMAP3 and later chips"
depends on USB_EHCI_HCD && ARCH_OMAP
default y
--- help ---
Enables support for the on-chip EHCI controller on
OMAP3 and later chips.
config USB_EHCI_MSM
bool "Support for MSM on-chip EHCI USB controller"
depends on USB_EHCI_HCD && ARCH_MSM
select USB_EHCI_ROOT_HUB_TT
select USB_MSM_OTG
---help---
Enables support for the USB Host controller present on the
Qualcomm chipsets. Root Hub has inbuilt TT.
This driver depends on OTG driver for PHY initialization,
clock management, powering up VBUS, and power management.
This driver is not supported on boards like trout which
has an external PHY.
config USB_EHCI_TEGRA
boolean "NVIDIA Tegra HCD support"
depends on USB_EHCI_HCD && ARCH_TEGRA
select USB_EHCI_ROOT_HUB_TT
help
This driver enables support for the internal USB Host Controllers
found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
config USB_EHCI_HCD_PPC_OF
bool "EHCI support for PPC USB controller on OF platform bus"
depends on USB_EHCI_HCD && PPC_OF
default y
---help---
Enables support for the USB controller present on the PowerPC
OpenFirmware platform bus.
config USB_EHCI_SH
bool "EHCI support for SuperH USB controller"
depends on USB_EHCI_HCD && SUPERH
---help---
Enables support for the on-chip EHCI controller on the SuperH.
If you use the PCI EHCI controller, this option is not necessary.
config USB_EHCI_S5P
boolean "S5P EHCI support"
depends on USB_EHCI_HCD && PLAT_S5P
help
Enable support for the S5P SOC's on-chip EHCI controller.
config USB_W90X900_EHCI
bool "W90X900(W90P910) EHCI support"
depends on USB_EHCI_HCD && ARCH_W90X900
---help---
Enables support for the W90X900 USB controller
config USB_CNS3XXX_EHCI
bool "Cavium CNS3XXX EHCI Module"
depends on USB_EHCI_HCD && ARCH_CNS3XXX
---help---
Enable support for the CNS3XXX SOC's on-chip EHCI controller.
It is needed for high-speed (480Mbit/sec) USB 2.0 device
support.
config USB_EHCI_ATH79
bool "EHCI support for AR7XXX/AR9XXX SoCs"
depends on USB_EHCI_HCD && (SOC_AR71XX || SOC_AR724X || SOC_AR913X)
select USB_EHCI_ROOT_HUB_TT
default y
---help---
Enables support for the built-in EHCI controller present
on the Atheros AR7XXX/AR9XXX SoCs.
config USB_OXU210HP_HCD
tristate "OXU210HP HCD support"
depends on USB
---help---
The OXU210HP is an USB host/OTG/device controller. Enable this
option if your board has this chip. If unsure, say N.
This driver does not support isochronous transfers and doesn't
implement OTG nor USB device controllers.
To compile this driver as a module, choose M here: the
module will be called oxu210hp-hcd.
config USB_ISP116X_HCD
tristate "ISP116X HCD support"
depends on USB
---help---
The ISP1160 and ISP1161 chips are USB host controllers. Enable this
option if your board has this chip. If unsure, say N.
This driver does not support isochronous transfers.
To compile this driver as a module, choose M here: the
module will be called isp116x-hcd.
config USB_ISP1760_HCD
tristate "ISP 1760 HCD support"
depends on USB && EXPERIMENTAL
---help---
The ISP1760 chip is a USB 2.0 host controller.
This driver does not support isochronous transfers or OTG.
This USB controller is usually attached to a non-DMA-Master
capable bus. NXP's eval kit brings this chip on PCI card
where the chip itself is behind a PLB to simulate such
a bus.
To compile this driver as a module, choose M here: the
module will be called isp1760.
config USB_ISP1362_HCD
tristate "ISP1362 HCD support"
depends on USB
default N
---help---
Supports the Philips ISP1362 chip as a host controller
This driver does not support isochronous transfers.
To compile this driver as a module, choose M here: the
module will be called isp1362-hcd.
config USB_OHCI_HCD
tristate "OHCI HCD support"
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
select USB_OTG_UTILS if ARCH_OMAP
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
UHCI specification. If your USB host controller follows the OHCI spec,
say Y. On most non-x86 systems, and on x86 hardware that's not using a
USB controller from Intel or VIA, this is appropriate. If your host
controller doesn't use PCI, this is probably appropriate. For a PCI
based system where you're not sure, the "lspci -v" entry will list the
right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
To compile this driver as a module, choose M here: the
module will be called ohci-hcd.
config USB_OHCI_HCD_OMAP1
bool "OHCI support for OMAP1/2 chips"
depends on USB_OHCI_HCD && (ARCH_OMAP1 || ARCH_OMAP2)
default y
---help---
Enables support for the OHCI controller on OMAP1/2 chips.
config USB_OHCI_HCD_OMAP3
bool "OHCI support for OMAP3 and later chips"
depends on USB_OHCI_HCD && (ARCH_OMAP3 || ARCH_OMAP4)
default y
---help---
Enables support for the on-chip OHCI controller on
OMAP3 and later chips.
config USB_OHCI_ATH79
bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs"
depends on USB_OHCI_HCD && (SOC_AR71XX || SOC_AR724X)
default y
help
Enables support for the built-in OHCI controller present on the
Atheros AR71XX/AR7240 SoCs.
config USB_OHCI_HCD_PPC_SOC
bool "OHCI support for on-chip PPC USB controller"
depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
default y
select USB_OHCI_BIG_ENDIAN_DESC
select USB_OHCI_BIG_ENDIAN_MMIO
---help---
Enables support for the USB controller on the MPC52xx or
STB03xxx processor chip. If unsure, say Y.
config USB_OHCI_HCD_PPC_OF_BE
bool "OHCI support for OF platform bus (big endian)"
depends on USB_OHCI_HCD && PPC_OF
select USB_OHCI_BIG_ENDIAN_DESC
select USB_OHCI_BIG_ENDIAN_MMIO
---help---
Enables support for big-endian USB controllers present on the
OpenFirmware platform bus.
config USB_OHCI_HCD_PPC_OF_LE
bool "OHCI support for OF platform bus (little endian)"
depends on USB_OHCI_HCD && PPC_OF
select USB_OHCI_LITTLE_ENDIAN
---help---
Enables support for little-endian USB controllers present on the
OpenFirmware platform bus.
config USB_OHCI_HCD_PPC_OF
bool
depends on USB_OHCI_HCD && PPC_OF
default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
config USB_OHCI_HCD_PCI
bool "OHCI support for PCI-bus USB controllers"
depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
default y
select USB_OHCI_LITTLE_ENDIAN
---help---
Enables support for PCI-bus plug-in USB controller cards.
If unsure, say Y.
config USB_OHCI_HCD_SSB
bool "OHCI support for Broadcom SSB OHCI core"
depends on USB_OHCI_HCD && (SSB = y || SSB = USB_OHCI_HCD) && EXPERIMENTAL
default n
---help---
Support for the Sonics Silicon Backplane (SSB) attached
Broadcom USB OHCI core.
This device is present in some embedded devices with
Broadcom based SSB bus.
If unsure, say N.
config USB_OHCI_SH
bool "OHCI support for SuperH USB controller"
depends on USB_OHCI_HCD && SUPERH
---help---
Enables support for the on-chip OHCI controller on the SuperH.
If you use the PCI OHCI controller, this option is not necessary.
config USB_CNS3XXX_OHCI
bool "Cavium CNS3XXX OHCI Module"
depends on USB_OHCI_HCD && ARCH_CNS3XXX
---help---
Enable support for the CNS3XXX SOC's on-chip OHCI controller.
It is needed for low-speed USB 1.0 device support.
config USB_OHCI_BIG_ENDIAN_DESC
bool
depends on USB_OHCI_HCD
default n
config USB_OHCI_BIG_ENDIAN_MMIO
bool
depends on USB_OHCI_HCD
default n
config USB_OHCI_LITTLE_ENDIAN
bool
depends on USB_OHCI_HCD
default n if STB03xxx || PPC_MPC52xx
default y
config USB_UHCI_HCD
tristate "UHCI HCD (most Intel and VIA) support"
depends on USB && (PCI || SPARC_LEON)
---help---
The Universal Host Controller Interface is a standard by Intel for
accessing the USB hardware in the PC (which is also called the USB
host controller). If your USB host controller conforms to this
standard, you may want to say Y, but see below. All recent boards
with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
i810, i820) conform to this standard. Also all VIA PCI chipsets
(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
133) and LEON/GRLIB SoCs with the GRUSBHC controller.
If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called uhci-hcd.
config USB_UHCI_SUPPORT_NON_PCI_HC
bool
depends on USB_UHCI_HCD
default y if SPARC_LEON
config USB_UHCI_BIG_ENDIAN_MMIO
bool
depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
default y
config USB_UHCI_BIG_ENDIAN_DESC
bool
depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
default y
config USB_FHCI_HCD
tristate "Freescale QE USB Host Controller support"
depends on USB && OF_GPIO && QE_GPIO && QUICC_ENGINE
select FSL_GTM
select QE_USB
help
This driver enables support for Freescale QE USB Host Controller
(as found on MPC8360 and MPC8323 processors), the driver supports
Full and Low Speed USB.
config FHCI_DEBUG
bool "Freescale QE USB Host Controller debug support"
depends on USB_FHCI_HCD && DEBUG_FS
help
Say "y" to see some FHCI debug information and statistics
through debugfs.
config USB_U132_HCD
tristate "Elan U132 Adapter Host Controller"
depends on USB && USB_FTDI_ELAN
default M
help
The U132 adapter is a USB to CardBus adapter specifically designed
for PC cards that contain an OHCI host controller. Typical PC cards
are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
adapter will *NOT* work with PC cards that do not contain an OHCI
controller.
For those PC cards that contain multiple OHCI controllers only the
first one is used.
The driver consists of two modules, the "ftdi-elan" module is a
USB client driver that interfaces to the FTDI chip within ELAN's
USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
controller driver that talks to the OHCI controller within the
CardBus cards that are inserted in the U132 adapter.
This driver has been tested with a CardBus OHCI USB adapter, and
worked with a USB PEN Drive inserted into the first USB port of
the PCCARD. A rather pointless thing to do, but useful for testing.
It is safe to say M here.
See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
config USB_SL811_HCD
tristate "SL811HS HCD support"
depends on USB
help
The SL811HS is a single-port USB controller that supports either
host side or peripheral side roles. Enable this option if your
board has this chip, and you want to use it as a host controller.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called sl811-hcd.
config USB_SL811_HCD_ISO
bool "partial ISO support"
depends on USB_SL811_HCD
help
The driver doesn't support iso_frame_desc (yet), but for some simple
devices that just queue one ISO frame per URB, then ISO transfers
"should" work using the normal urb status fields.
If unsure, say N.
config USB_SL811_CS
tristate "CF/PCMCIA support for SL811HS HCD"
depends on USB_SL811_HCD && PCMCIA
help
Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
REX-CFU1U CF card (often used with PDAs). If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called "sl811_cs".
config USB_R8A66597_HCD
tristate "R8A66597 HCD support"
depends on USB
help
The R8A66597 is a USB 2.0 host and peripheral controller.
Enable this option if your board has this chip, and you want
to use it as a host controller. If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called r8a66597-hcd.
config USB_WHCI_HCD
tristate "Wireless USB Host Controller Interface (WHCI) driver (EXPERIMENTAL)"
depends on EXPERIMENTAL
depends on PCI && USB
select USB_WUSB
select UWB_WHCI
help
A driver for PCI-based Wireless USB Host Controllers that are
compliant with the WHCI specification.
To compile this driver a module, choose M here: the module
will be called "whci-hcd".
config USB_HWA_HCD
tristate "Host Wire Adapter (HWA) driver (EXPERIMENTAL)"
depends on EXPERIMENTAL
depends on USB
select USB_WUSB
select UWB_HWA
help
This driver enables you to connect Wireless USB devices to
your system using a Host Wire Adaptor USB dongle. This is an
UWB Radio Controller and WUSB Host Controller connected to
your machine via USB (specified in WUSB1.0).
To compile this driver a module, choose M here: the module
will be called "hwa-hc".
config USB_IMX21_HCD
tristate "iMX21 HCD support"
depends on USB && ARM && MACH_MX21
help
This driver enables support for the on-chip USB host in the
iMX21 processor.
To compile this driver as a module, choose M here: the
module will be called "imx21-hcd".
config USB_OCTEON_EHCI
bool "Octeon on-chip EHCI support"
depends on USB && USB_EHCI_HCD && CPU_CAVIUM_OCTEON
default n
select USB_EHCI_BIG_ENDIAN_MMIO
help
Enable support for the Octeon II SOC's on-chip EHCI
controller. It is needed for high-speed (480Mbit/sec)
USB 2.0 device support. All CN6XXX based chips with USB are
supported.
config USB_OCTEON_OHCI
bool "Octeon on-chip OHCI support"
depends on USB && USB_OHCI_HCD && CPU_CAVIUM_OCTEON
default USB_OCTEON_EHCI
select USB_OHCI_BIG_ENDIAN_MMIO
select USB_OHCI_LITTLE_ENDIAN
help
Enable support for the Octeon II SOC's on-chip OHCI
controller. It is needed for low-speed USB 1.0 device
support. All CN6XXX based chips with USB are supported.
config USB_OCTEON2_COMMON
bool
default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
View Git Blame Copy Permalink