mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 14:43:58 +08:00
20353143a2
Allows to use the SD interface at a higher speed mode if the card supports it. For this the signaling voltage is switched from 3.3V to 1.8V under the usdhc1's drivers control. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
165 lines
2.8 KiB
Plaintext
165 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
/*
|
|
* Copyright 2017 Toradex AG
|
|
*/
|
|
|
|
/ {
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
/* fixed crystal dedicated to mcp2515 */
|
|
clk16m: clk16m {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <16000000>;
|
|
};
|
|
|
|
panel: panel {
|
|
compatible = "edt,et057090dhu";
|
|
backlight = <&bl>;
|
|
power-supply = <®_3v3>;
|
|
|
|
port {
|
|
panel_in: endpoint {
|
|
remote-endpoint = <&lcdif_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
reg_3v3: regulator-3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
reg_5v0: regulator-5v0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
};
|
|
|
|
reg_usbh_vbus: regulator-usbh-vbus {
|
|
compatible = "regulator-fixed";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usbh_reg>;
|
|
regulator-name = "VCC_USB[1-4]";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
|
|
vin-supply = <®_5v0>;
|
|
};
|
|
};
|
|
|
|
&adc1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&bl {
|
|
brightness-levels = <0 4 8 16 32 64 128 255>;
|
|
default-brightness-level = <6>;
|
|
power-supply = <®_3v3>;
|
|
pwms = <&pwm4 0 5000000 1>;
|
|
status = "okay";
|
|
};
|
|
|
|
&ecspi1 {
|
|
status = "okay";
|
|
|
|
mcp2515: can@0 {
|
|
compatible = "microchip,mcp2515";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_can_int>;
|
|
reg = <0>;
|
|
clocks = <&clk16m>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
|
spi-max-frequency = <10000000>;
|
|
vdd-supply = <®_3v3>;
|
|
xceiver-supply = <®_5v0>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
|
|
/* M41T0M6 real time clock on carrier board */
|
|
m41t0m6: rtc@68 {
|
|
compatible = "st,m41t0";
|
|
reg = <0x68>;
|
|
};
|
|
};
|
|
|
|
&lcdif {
|
|
status = "okay";
|
|
|
|
port {
|
|
lcdif_out: endpoint {
|
|
remote-endpoint = <&panel_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/* PWM <A> */
|
|
&pwm4 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* PWM <B> */
|
|
&pwm5 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* PWM <C> */
|
|
&pwm6 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* PWM <D> */
|
|
&pwm7 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart5 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg2 {
|
|
vbus-supply = <®_usbh_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc1 {
|
|
pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
|
|
pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
|
|
pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
|
|
pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
|
|
pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
|
|
cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
|
|
disable-wp;
|
|
wakeup-source;
|
|
keep-power-in-suspend;
|
|
vmmc-supply = <®_3v3>;
|
|
vqmmc-supply = <®_sd1_vmmc>;
|
|
sd-uhs-sdr12;
|
|
sd-uhs-sdr25;
|
|
sd-uhs-sdr50;
|
|
sd-uhs-sdr104;
|
|
status = "okay";
|
|
};
|