renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 04:34:11 +08:00
Code
bf992fa2bc
linux-next/arch/arm/mach-orion5x/mss2-setup.c
Thomas Reitmayr 6462c6160a [ARM] orion5x: Change names of defines for Reset-Out-Mask register 
The name of the define for the Reset-Out-Mask register as well as its
bit for the watchdog reset are changed to match the names used for
Kirkwood (which in turn match the processor specification more
closely). There is no functional change.

This patch prepares for adding orion5x_wdt as a platform device to
Kirkwood.

Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2009-06-08 13:04:59 -04:00

273 lines
7.1 KiB
C
Raw Blame History

/*
* Maxtor Shared Storage II Board Setup
*
* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/leds.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include <mach/bridge-regs.h>
#include "common.h"
#include "mpp.h"
#define MSS2_NOR_BOOT_BASE 0xff800000
#define MSS2_NOR_BOOT_SIZE SZ_256K
/*****************************************************************************
* Maxtor Shared Storage II Info
****************************************************************************/
/*
* Maxtor Shared Storage II hardware :
* - Marvell 88F5182-A2 C500
* - Marvell 88E1111 Gigabit Ethernet PHY
* - RTC M41T81 (@0x68) on I2C bus
* - 256KB NOR flash
* - 64MB of RAM
*/
/*****************************************************************************
* 256KB NOR Flash on BOOT Device
****************************************************************************/
static struct physmap_flash_data mss2_nor_flash_data = {
.width = 1,
};
static struct resource mss2_nor_flash_resource = {
.flags = IORESOURCE_MEM,
.start = MSS2_NOR_BOOT_BASE,
.end = MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
};
static struct platform_device mss2_nor_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &mss2_nor_flash_data,
},
.resource = &mss2_nor_flash_resource,
.num_resources = 1,
};
/****************************************************************************
* PCI setup
****************************************************************************/
static int __init mss2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
int irq;
/*
* Check for devices with hard-wired IRQs.
*/
irq = orion5x_pci_map_irq(dev, slot, pin);
if (irq != -1)
return irq;
return -1;
}
static struct hw_pci mss2_pci __initdata = {
.nr_controllers = 2,
.swizzle = pci_std_swizzle,
.setup = orion5x_pci_sys_setup,
.scan = orion5x_pci_sys_scan_bus,
.map_irq = mss2_pci_map_irq,
};
static int __init mss2_pci_init(void)
{
if (machine_is_mss2())
pci_common_init(&mss2_pci);
return 0;
}
subsys_initcall(mss2_pci_init);
/*****************************************************************************
* Ethernet
****************************************************************************/
static struct mv643xx_eth_platform_data mss2_eth_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
};
/*****************************************************************************
* SATA
****************************************************************************/
static struct mv_sata_platform_data mss2_sata_data = {
.n_ports = 2,
};
/*****************************************************************************
* GPIO buttons
****************************************************************************/
#define MSS2_GPIO_KEY_RESET 12
#define MSS2_GPIO_KEY_POWER 11
static struct gpio_keys_button mss2_buttons[] = {
{
.code = KEY_POWER,
.gpio = MSS2_GPIO_KEY_POWER,
.desc = "Power",
.active_low = 1,
}, {
.code = KEY_RESTART,
.gpio = MSS2_GPIO_KEY_RESET,
.desc = "Reset",
.active_low = 1,
},
};
static struct gpio_keys_platform_data mss2_button_data = {
.buttons = mss2_buttons,
.nbuttons = ARRAY_SIZE(mss2_buttons),
};
static struct platform_device mss2_button_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &mss2_button_data,
},
};
/*****************************************************************************
* RTC m41t81 on I2C bus
****************************************************************************/
#define MSS2_GPIO_RTC_IRQ 3
static struct i2c_board_info __initdata mss2_i2c_rtc = {
I2C_BOARD_INFO("m41t81", 0x68),
};
/*****************************************************************************
* MSS2 power off method
****************************************************************************/
/*
* On the Maxtor Shared Storage II, the shutdown process is the following :
* - Userland modifies U-boot env to tell U-boot to go idle at next boot
* - The board reboots
* - U-boot starts and go into an idle mode until the user press "power"
*/
static void mss2_power_off(void)
{
u32 reg;
/*
* Enable and issue soft reset
*/
reg = readl(RSTOUTn_MASK);
reg |= 1 << 2;
writel(reg, RSTOUTn_MASK);
reg = readl(CPU_SOFT_RESET);
reg |= 1;
writel(reg, CPU_SOFT_RESET);
}
/****************************************************************************
* General Setup
****************************************************************************/
static struct orion5x_mpp_mode mss2_mpp_modes[] __initdata = {
{ 0, MPP_GPIO }, /* Power LED */
{ 1, MPP_GPIO }, /* Error LED */
{ 2, MPP_UNUSED },
{ 3, MPP_GPIO }, /* RTC interrupt */
{ 4, MPP_GPIO }, /* HDD ind. (Single/Dual)*/
{ 5, MPP_GPIO }, /* HD0 5V control */
{ 6, MPP_GPIO }, /* HD0 12V control */
{ 7, MPP_GPIO }, /* HD1 5V control */
{ 8, MPP_GPIO }, /* HD1 12V control */
{ 9, MPP_UNUSED },
{ 10, MPP_GPIO }, /* Fan control */
{ 11, MPP_GPIO }, /* Power button */
{ 12, MPP_GPIO }, /* Reset button */
{ 13, MPP_UNUSED },
{ 14, MPP_SATA_LED }, /* SATA 0 active */
{ 15, MPP_SATA_LED }, /* SATA 1 active */
{ 16, MPP_UNUSED },
{ 17, MPP_UNUSED },
{ 18, MPP_UNUSED },
{ 19, MPP_UNUSED },
{ -1 },
};
static void __init mss2_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
orion5x_mpp_conf(mss2_mpp_modes);
/*
* MPP[20] Unused
* MPP[21] PCI clock
* MPP[22] USB 0 over current
* MPP[23] USB 1 over current
*/
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&mss2_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&mss2_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(MSS2_NOR_BOOT_BASE, MSS2_NOR_BOOT_SIZE);
platform_device_register(&mss2_nor_flash);
platform_device_register(&mss2_button_device);
if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
else
gpio_free(MSS2_GPIO_RTC_IRQ);
}
i2c_register_board_info(0, &mss2_i2c_rtc, 1);
/* register mss2 specific power-off method */
pm_power_off = mss2_power_off;
}
MACHINE_START(MSS2, "Maxtor Shared Storage II")
/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
.phys_io = ORION5X_REGS_PHYS_BASE,
.io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.init_machine = mss2_init,
.map_io = orion5x_map_io,
.init_irq = orion5x_init_irq,
.timer = &orion5x_timer,
.fixup = tag_fixup_mem32
MACHINE_END
View Git Blame Copy Permalink