mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 04:34:11 +08:00
3ad418e0f0
The common mmc DT parser supports bindings for highspeed mode, thus there are no need for mmci to provide it's own versions for these. Mark them as deprecated in the documentation. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Rob Herring <robh@kernel.org>
62 lines
2.2 KiB
Plaintext
62 lines
2.2 KiB
Plaintext
* ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1
|
|
|
|
The ARM PrimeCell MMCI PL180 and PL181 provides an interface for
|
|
reading and writing to MultiMedia and SD cards alike.
|
|
|
|
This file documents differences between the core properties described
|
|
by mmc.txt and the properties used by the mmci driver. Using "st" as
|
|
the prefix for a property, indicates support by the ST Micro variant.
|
|
|
|
Required properties:
|
|
- compatible : contains "arm,pl18x", "arm,primecell".
|
|
- vmmc-supply : phandle to the regulator device tree node, mentioned
|
|
as the VCC/VDD supply in the eMMC/SD specs.
|
|
|
|
Optional properties:
|
|
- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides
|
|
the ID provided by the HW
|
|
- vqmmc-supply : phandle to the regulator device tree node, mentioned
|
|
as the VCCQ/VDD_IO supply in the eMMC/SD specs.
|
|
- st,sig-dir-dat0 : bus signal direction pin used for DAT[0].
|
|
- st,sig-dir-dat2 : bus signal direction pin used for DAT[2].
|
|
- st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1].
|
|
- st,sig-dir-dat74 : bus signal direction pin used for DAT[4] to DAT[7].
|
|
- st,sig-dir-cmd : cmd signal direction pin used for CMD.
|
|
- st,sig-pin-fbclk : feedback clock signal pin used.
|
|
|
|
Deprecated properties:
|
|
- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable.
|
|
- mmc-cap-sd-highspeed : indicates whether SD is high speed capable.
|
|
|
|
Example:
|
|
|
|
sdi0_per1@80126000 {
|
|
compatible = "arm,pl18x", "arm,primecell";
|
|
reg = <0x80126000 0x1000>;
|
|
interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */
|
|
<&dma 29 0 0x0>; /* Logical - MemToDev */
|
|
dma-names = "rx", "tx";
|
|
|
|
clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
|
|
clock-names = "sdi", "apb_pclk";
|
|
|
|
max-frequency = <100000000>;
|
|
bus-width = <4>;
|
|
cap-sd-highspeed;
|
|
cap-mmc-highspeed;
|
|
cd-gpios = <&gpio2 31 0x4>; // 95
|
|
st,sig-dir-dat0;
|
|
st,sig-dir-dat2;
|
|
st,sig-dir-cmd;
|
|
st,sig-pin-fbclk;
|
|
|
|
vmmc-supply = <&ab8500_ldo_aux3_reg>;
|
|
vqmmc-supply = <&vmmci>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdi0_default_mode>;
|
|
pinctrl-1 = <&sdi0_sleep_mode>;
|
|
};
|