mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-28 07:04:00 +08:00
138b15ed87
This howto made sense in the 1990s when users had to manually configure ISA cards with jumpers or vendor utilities, but with the implementation of PCI it became increasingly less and less relevant, to the point where it has been well over a decade since I last updated it. And there is no value in anyone else taking over updating it either. However the references to it continue to spread as boiler plate text from one Kconfig file into the next. We are not doing end users any favours by pointing them at this old document, so lets kill it with fire, once and for all, to hopefully stop any further spread. No code is changed in this commit, just Kconfig help text. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
65 lines
1.7 KiB
Plaintext
65 lines
1.7 KiB
Plaintext
#
|
|
# Micrel device configuration
|
|
#
|
|
|
|
config NET_VENDOR_MICREL
|
|
bool "Micrel devices"
|
|
default y
|
|
depends on (HAS_IOMEM && DMA_ENGINE) || SPI || PCI || HAS_IOMEM || \
|
|
(ARM && ARCH_KS8695)
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Micrel devices. If you say Y, you will be asked
|
|
for your specific card in the following questions.
|
|
|
|
if NET_VENDOR_MICREL
|
|
|
|
config ARM_KS8695_ETHER
|
|
tristate "KS8695 Ethernet support"
|
|
depends on ARM && ARCH_KS8695
|
|
select MII
|
|
---help---
|
|
If you wish to compile a kernel for the KS8695 and want to
|
|
use the internal ethernet then you should answer Y to this.
|
|
|
|
config KS8842
|
|
tristate "Micrel KSZ8841/42 with generic bus interface"
|
|
depends on HAS_IOMEM && DMA_ENGINE
|
|
---help---
|
|
This platform driver is for KSZ8841(1-port) / KS8842(2-port)
|
|
ethernet switch chip (managed, VLAN, QoS) from Micrel or
|
|
Timberdale(FPGA).
|
|
|
|
config KS8851
|
|
tristate "Micrel KS8851 SPI"
|
|
depends on SPI
|
|
select MII
|
|
select CRC32
|
|
select EEPROM_93CX6
|
|
---help---
|
|
SPI driver for Micrel KS8851 SPI attached network chip.
|
|
|
|
config KS8851_MLL
|
|
tristate "Micrel KS8851 MLL"
|
|
depends on HAS_IOMEM
|
|
select MII
|
|
---help---
|
|
This platform driver is for Micrel KS8851 Address/data bus
|
|
multiplexed network chip.
|
|
|
|
config KSZ884X_PCI
|
|
tristate "Micrel KSZ8841/2 PCI"
|
|
depends on PCI
|
|
select MII
|
|
select CRC32
|
|
---help---
|
|
This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called ksz884x.
|
|
|
|
endif # NET_VENDOR_MICREL
|