renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-27 06:34:11 +08:00
Code
a7d57abcc8
linux-next/drivers/usb/host/xhci-rcar.c
Yoshihiro Shimoda 5f9810730c usb: host: xhci-rcar: Add a condition check about PLL active 
This patch adds a condition check about the PLL acvice of this
controller. Otherwise, the controller might cause hang when
any USB clocks are not supplied yet and accesses the xHCI registers.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-06 16:37:19 +02:00

262 lines
7.3 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* xHCI host controller driver for R-Car SoCs
*
* Copyright (C) 2014 Renesas Electronics Corporation
*/
#include <linux/firmware.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/usb/phy.h>
#include <linux/sys_soc.h>
#include "xhci.h"
#include "xhci-plat.h"
#include "xhci-rcar.h"
/*
* - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x)
* - The V2 firmware is for r8a7795 ES1.x.
* - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
* performance degradation. So, this driver continues to use the V1 if R-Car
* Gen2.
* - The V1 firmware is impossible to use on R-Car Gen3.
*/
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3);
/*** Register Offset ***/
#define RCAR_USB3_AXH_STA 0x104 /* AXI Host Control Status */
#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */
#define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */
#define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */
#define RCAR_USB3_LCLK 0xa44 /* LCLK Select */
#define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */
#define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */
#define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */
#define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */
#define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */
/*** Register Settings ***/
/* AXI Host Control Status */
#define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE 0x00010000
#define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE 0x00000001
#define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \
RCAR_USB3_AXH_STA_B2_PLL_ACTIVE)
/* Interrupt Enable */
#define RCAR_USB3_INT_XHC_ENA 0x00000001
#define RCAR_USB3_INT_PME_ENA 0x00000002
#define RCAR_USB3_INT_HSE_ENA 0x00000004
#define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \
RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
/* FW Download Control & Status */
#define RCAR_USB3_DL_CTRL_ENABLE 0x00000001
#define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010
#define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100
/* LCLK Select */
#define RCAR_USB3_LCLK_ENA_VAL 0x01030001
/* USB3.0 Configuration */
#define RCAR_USB3_CONF1_VAL 0x00030204
#define RCAR_USB3_CONF2_VAL 0x00030300
#define RCAR_USB3_CONF3_VAL 0x13802007
/* USB3.0 Polarity */
#define RCAR_USB3_RX_POL_VAL BIT(21)
#define RCAR_USB3_TX_POL_VAL BIT(4)
/* For soc_device_attribute */
#define RCAR_XHCI_FIRMWARE_V2 BIT(0) /* FIRMWARE V2 */
#define RCAR_XHCI_FIRMWARE_V3 BIT(1) /* FIRMWARE V3 */
static const struct soc_device_attribute rcar_quirks_match[] = {
{
.soc_id = "r8a7795", .revision = "ES1.*",
.data = (void *)RCAR_XHCI_FIRMWARE_V2,
},
{ /* sentinel */ },
};
static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
{
/* LCLK Select */
writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
/* USB3.0 Configuration */
writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
/* USB3.0 Polarity */
writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
}
static int xhci_rcar_is_gen2(struct device *dev)
{
struct device_node *node = dev->of_node;
return of_device_is_compatible(node, "renesas,xhci-r8a7790") ||
of_device_is_compatible(node, "renesas,xhci-r8a7791") ||
of_device_is_compatible(node, "renesas,xhci-r8a7793") ||
of_device_is_compatible(node, "renensas,rcar-gen2-xhci");
}
static int xhci_rcar_is_gen3(struct device *dev)
{
struct device_node *node = dev->of_node;
return of_device_is_compatible(node, "renesas,xhci-r8a7795") ||
of_device_is_compatible(node, "renesas,xhci-r8a7796") ||
of_device_is_compatible(node, "renesas,rcar-gen3-xhci");
}
void xhci_rcar_start(struct usb_hcd *hcd)
{
u32 temp;
if (hcd->regs != NULL) {
/* Interrupt Enable */
temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
temp |= RCAR_USB3_INT_ENA_VAL;
writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
if (xhci_rcar_is_gen2(hcd->self.controller))
xhci_rcar_start_gen2(hcd);
}
}
static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
{
struct device *dev = hcd->self.controller;
void __iomem *regs = hcd->regs;
struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
const struct firmware *fw;
int retval, index, j, time;
int timeout = 10000;
u32 data, val, temp;
u32 quirks = 0;
const struct soc_device_attribute *attr;
const char *firmware_name;
attr = soc_device_match(rcar_quirks_match);
if (attr)
quirks = (uintptr_t)attr->data;
if (quirks & RCAR_XHCI_FIRMWARE_V2)
firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
else if (quirks & RCAR_XHCI_FIRMWARE_V3)
firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
else
firmware_name = priv->firmware_name;
/* request R-Car USB3.0 firmware */
retval = request_firmware(&fw, firmware_name, dev);
if (retval)
return retval;
/* download R-Car USB3.0 firmware */
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp |= RCAR_USB3_DL_CTRL_ENABLE;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (index = 0; index < fw->size; index += 4) {
/* to avoid reading beyond the end of the buffer */
for (data = 0, j = 3; j >= 0; j--) {
if ((j + index) < fw->size)
data |= fw->data[index + j] << (8 * j);
}
writel(data, regs + RCAR_USB3_FW_DATA0);
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (time = 0; time < timeout; time++) {
val = readl(regs + RCAR_USB3_DL_CTRL);
if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
break;
udelay(1);
}
if (time == timeout) {
retval = -ETIMEDOUT;
break;
}
}
temp = readl(regs + RCAR_USB3_DL_CTRL);
temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
writel(temp, regs + RCAR_USB3_DL_CTRL);
for (time = 0; time < timeout; time++) {
val = readl(regs + RCAR_USB3_DL_CTRL);
if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
retval = 0;
break;
}
udelay(1);
}
if (time == timeout)
retval = -ETIMEDOUT;
release_firmware(fw);
return retval;
}
static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd)
{
int timeout = 1000;
u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK;
while (timeout > 0) {
val = readl(hcd->regs + RCAR_USB3_AXH_STA);
if ((val & mask) == mask)
return true;
udelay(1);
timeout--;
}
return false;
}
/* This function needs to initialize a "phy" of usb before */
int xhci_rcar_init_quirk(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
/* If hcd->regs is NULL, we don't just call the following function */
if (!hcd->regs)
return 0;
/*
* On R-Car Gen2 and Gen3, the AC64 bit (bit 0) of HCCPARAMS1 is set
* to 1. However, these SoCs don't support 64-bit address memory
* pointers. So, this driver clears the AC64 bit of xhci->hcc_params
* to call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in
* xhci_gen_setup().
*/
if (xhci_rcar_is_gen2(hcd->self.controller) ||
xhci_rcar_is_gen3(hcd->self.controller))
xhci->quirks |= XHCI_NO_64BIT_SUPPORT;
if (!xhci_rcar_wait_for_pll_active(hcd))
return -ETIMEDOUT;
return xhci_rcar_download_firmware(hcd);
}
int xhci_rcar_resume_quirk(struct usb_hcd *hcd)
{
int ret;
ret = xhci_rcar_download_firmware(hcd);
if (!ret)
xhci_rcar_start(hcd);
return ret;
}
View Git Blame Copy Permalink