renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 20:53:53 +08:00
Code
a19f5df7d9
linux-next/drivers/ata/libata-sff.c
Tejun Heo 6a6b97d360 libata: improve phantom device detection 
Currently libata uses four methods to detect device presence.

1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine

Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe.  In both cases, PHY status wasn't available.  In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4.  The other failed #2 but as it passed #3 and #4,
it still caused failure.

In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14 18:51:57 -05:00

2877 lines
73 KiB
C
Raw Blame History

/*
* libata-sff.c - helper library for PCI IDE BMDMA
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
* Copyright 2003-2006 Red Hat, Inc. All rights reserved.
* Copyright 2003-2006 Jeff Garzik
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* Hardware documentation available from http://www.t13.org/ and
* http://www.sata-io.org/
*
*/
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/libata.h>
#include <linux/highmem.h>
#include "libata.h"
const struct ata_port_operations ata_sff_port_ops = {
.inherits = &ata_base_port_ops,
.qc_prep = ata_sff_qc_prep,
.qc_issue = ata_sff_qc_issue,
.qc_fill_rtf = ata_sff_qc_fill_rtf,
.freeze = ata_sff_freeze,
.thaw = ata_sff_thaw,
.prereset = ata_sff_prereset,
.softreset = ata_sff_softreset,
.hardreset = sata_sff_hardreset,
.postreset = ata_sff_postreset,
.error_handler = ata_sff_error_handler,
.post_internal_cmd = ata_sff_post_internal_cmd,
.sff_dev_select = ata_sff_dev_select,
.sff_check_status = ata_sff_check_status,
.sff_tf_load = ata_sff_tf_load,
.sff_tf_read = ata_sff_tf_read,
.sff_exec_command = ata_sff_exec_command,
.sff_data_xfer = ata_sff_data_xfer,
.sff_irq_on = ata_sff_irq_on,
.sff_irq_clear = ata_sff_irq_clear,
.port_start = ata_sff_port_start,
};
const struct ata_port_operations ata_bmdma_port_ops = {
.inherits = &ata_sff_port_ops,
.mode_filter = ata_bmdma_mode_filter,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
};
/**
* ata_fill_sg - Fill PCI IDE PRD table
* @qc: Metadata associated with taskfile to be transferred
*
* Fill PCI IDE PRD (scatter-gather) table with segments
* associated with the current disk command.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
*/
static void ata_fill_sg(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
unsigned int si, pi;
pi = 0;
for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len;
/* determine if physical DMA addr spans 64K boundary.
* Note h/w doesn't support 64-bit, so we unconditionally
* truncate dma_addr_t to u32.
*/
addr = (u32) sg_dma_address(sg);
sg_len = sg_dma_len(sg);
while (sg_len) {
offset = addr & 0xffff;
len = sg_len;
if ((offset + sg_len) > 0x10000)
len = 0x10000 - offset;
ap->prd[pi].addr = cpu_to_le32(addr);
ap->prd[pi].flags_len = cpu_to_le32(len & 0xffff);
VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
pi++;
sg_len -= len;
addr += len;
}
}
ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
/**
* ata_fill_sg_dumb - Fill PCI IDE PRD table
* @qc: Metadata associated with taskfile to be transferred
*
* Fill PCI IDE PRD (scatter-gather) table with segments
* associated with the current disk command. Perform the fill
* so that we avoid writing any length 64K records for
* controllers that don't follow the spec.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
*/
static void ata_fill_sg_dumb(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
unsigned int si, pi;
pi = 0;
for_each_sg(qc->sg, sg, qc->n_elem, si) {
u32 addr, offset;
u32 sg_len, len, blen;
/* determine if physical DMA addr spans 64K boundary.
* Note h/w doesn't support 64-bit, so we unconditionally
* truncate dma_addr_t to u32.
*/
addr = (u32) sg_dma_address(sg);
sg_len = sg_dma_len(sg);
while (sg_len) {
offset = addr & 0xffff;
len = sg_len;
if ((offset + sg_len) > 0x10000)
len = 0x10000 - offset;
blen = len & 0xffff;
ap->prd[pi].addr = cpu_to_le32(addr);
if (blen == 0) {
/* Some PATA chipsets like the CS5530 can't
cope with 0x0000 meaning 64K as the spec says */
ap->prd[pi].flags_len = cpu_to_le32(0x8000);
blen = 0x8000;
ap->prd[++pi].addr = cpu_to_le32(addr + 0x8000);
}
ap->prd[pi].flags_len = cpu_to_le32(blen);
VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", pi, addr, len);
pi++;
sg_len -= len;
addr += len;
}
}
ap->prd[pi - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
/**
* ata_sff_qc_prep - Prepare taskfile for submission
* @qc: Metadata associated with taskfile to be prepared
*
* Prepare ATA taskfile for submission.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_sff_qc_prep(struct ata_queued_cmd *qc)
{
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
ata_fill_sg(qc);
}
/**
* ata_sff_dumb_qc_prep - Prepare taskfile for submission
* @qc: Metadata associated with taskfile to be prepared
*
* Prepare ATA taskfile for submission.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_sff_dumb_qc_prep(struct ata_queued_cmd *qc)
{
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
ata_fill_sg_dumb(qc);
}
/**
* ata_sff_check_status - Read device status reg & clear interrupt
* @ap: port where the device is
*
* Reads ATA taskfile status register for currently-selected device
* and return its value. This also clears pending interrupts
* from this device
*
* LOCKING:
* Inherited from caller.
*/
u8 ata_sff_check_status(struct ata_port *ap)
{
return ioread8(ap->ioaddr.status_addr);
}
/**
* ata_sff_altstatus - Read device alternate status reg
* @ap: port where the device is
*
* Reads ATA taskfile alternate status register for
* currently-selected device and return its value.
*
* Note: may NOT be used as the check_altstatus() entry in
* ata_port_operations.
*
* LOCKING:
* Inherited from caller.
*/
static u8 ata_sff_altstatus(struct ata_port *ap)
{
if (ap->ops->sff_check_altstatus)
return ap->ops->sff_check_altstatus(ap);
return ioread8(ap->ioaddr.altstatus_addr);
}
/**
* ata_sff_irq_status - Check if the device is busy
* @ap: port where the device is
*
* Determine if the port is currently busy. Uses altstatus
* if available in order to avoid clearing shared IRQ status
* when finding an IRQ source. Non ctl capable devices don't
* share interrupt lines fortunately for us.
*
* LOCKING:
* Inherited from caller.
*/
static u8 ata_sff_irq_status(struct ata_port *ap)
{
u8 status;
if (ap->ops->sff_check_altstatus || ap->ioaddr.altstatus_addr) {
status = ata_sff_altstatus(ap);
/* Not us: We are busy */
if (status & ATA_BUSY)
return status;
}
/* Clear INTRQ latch */
status = ap->ops->sff_check_status(ap);
return status;
}
/**
* ata_sff_sync - Flush writes
* @ap: Port to wait for.
*
* CAUTION:
* If we have an mmio device with no ctl and no altstatus
* method this will fail. No such devices are known to exist.
*
* LOCKING:
* Inherited from caller.
*/
static void ata_sff_sync(struct ata_port *ap)
{
if (ap->ops->sff_check_altstatus)
ap->ops->sff_check_altstatus(ap);
else if (ap->ioaddr.altstatus_addr)
ioread8(ap->ioaddr.altstatus_addr);
}
/**
* ata_sff_pause - Flush writes and wait 400nS
* @ap: Port to pause for.
*
* CAUTION:
* If we have an mmio device with no ctl and no altstatus
* method this will fail. No such devices are known to exist.
*
* LOCKING:
* Inherited from caller.
*/
void ata_sff_pause(struct ata_port *ap)
{
ata_sff_sync(ap);
ndelay(400);
}
/**
* ata_sff_dma_pause - Pause before commencing DMA
* @ap: Port to pause for.
*
* Perform I/O fencing and ensure sufficient cycle delays occur
* for the HDMA1:0 transition
*/
void ata_sff_dma_pause(struct ata_port *ap)
{
if (ap->ops->sff_check_altstatus || ap->ioaddr.altstatus_addr) {
/* An altstatus read will cause the needed delay without
messing up the IRQ status */
ata_sff_altstatus(ap);
return;
}
/* There are no DMA controllers without ctl. BUG here to ensure
we never violate the HDMA1:0 transition timing and risk
corruption. */
BUG();
}
/**
* ata_sff_busy_sleep - sleep until BSY clears, or timeout
* @ap: port containing status register to be polled
* @tmout_pat: impatience timeout in msecs
* @tmout: overall timeout in msecs
*
* Sleep until ATA Status register bit BSY clears,
* or a timeout occurs.
*
* LOCKING:
* Kernel thread context (may sleep).
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_sff_busy_sleep(struct ata_port *ap,
unsigned long tmout_pat, unsigned long tmout)
{
unsigned long timer_start, timeout;
u8 status;
status = ata_sff_busy_wait(ap, ATA_BUSY, 300);
timer_start = jiffies;
timeout = ata_deadline(timer_start, tmout_pat);
while (status != 0xff && (status & ATA_BUSY) &&
time_before(jiffies, timeout)) {
msleep(50);
status = ata_sff_busy_wait(ap, ATA_BUSY, 3);
}
if (status != 0xff && (status & ATA_BUSY))
ata_port_printk(ap, KERN_WARNING,
"port is slow to respond, please be patient "
"(Status 0x%x)\n", status);
timeout = ata_deadline(timer_start, tmout);
while (status != 0xff && (status & ATA_BUSY) &&
time_before(jiffies, timeout)) {
msleep(50);
status = ap->ops->sff_check_status(ap);
}
if (status == 0xff)
return -ENODEV;
if (status & ATA_BUSY) {
ata_port_printk(ap, KERN_ERR, "port failed to respond "
"(%lu secs, Status 0x%x)\n",
DIV_ROUND_UP(tmout, 1000), status);
return -EBUSY;
}
return 0;
}
static int ata_sff_check_ready(struct ata_link *link)
{
u8 status = link->ap->ops->sff_check_status(link->ap);
return ata_check_ready(status);
}
/**
* ata_sff_wait_ready - sleep until BSY clears, or timeout
* @link: SFF link to wait ready status for
* @deadline: deadline jiffies for the operation
*
* Sleep until ATA Status register bit BSY clears, or timeout
* occurs.
*
* LOCKING:
* Kernel thread context (may sleep).
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_sff_wait_ready(struct ata_link *link, unsigned long deadline)
{
return ata_wait_ready(link, deadline, ata_sff_check_ready);
}
/**
* ata_sff_dev_select - Select device 0/1 on ATA bus
* @ap: ATA channel to manipulate
* @device: ATA device (numbered from zero) to select
*
* Use the method defined in the ATA specification to
* make either device 0, or device 1, active on the
* ATA channel. Works with both PIO and MMIO.
*
* May be used as the dev_select() entry in ata_port_operations.
*
* LOCKING:
* caller.
*/
void ata_sff_dev_select(struct ata_port *ap, unsigned int device)
{
u8 tmp;
if (device == 0)
tmp = ATA_DEVICE_OBS;
else
tmp = ATA_DEVICE_OBS | ATA_DEV1;
iowrite8(tmp, ap->ioaddr.device_addr);
ata_sff_pause(ap); /* needed; also flushes, for mmio */
}
/**
* ata_dev_select - Select device 0/1 on ATA bus
* @ap: ATA channel to manipulate
* @device: ATA device (numbered from zero) to select
* @wait: non-zero to wait for Status register BSY bit to clear
* @can_sleep: non-zero if context allows sleeping
*
* Use the method defined in the ATA specification to
* make either device 0, or device 1, active on the
* ATA channel.
*
* This is a high-level version of ata_sff_dev_select(), which
* additionally provides the services of inserting the proper
* pauses and status polling, where needed.
*
* LOCKING:
* caller.
*/
void ata_dev_select(struct ata_port *ap, unsigned int device,
unsigned int wait, unsigned int can_sleep)
{
if (ata_msg_probe(ap))
ata_port_printk(ap, KERN_INFO, "ata_dev_select: ENTER, "
"device %u, wait %u\n", device, wait);
if (wait)
ata_wait_idle(ap);
ap->ops->sff_dev_select(ap, device);
if (wait) {
if (can_sleep && ap->link.device[device].class == ATA_DEV_ATAPI)
msleep(150);
ata_wait_idle(ap);
}
}
/**
* ata_sff_irq_on - Enable interrupts on a port.
* @ap: Port on which interrupts are enabled.
*
* Enable interrupts on a legacy IDE device using MMIO or PIO,
* wait for idle, clear any pending interrupts.
*
* LOCKING:
* Inherited from caller.
*/
u8 ata_sff_irq_on(struct ata_port *ap)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
u8 tmp;
ap->ctl &= ~ATA_NIEN;
ap->last_ctl = ap->ctl;
if (ioaddr->ctl_addr)
iowrite8(ap->ctl, ioaddr->ctl_addr);
tmp = ata_wait_idle(ap);
ap->ops->sff_irq_clear(ap);
return tmp;
}
/**
* ata_sff_irq_clear - Clear PCI IDE BMDMA interrupt.
* @ap: Port associated with this ATA transaction.
*
* Clear interrupt and error flags in DMA status register.
*
* May be used as the irq_clear() entry in ata_port_operations.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_sff_irq_clear(struct ata_port *ap)
{
void __iomem *mmio = ap->ioaddr.bmdma_addr;
if (!mmio)
return;
iowrite8(ioread8(mmio + ATA_DMA_STATUS), mmio + ATA_DMA_STATUS);
}
/**
* ata_sff_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
* @tf: ATA taskfile register set
*
* Outputs ATA taskfile to standard ATA host controller.
*
* LOCKING:
* Inherited from caller.
*/
void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
if (tf->ctl != ap->last_ctl) {
if (ioaddr->ctl_addr)
iowrite8(tf->ctl, ioaddr->ctl_addr);
ap->last_ctl = tf->ctl;
ata_wait_idle(ap);
}
if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
WARN_ON(!ioaddr->ctl_addr);
iowrite8(tf->hob_feature, ioaddr->feature_addr);
iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
tf->hob_feature,
tf->hob_nsect,
tf->hob_lbal,
tf->hob_lbam,
tf->hob_lbah);
}
if (is_addr) {
iowrite8(tf->feature, ioaddr->feature_addr);
iowrite8(tf->nsect, ioaddr->nsect_addr);
iowrite8(tf->lbal, ioaddr->lbal_addr);
iowrite8(tf->lbam, ioaddr->lbam_addr);
iowrite8(tf->lbah, ioaddr->lbah_addr);
VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
tf->feature,
tf->nsect,
tf->lbal,
tf->lbam,
tf->lbah);
}
if (tf->flags & ATA_TFLAG_DEVICE) {
iowrite8(tf->device, ioaddr->device_addr);
VPRINTK("device 0x%X\n", tf->device);
}
ata_wait_idle(ap);
}
/**
* ata_sff_tf_read - input device's ATA taskfile shadow registers
* @ap: Port from which input is read
* @tf: ATA taskfile register set for storing input
*
* Reads ATA taskfile registers for currently-selected device
* into @tf. Assumes the device has a fully SFF compliant task file
* layout and behaviour. If you device does not (eg has a different
* status method) then you will need to provide a replacement tf_read
*
* LOCKING:
* Inherited from caller.
*/
void ata_sff_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
tf->command = ata_sff_check_status(ap);
tf->feature = ioread8(ioaddr->error_addr);
tf->nsect = ioread8(ioaddr->nsect_addr);
tf->lbal = ioread8(ioaddr->lbal_addr);
tf->lbam = ioread8(ioaddr->lbam_addr);
tf->lbah = ioread8(ioaddr->lbah_addr);
tf->device = ioread8(ioaddr->device_addr);
if (tf->flags & ATA_TFLAG_LBA48) {
if (likely(ioaddr->ctl_addr)) {
iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
tf->hob_feature = ioread8(ioaddr->error_addr);
tf->hob_nsect = ioread8(ioaddr->nsect_addr);
tf->hob_lbal = ioread8(ioaddr->lbal_addr);
tf->hob_lbam = ioread8(ioaddr->lbam_addr);
tf->hob_lbah = ioread8(ioaddr->lbah_addr);
iowrite8(tf->ctl, ioaddr->ctl_addr);
ap->last_ctl = tf->ctl;
} else
WARN_ON(1);
}
}
/**
* ata_sff_exec_command - issue ATA command to host controller
* @ap: port to which command is being issued
* @tf: ATA taskfile register set
*
* Issues ATA command, with proper synchronization with interrupt
* handler / other threads.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
{
DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
iowrite8(tf->command, ap->ioaddr.command_addr);
ata_sff_pause(ap);
}
/**
* ata_tf_to_host - issue ATA taskfile to host controller
* @ap: port to which command is being issued
* @tf: ATA taskfile register set
*
* Issues ATA taskfile register set to ATA host controller,
* with proper synchronization with interrupt handler and
* other threads.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
static inline void ata_tf_to_host(struct ata_port *ap,
const struct ata_taskfile *tf)
{
ap->ops->sff_tf_load(ap, tf);
ap->ops->sff_exec_command(ap, tf);
}
/**
* ata_sff_data_xfer - Transfer data by PIO
* @dev: device to target
* @buf: data buffer
* @buflen: buffer length
* @rw: read/write
*
* Transfer data from/to the device data register by PIO.
*
* LOCKING:
* Inherited from caller.
*
* RETURNS:
* Bytes consumed.
*/
unsigned int ata_sff_data_xfer(struct ata_device *dev, unsigned char *buf,
unsigned int buflen, int rw)
{
struct ata_port *ap = dev->link->ap;
void __iomem *data_addr = ap->ioaddr.data_addr;
unsigned int words = buflen >> 1;
/* Transfer multiple of 2 bytes */
if (rw == READ)
ioread16_rep(data_addr, buf, words);
else
iowrite16_rep(data_addr, buf, words);
/* Transfer trailing 1 byte, if any. */
if (unlikely(buflen & 0x01)) {
__le16 align_buf[1] = { 0 };
unsigned char *trailing_buf = buf + buflen - 1;
if (rw == READ) {
align_buf[0] = cpu_to_le16(ioread16(data_addr));
memcpy(trailing_buf, align_buf, 1);
} else {
memcpy(align_buf, trailing_buf, 1);
iowrite16(le16_to_cpu(align_buf[0]), data_addr);
}
words++;
}
return words << 1;
}
/**
* ata_sff_data_xfer_noirq - Transfer data by PIO
* @dev: device to target
* @buf: data buffer
* @buflen: buffer length
* @rw: read/write
*
* Transfer data from/to the device data register by PIO. Do the
* transfer with interrupts disabled.
*
* LOCKING:
* Inherited from caller.
*
* RETURNS:
* Bytes consumed.
*/
unsigned int ata_sff_data_xfer_noirq(struct ata_device *dev, unsigned char *buf,
unsigned int buflen, int rw)
{
unsigned long flags;
unsigned int consumed;
local_irq_save(flags);
consumed = ata_sff_data_xfer(dev, buf, buflen, rw);
local_irq_restore(flags);
return consumed;
}
/**
* ata_pio_sector - Transfer a sector of data.
* @qc: Command on going
*
* Transfer qc->sect_size bytes of data from/to the ATA device.
*
* LOCKING:
* Inherited from caller.
*/
static void ata_pio_sector(struct ata_queued_cmd *qc)
{
int do_write = (qc->tf.flags & ATA_TFLAG_WRITE);
struct ata_port *ap = qc->ap;
struct page *page;
unsigned int offset;
unsigned char *buf;
if (qc->curbytes == qc->nbytes - qc->sect_size)
ap->hsm_task_state = HSM_ST_LAST;
page = sg_page(qc->cursg);
offset = qc->cursg->offset + qc->cursg_ofs;
/* get the current page and offset */
page = nth_page(page, (offset >> PAGE_SHIFT));
offset %= PAGE_SIZE;
DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
if (PageHighMem(page)) {
unsigned long flags;
/* FIXME: use a bounce buffer */
local_irq_save(flags);
buf = kmap_atomic(page, KM_IRQ0);
/* do the actual data transfer */
ap->ops->sff_data_xfer(qc->dev, buf + offset, qc->sect_size,
do_write);
kunmap_atomic(buf, KM_IRQ0);
local_irq_restore(flags);
} else {
buf = page_address(page);
ap->ops->sff_data_xfer(qc->dev, buf + offset, qc->sect_size,
do_write);
}
qc->curbytes += qc->sect_size;
qc->cursg_ofs += qc->sect_size;
if (qc->cursg_ofs == qc->cursg->length) {
qc->cursg = sg_next(qc->cursg);
qc->cursg_ofs = 0;
}
}
/**
* ata_pio_sectors - Transfer one or many sectors.
* @qc: Command on going
*
* Transfer one or many sectors of data from/to the
* ATA device for the DRQ request.
*
* LOCKING:
* Inherited from caller.
*/
static void ata_pio_sectors(struct ata_queued_cmd *qc)
{
if (is_multi_taskfile(&qc->tf)) {
/* READ/WRITE MULTIPLE */
unsigned int nsect;
WARN_ON(qc->dev->multi_count == 0);
nsect = min((qc->nbytes - qc->curbytes) / qc->sect_size,
qc->dev->multi_count);
while (nsect--)
ata_pio_sector(qc);
} else
ata_pio_sector(qc);
ata_sff_sync(qc->ap); /* flush */
}
/**
* atapi_send_cdb - Write CDB bytes to hardware
* @ap: Port to which ATAPI device is attached.
* @qc: Taskfile currently active
*
* When device has indicated its readiness to accept
* a CDB, this function is called. Send the CDB.
*
* LOCKING:
* caller.
*/
static void atapi_send_cdb(struct ata_port *ap, struct ata_queued_cmd *qc)
{
/* send SCSI cdb */
DPRINTK("send cdb\n");
WARN_ON(qc->dev->cdb_len < 12);
ap->ops->sff_data_xfer(qc->dev, qc->cdb, qc->dev->cdb_len, 1);
ata_sff_sync(ap);
/* FIXME: If the CDB is for DMA do we need to do the transition delay
or is bmdma_start guaranteed to do it ? */
switch (qc->tf.protocol) {
case ATAPI_PROT_PIO:
ap->hsm_task_state = HSM_ST;
break;
case ATAPI_PROT_NODATA:
ap->hsm_task_state = HSM_ST_LAST;
break;
case ATAPI_PROT_DMA:
ap->hsm_task_state = HSM_ST_LAST;
/* initiate bmdma */
ap->ops->bmdma_start(qc);
break;
}
}
/**
* __atapi_pio_bytes - Transfer data from/to the ATAPI device.
* @qc: Command on going
* @bytes: number of bytes
*
* Transfer Transfer data from/to the ATAPI device.
*
* LOCKING:
* Inherited from caller.
*
*/
static int __atapi_pio_bytes(struct ata_queued_cmd *qc, unsigned int bytes)
{
int rw = (qc->tf.flags & ATA_TFLAG_WRITE) ? WRITE : READ;
struct ata_port *ap = qc->ap;
struct ata_device *dev = qc->dev;
struct ata_eh_info *ehi = &dev->link->eh_info;
struct scatterlist *sg;
struct page *page;
unsigned char *buf;
unsigned int offset, count, consumed;
next_sg:
sg = qc->cursg;
if (unlikely(!sg)) {
ata_ehi_push_desc(ehi, "unexpected or too much trailing data "
"buf=%u cur=%u bytes=%u",
qc->nbytes, qc->curbytes, bytes);
return -1;
}
page = sg_page(sg);
offset = sg->offset + qc->cursg_ofs;
/* get the current page and offset */
page = nth_page(page, (offset >> PAGE_SHIFT));
offset %= PAGE_SIZE;
/* don't overrun current sg */
count = min(sg->length - qc->cursg_ofs, bytes);
/* don't cross page boundaries */
count = min(count, (unsigned int)PAGE_SIZE - offset);
DPRINTK("data %s\n", qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
if (PageHighMem(page)) {
unsigned long flags;
/* FIXME: use bounce buffer */
local_irq_save(flags);
buf = kmap_atomic(page, KM_IRQ0);
/* do the actual data transfer */
consumed = ap->ops->sff_data_xfer(dev, buf + offset, count, rw);
kunmap_atomic(buf, KM_IRQ0);
local_irq_restore(flags);
} else {
buf = page_address(page);
consumed = ap->ops->sff_data_xfer(dev, buf + offset, count, rw);
}
bytes -= min(bytes, consumed);
qc->curbytes += count;
qc->cursg_ofs += count;
if (qc->cursg_ofs == sg->length) {
qc->cursg = sg_next(qc->cursg);
qc->cursg_ofs = 0;
}
/* consumed can be larger than count only for the last transfer */
WARN_ON(qc->cursg && count != consumed);
if (bytes)
goto next_sg;
return 0;
}
/**
* atapi_pio_bytes - Transfer data from/to the ATAPI device.
* @qc: Command on going
*
* Transfer Transfer data from/to the ATAPI device.
*
* LOCKING:
* Inherited from caller.
*/
static void atapi_pio_bytes(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_device *dev = qc->dev;
struct ata_eh_info *ehi = &dev->link->eh_info;
unsigned int ireason, bc_lo, bc_hi, bytes;
int i_write, do_write = (qc->tf.flags & ATA_TFLAG_WRITE) ? 1 : 0;
/* Abuse qc->result_tf for temp storage of intermediate TF
* here to save some kernel stack usage.
* For normal completion, qc->result_tf is not relevant. For
* error, qc->result_tf is later overwritten by ata_qc_complete().
* So, the correctness of qc->result_tf is not affected.
*/
ap->ops->sff_tf_read(ap, &qc->result_tf);
ireason = qc->result_tf.nsect;
bc_lo = qc->result_tf.lbam;
bc_hi = qc->result_tf.lbah;
bytes = (bc_hi << 8) | bc_lo;
/* shall be cleared to zero, indicating xfer of data */
if (unlikely(ireason & (1 << 0)))
goto atapi_check;
/* make sure transfer direction matches expected */
i_write = ((ireason & (1 << 1)) == 0) ? 1 : 0;
if (unlikely(do_write != i_write))
goto atapi_check;
if (unlikely(!bytes))
goto atapi_check;
VPRINTK("ata%u: xfering %d bytes\n", ap->print_id, bytes);
if (unlikely(__atapi_pio_bytes(qc, bytes)))
goto err_out;
ata_sff_sync(ap); /* flush */
return;
atapi_check:
ata_ehi_push_desc(ehi, "ATAPI check failed (ireason=0x%x bytes=%u)",
ireason, bytes);
err_out:
qc->err_mask |= AC_ERR_HSM;
ap->hsm_task_state = HSM_ST_ERR;
}
/**
* ata_hsm_ok_in_wq - Check if the qc can be handled in the workqueue.
* @ap: the target ata_port
* @qc: qc on going
*
* RETURNS:
* 1 if ok in workqueue, 0 otherwise.
*/
static inline int ata_hsm_ok_in_wq(struct ata_port *ap, struct ata_queued_cmd *qc)
{
if (qc->tf.flags & ATA_TFLAG_POLLING)
return 1;
if (ap->hsm_task_state == HSM_ST_FIRST) {
if (qc->tf.protocol == ATA_PROT_PIO &&
(qc->tf.flags & ATA_TFLAG_WRITE))
return 1;
if (ata_is_atapi(qc->tf.protocol) &&
!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
return 1;
}
return 0;
}
/**
* ata_hsm_qc_complete - finish a qc running on standard HSM
* @qc: Command to complete
* @in_wq: 1 if called from workqueue, 0 otherwise
*
* Finish @qc which is running on standard HSM.
*
* LOCKING:
* If @in_wq is zero, spin_lock_irqsave(host lock).
* Otherwise, none on entry and grabs host lock.
*/
static void ata_hsm_qc_complete(struct ata_queued_cmd *qc, int in_wq)
{
struct ata_port *ap = qc->ap;
unsigned long flags;
if (ap->ops->error_handler) {
if (in_wq) {
spin_lock_irqsave(ap->lock, flags);
/* EH might have kicked in while host lock is
* released.
*/
qc = ata_qc_from_tag(ap, qc->tag);
if (qc) {
if (likely(!(qc->err_mask & AC_ERR_HSM))) {
ap->ops->sff_irq_on(ap);
ata_qc_complete(qc);
} else
ata_port_freeze(ap);
}
spin_unlock_irqrestore(ap->lock, flags);
} else {
if (likely(!(qc->err_mask & AC_ERR_HSM)))
ata_qc_complete(qc);
else
ata_port_freeze(ap);
}
} else {
if (in_wq) {
spin_lock_irqsave(ap->lock, flags);
ap->ops->sff_irq_on(ap);
ata_qc_complete(qc);
spin_unlock_irqrestore(ap->lock, flags);
} else
ata_qc_complete(qc);
}
}
/**
* ata_sff_hsm_move - move the HSM to the next state.
* @ap: the target ata_port
* @qc: qc on going
* @status: current device status
* @in_wq: 1 if called from workqueue, 0 otherwise
*
* RETURNS:
* 1 when poll next status needed, 0 otherwise.
*/
int ata_sff_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
u8 status, int in_wq)
{
struct ata_eh_info *ehi = &ap->link.eh_info;
unsigned long flags = 0;
int poll_next;
WARN_ON((qc->flags & ATA_QCFLAG_ACTIVE) == 0);
/* Make sure ata_sff_qc_issue() does not throw things
* like DMA polling into the workqueue. Notice that
* in_wq is not equivalent to (qc->tf.flags & ATA_TFLAG_POLLING).
*/
WARN_ON(in_wq != ata_hsm_ok_in_wq(ap, qc));
fsm_start:
DPRINTK("ata%u: protocol %d task_state %d (dev_stat 0x%X)\n",
ap->print_id, qc->tf.protocol, ap->hsm_task_state, status);
switch (ap->hsm_task_state) {
case HSM_ST_FIRST:
/* Send first data block or PACKET CDB */
/* If polling, we will stay in the work queue after
* sending the data. Otherwise, interrupt handler
* takes over after sending the data.
*/
poll_next = (qc->tf.flags & ATA_TFLAG_POLLING);
/* check device status */
if (unlikely((status & ATA_DRQ) == 0)) {
/* handle BSY=0, DRQ=0 as error */
if (likely(status & (ATA_ERR | ATA_DF)))
/* device stops HSM for abort/error */
qc->err_mask |= AC_ERR_DEV;
else {
/* HSM violation. Let EH handle this */
ata_ehi_push_desc(ehi,
"ST_FIRST: !(DRQ|ERR|DF)");
qc->err_mask |= AC_ERR_HSM;
}
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
/* Device should not ask for data transfer (DRQ=1)
* when it finds something wrong.
* We ignore DRQ here and stop the HSM by
* changing hsm_task_state to HSM_ST_ERR and
* let the EH abort the command or reset the device.
*/
if (unlikely(status & (ATA_ERR | ATA_DF))) {
/* Some ATAPI tape drives forget to clear the ERR bit
* when doing the next command (mostly request sense).
* We ignore ERR here to workaround and proceed sending
* the CDB.
*/
if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
ata_ehi_push_desc(ehi, "ST_FIRST: "
"DRQ=1 with device error, "
"dev_stat 0x%X", status);
qc->err_mask |= AC_ERR_HSM;
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
}
/* Send the CDB (atapi) or the first data block (ata pio out).
* During the state transition, interrupt handler shouldn't
* be invoked before the data transfer is complete and
* hsm_task_state is changed. Hence, the following locking.
*/
if (in_wq)
spin_lock_irqsave(ap->lock, flags);
if (qc->tf.protocol == ATA_PROT_PIO) {
/* PIO data out protocol.
* send first data block.
*/
/* ata_pio_sectors() might change the state
* to HSM_ST_LAST. so, the state is changed here
* before ata_pio_sectors().
*/
ap->hsm_task_state = HSM_ST;
ata_pio_sectors(qc);
} else
/* send CDB */
atapi_send_cdb(ap, qc);
if (in_wq)
spin_unlock_irqrestore(ap->lock, flags);
/* if polling, ata_pio_task() handles the rest.
* otherwise, interrupt handler takes over from here.
*/
break;
case HSM_ST:
/* complete command or read/write the data register */
if (qc->tf.protocol == ATAPI_PROT_PIO) {
/* ATAPI PIO protocol */
if ((status & ATA_DRQ) == 0) {
/* No more data to transfer or device error.
* Device error will be tagged in HSM_ST_LAST.
*/
ap->hsm_task_state = HSM_ST_LAST;
goto fsm_start;
}
/* Device should not ask for data transfer (DRQ=1)
* when it finds something wrong.
* We ignore DRQ here and stop the HSM by
* changing hsm_task_state to HSM_ST_ERR and
* let the EH abort the command or reset the device.
*/
if (unlikely(status & (ATA_ERR | ATA_DF))) {
ata_ehi_push_desc(ehi, "ST-ATAPI: "
"DRQ=1 with device error, "
"dev_stat 0x%X", status);
qc->err_mask |= AC_ERR_HSM;
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
atapi_pio_bytes(qc);
if (unlikely(ap->hsm_task_state == HSM_ST_ERR))
/* bad ireason reported by device */
goto fsm_start;
} else {
/* ATA PIO protocol */
if (unlikely((status & ATA_DRQ) == 0)) {
/* handle BSY=0, DRQ=0 as error */
if (likely(status & (ATA_ERR | ATA_DF))) {
/* device stops HSM for abort/error */
qc->err_mask |= AC_ERR_DEV;
/* If diagnostic failed and this is
* IDENTIFY, it's likely a phantom
* device. Mark hint.
*/
if (qc->dev->horkage &
ATA_HORKAGE_DIAGNOSTIC)
qc->err_mask |=
AC_ERR_NODEV_HINT;
} else {
/* HSM violation. Let EH handle this.
* Phantom devices also trigger this
* condition. Mark hint.
*/
ata_ehi_push_desc(ehi, "ST-ATA: "
"DRQ=1 with device error, "
"dev_stat 0x%X", status);
qc->err_mask |= AC_ERR_HSM |
AC_ERR_NODEV_HINT;
}
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
/* For PIO reads, some devices may ask for
* data transfer (DRQ=1) alone with ERR=1.
* We respect DRQ here and transfer one
* block of junk data before changing the
* hsm_task_state to HSM_ST_ERR.
*
* For PIO writes, ERR=1 DRQ=1 doesn't make
* sense since the data block has been
* transferred to the device.
*/
if (unlikely(status & (ATA_ERR | ATA_DF))) {
/* data might be corrputed */
qc->err_mask |= AC_ERR_DEV;
if (!(qc->tf.flags & ATA_TFLAG_WRITE)) {
ata_pio_sectors(qc);
status = ata_wait_idle(ap);
}
if (status & (ATA_BUSY | ATA_DRQ)) {
ata_ehi_push_desc(ehi, "ST-ATA: "
"BUSY|DRQ persists on ERR|DF, "
"dev_stat 0x%X", status);
qc->err_mask |= AC_ERR_HSM;
}
/* ata_pio_sectors() might change the
* state to HSM_ST_LAST. so, the state
* is changed after ata_pio_sectors().
*/
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
ata_pio_sectors(qc);
if (ap->hsm_task_state == HSM_ST_LAST &&
(!(qc->tf.flags & ATA_TFLAG_WRITE))) {
/* all data read */
status = ata_wait_idle(ap);
goto fsm_start;
}
}
poll_next = 1;
break;
case HSM_ST_LAST:
if (unlikely(!ata_ok(status))) {
qc->err_mask |= __ac_err_mask(status);
ap->hsm_task_state = HSM_ST_ERR;
goto fsm_start;
}
/* no more data to transfer */
DPRINTK("ata%u: dev %u command complete, drv_stat 0x%x\n",
ap->print_id, qc->dev->devno, status);
WARN_ON(qc->err_mask & (AC_ERR_DEV | AC_ERR_HSM));
ap->hsm_task_state = HSM_ST_IDLE;
/* complete taskfile transaction */
ata_hsm_qc_complete(qc, in_wq);
poll_next = 0;
break;
case HSM_ST_ERR:
ap->hsm_task_state = HSM_ST_IDLE;
/* complete taskfile transaction */
ata_hsm_qc_complete(qc, in_wq);
poll_next = 0;
break;
default:
poll_next = 0;
BUG();
}
return poll_next;
}
void ata_pio_task(struct work_struct *work)
{
struct ata_port *ap =
container_of(work, struct ata_port, port_task.work);
struct ata_queued_cmd *qc = ap->port_task_data;
u8 status;
int poll_next;
fsm_start:
WARN_ON(ap->hsm_task_state == HSM_ST_IDLE);
/*
* This is purely heuristic. This is a fast path.
* Sometimes when we enter, BSY will be cleared in
* a chk-status or two. If not, the drive is probably seeking
* or something. Snooze for a couple msecs, then
* chk-status again. If still busy, queue delayed work.
*/
status = ata_sff_busy_wait(ap, ATA_BUSY, 5);
if (status & ATA_BUSY) {
msleep(2);
status = ata_sff_busy_wait(ap, ATA_BUSY, 10);
if (status & ATA_BUSY) {
ata_pio_queue_task(ap, qc, ATA_SHORT_PAUSE);
return;
}
}
/* move the HSM */
poll_next = ata_sff_hsm_move(ap, qc, status, 1);
/* another command or interrupt handler
* may be running at this point.
*/
if (poll_next)
goto fsm_start;
}
/**
* ata_sff_qc_issue - issue taskfile to device in proto-dependent manner
* @qc: command to issue to device
*
* Using various libata functions and hooks, this function
* starts an ATA command. ATA commands are grouped into
* classes called "protocols", and issuing each type of protocol
* is slightly different.
*
* May be used as the qc_issue() entry in ata_port_operations.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
* RETURNS:
* Zero on success, AC_ERR_* mask on failure
*/
unsigned int ata_sff_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
/* Use polling pio if the LLD doesn't handle
* interrupt driven pio and atapi CDB interrupt.
*/
if (ap->flags & ATA_FLAG_PIO_POLLING) {
switch (qc->tf.protocol) {
case ATA_PROT_PIO:
case ATA_PROT_NODATA:
case ATAPI_PROT_PIO:
case ATAPI_PROT_NODATA:
qc->tf.flags |= ATA_TFLAG_POLLING;
break;
case ATAPI_PROT_DMA:
if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
/* see ata_dma_blacklisted() */
BUG();
break;
default:
break;
}
}
/* select the device */
ata_dev_select(ap, qc->dev->devno, 1, 0);
/* start the command */
switch (qc->tf.protocol) {
case ATA_PROT_NODATA:
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_qc_set_polling(qc);
ata_tf_to_host(ap, &qc->tf);
ap->hsm_task_state = HSM_ST_LAST;
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_pio_queue_task(ap, qc, 0);
break;
case ATA_PROT_DMA:
WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
ap->ops->sff_tf_load(ap, &qc->tf); /* load tf registers */
ap->ops->bmdma_setup(qc); /* set up bmdma */
ap->ops->bmdma_start(qc); /* initiate bmdma */
ap->hsm_task_state = HSM_ST_LAST;
break;
case ATA_PROT_PIO:
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_qc_set_polling(qc);
ata_tf_to_host(ap, &qc->tf);
if (qc->tf.flags & ATA_TFLAG_WRITE) {
/* PIO data out protocol */
ap->hsm_task_state = HSM_ST_FIRST;
ata_pio_queue_task(ap, qc, 0);
/* always send first data block using
* the ata_pio_task() codepath.
*/
} else {
/* PIO data in protocol */
ap->hsm_task_state = HSM_ST;
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_pio_queue_task(ap, qc, 0);
/* if polling, ata_pio_task() handles the rest.
* otherwise, interrupt handler takes over from here.
*/
}
break;
case ATAPI_PROT_PIO:
case ATAPI_PROT_NODATA:
if (qc->tf.flags & ATA_TFLAG_POLLING)
ata_qc_set_polling(qc);
ata_tf_to_host(ap, &qc->tf);
ap->hsm_task_state = HSM_ST_FIRST;
/* send cdb by polling if no cdb interrupt */
if ((!(qc->dev->flags & ATA_DFLAG_CDB_INTR)) ||
(qc->tf.flags & ATA_TFLAG_POLLING))
ata_pio_queue_task(ap, qc, 0);
break;
case ATAPI_PROT_DMA:
WARN_ON(qc->tf.flags & ATA_TFLAG_POLLING);
ap->ops->sff_tf_load(ap, &qc->tf); /* load tf registers */
ap->ops->bmdma_setup(qc); /* set up bmdma */
ap->hsm_task_state = HSM_ST_FIRST;
/* send cdb by polling if no cdb interrupt */
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
ata_pio_queue_task(ap, qc, 0);
break;
default:
WARN_ON(1);
return AC_ERR_SYSTEM;
}
return 0;
}
/**
* ata_sff_qc_fill_rtf - fill result TF using ->sff_tf_read
* @qc: qc to fill result TF for
*
* @qc is finished and result TF needs to be filled. Fill it
* using ->sff_tf_read.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
* RETURNS:
* true indicating that result TF is successfully filled.
*/
bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc)
{
qc->ap->ops->sff_tf_read(qc->ap, &qc->result_tf);
return true;
}
/**
* ata_sff_host_intr - Handle host interrupt for given (port, task)
* @ap: Port on which interrupt arrived (possibly...)
* @qc: Taskfile currently active in engine
*
* Handle host interrupt for given queued command. Currently,
* only DMA interrupts are handled. All other commands are
* handled via polling with interrupts disabled (nIEN bit).
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
* RETURNS:
* One if interrupt was handled, zero if not (shared irq).
*/
inline unsigned int ata_sff_host_intr(struct ata_port *ap,
struct ata_queued_cmd *qc)
{
struct ata_eh_info *ehi = &ap->link.eh_info;
u8 status, host_stat = 0;
VPRINTK("ata%u: protocol %d task_state %d\n",
ap->print_id, qc->tf.protocol, ap->hsm_task_state);
/* Check whether we are expecting interrupt in this state */
switch (ap->hsm_task_state) {
case HSM_ST_FIRST:
/* Some pre-ATAPI-4 devices assert INTRQ
* at this state when ready to receive CDB.
*/
/* Check the ATA_DFLAG_CDB_INTR flag is enough here.
* The flag was turned on only for atapi devices. No
* need to check ata_is_atapi(qc->tf.protocol) again.
*/
if (!(qc->dev->flags & ATA_DFLAG_CDB_INTR))
goto idle_irq;
break;
case HSM_ST_LAST:
if (qc->tf.protocol == ATA_PROT_DMA ||
qc->tf.protocol == ATAPI_PROT_DMA) {
/* check status of DMA engine */
host_stat = ap->ops->bmdma_status(ap);
VPRINTK("ata%u: host_stat 0x%X\n",
ap->print_id, host_stat);
/* if it's not our irq... */
if (!(host_stat & ATA_DMA_INTR))
goto idle_irq;
/* before we do anything else, clear DMA-Start bit */
ap->ops->bmdma_stop(qc);
if (unlikely(host_stat & ATA_DMA_ERR)) {
/* error when transfering data to/from memory */
qc->err_mask |= AC_ERR_HOST_BUS;
ap->hsm_task_state = HSM_ST_ERR;
}
}
break;
case HSM_ST:
break;
default:
goto idle_irq;
}
/* check main status, clearing INTRQ if needed */
status = ata_sff_irq_status(ap);
if (status & ATA_BUSY)
goto idle_irq;
/* ack bmdma irq events */
ap->ops->sff_irq_clear(ap);
ata_sff_hsm_move(ap, qc, status, 0);
if (unlikely(qc->err_mask) && (qc->tf.protocol == ATA_PROT_DMA ||
qc->tf.protocol == ATAPI_PROT_DMA))
ata_ehi_push_desc(ehi, "BMDMA stat 0x%x", host_stat);
return 1; /* irq handled */
idle_irq:
ap->stats.idle_irq++;
#ifdef ATA_IRQ_TRAP
if ((ap->stats.idle_irq % 1000) == 0) {
ap->ops->sff_check_status(ap);
ap->ops->sff_irq_clear(ap);
ata_port_printk(ap, KERN_WARNING, "irq trap\n");
return 1;
}
#endif
return 0; /* irq not handled */
}
/**
* ata_sff_interrupt - Default ATA host interrupt handler
* @irq: irq line (unused)
* @dev_instance: pointer to our ata_host information structure
*
* Default interrupt handler for PCI IDE devices. Calls
* ata_sff_host_intr() for each port that is not disabled.
*
* LOCKING:
* Obtains host lock during operation.
*
* RETURNS:
* IRQ_NONE or IRQ_HANDLED.
*/
irqreturn_t ata_sff_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
unsigned int i;
unsigned int handled = 0;
unsigned long flags;
/* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */
spin_lock_irqsave(&host->lock, flags);
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap;
ap = host->ports[i];
if (ap &&
!(ap->flags & ATA_FLAG_DISABLED)) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) &&
(qc->flags & ATA_QCFLAG_ACTIVE))
handled |= ata_sff_host_intr(ap, qc);
}
}
spin_unlock_irqrestore(&host->lock, flags);
return IRQ_RETVAL(handled);
}
/**
* ata_sff_freeze - Freeze SFF controller port
* @ap: port to freeze
*
* Freeze BMDMA controller port.
*
* LOCKING:
* Inherited from caller.
*/
void ata_sff_freeze(struct ata_port *ap)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
ap->ctl |= ATA_NIEN;
ap->last_ctl = ap->ctl;
if (ioaddr->ctl_addr)
iowrite8(ap->ctl, ioaddr->ctl_addr);
/* Under certain circumstances, some controllers raise IRQ on
* ATA_NIEN manipulation. Also, many controllers fail to mask
* previously pending IRQ on ATA_NIEN assertion. Clear it.
*/
ap->ops->sff_check_status(ap);
ap->ops->sff_irq_clear(ap);
}
/**
* ata_sff_thaw - Thaw SFF controller port
* @ap: port to thaw
*
* Thaw SFF controller port.
*
* LOCKING:
* Inherited from caller.
*/
void ata_sff_thaw(struct ata_port *ap)
{
/* clear & re-enable interrupts */
ap->ops->sff_check_status(ap);
ap->ops->sff_irq_clear(ap);
ap->ops->sff_irq_on(ap);
}
/**
* ata_sff_prereset - prepare SFF link for reset
* @link: SFF link to be reset
* @deadline: deadline jiffies for the operation
*
* SFF link @link is about to be reset. Initialize it. It first
* calls ata_std_prereset() and wait for !BSY if the port is
* being softreset.
*
* LOCKING:
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_sff_prereset(struct ata_link *link, unsigned long deadline)
{
struct ata_eh_context *ehc = &link->eh_context;
int rc;
rc = ata_std_prereset(link, deadline);
if (rc)
return rc;
/* if we're about to do hardreset, nothing more to do */
if (ehc->i.action & ATA_EH_HARDRESET)
return 0;
/* wait for !BSY if we don't know that no device is attached */
if (!ata_link_offline(link)) {
rc = ata_sff_wait_ready(link, deadline);
if (rc && rc != -ENODEV) {
ata_link_printk(link, KERN_WARNING, "device not ready "
"(errno=%d), forcing hardreset\n", rc);
ehc->i.action |= ATA_EH_HARDRESET;
}
}
return 0;
}
/**
* ata_devchk - PATA device presence detection
* @ap: ATA channel to examine
* @device: Device to examine (starting at zero)
*
* This technique was originally described in
* Hale Landis's ATADRVR (www.ata-atapi.com), and
* later found its way into the ATA/ATAPI spec.
*
* Write a pattern to the ATA shadow registers,
* and if a device is present, it will respond by
* correctly storing and echoing back the
* ATA shadow register contents.
*
* LOCKING:
* caller.
*/
static unsigned int ata_devchk(struct ata_port *ap, unsigned int device)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
u8 nsect, lbal;
ap->ops->sff_dev_select(ap, device);
iowrite8(0x55, ioaddr->nsect_addr);
iowrite8(0xaa, ioaddr->lbal_addr);
iowrite8(0xaa, ioaddr->nsect_addr);
iowrite8(0x55, ioaddr->lbal_addr);
iowrite8(0x55, ioaddr->nsect_addr);
iowrite8(0xaa, ioaddr->lbal_addr);
nsect = ioread8(ioaddr->nsect_addr);
lbal = ioread8(ioaddr->lbal_addr);
if ((nsect == 0x55) && (lbal == 0xaa))
return 1; /* we found a device */
return 0; /* nothing found */
}
/**
* ata_sff_dev_classify - Parse returned ATA device signature
* @dev: ATA device to classify (starting at zero)
* @present: device seems present
* @r_err: Value of error register on completion
*
* After an event -- SRST, E.D.D., or SATA COMRESET -- occurs,
* an ATA/ATAPI-defined set of values is placed in the ATA
* shadow registers, indicating the results of device detection
* and diagnostics.
*
* Select the ATA device, and read the values from the ATA shadow
* registers. Then parse according to the Error register value,
* and the spec-defined values examined by ata_dev_classify().
*
* LOCKING:
* caller.
*
* RETURNS:
* Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE.
*/
unsigned int ata_sff_dev_classify(struct ata_device *dev, int present,
u8 *r_err)
{
struct ata_port *ap = dev->link->ap;
struct ata_taskfile tf;
unsigned int class;
u8 err;
ap->ops->sff_dev_select(ap, dev->devno);
memset(&tf, 0, sizeof(tf));
ap->ops->sff_tf_read(ap, &tf);
err = tf.feature;
if (r_err)
*r_err = err;
/* see if device passed diags: continue and warn later */
if (err == 0)
/* diagnostic fail : do nothing _YET_ */
dev->horkage |= ATA_HORKAGE_DIAGNOSTIC;
else if (err == 1)
/* do nothing */ ;
else if ((dev->devno == 0) && (err == 0x81))
/* do nothing */ ;
else
return ATA_DEV_NONE;
/* determine if device is ATA or ATAPI */
class = ata_dev_classify(&tf);
if (class == ATA_DEV_UNKNOWN) {
/* If the device failed diagnostic, it's likely to
* have reported incorrect device signature too.
* Assume ATA device if the device seems present but
* device signature is invalid with diagnostic
* failure.
*/
if (present && (dev->horkage & ATA_HORKAGE_DIAGNOSTIC))
class = ATA_DEV_ATA;
else
class = ATA_DEV_NONE;
} else if ((class == ATA_DEV_ATA) &&
(ap->ops->sff_check_status(ap) == 0))
class = ATA_DEV_NONE;
return class;
}
/**
* ata_sff_wait_after_reset - wait for devices to become ready after reset
* @link: SFF link which is just reset
* @devmask: mask of present devices
* @deadline: deadline jiffies for the operation
*
* Wait devices attached to SFF @link to become ready after
* reset. It contains preceding 150ms wait to avoid accessing TF
* status register too early.
*
* LOCKING:
* Kernel thread context (may sleep).
*
* RETURNS:
* 0 on success, -ENODEV if some or all of devices in @devmask
* don't seem to exist. -errno on other errors.
*/
int ata_sff_wait_after_reset(struct ata_link *link, unsigned int devmask,
unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int dev0 = devmask & (1 << 0);
unsigned int dev1 = devmask & (1 << 1);
int rc, ret = 0;
msleep(ATA_WAIT_AFTER_RESET);
/* always check readiness of the master device */
rc = ata_sff_wait_ready(link, deadline);
/* -ENODEV means the odd clown forgot the D7 pulldown resistor
* and TF status is 0xff, bail out on it too.
*/
if (rc)
return rc;
/* if device 1 was found in ata_devchk, wait for register
* access briefly, then wait for BSY to clear.
*/
if (dev1) {
int i;
ap->ops->sff_dev_select(ap, 1);
/* Wait for register access. Some ATAPI devices fail
* to set nsect/lbal after reset, so don't waste too
* much time on it. We're gonna wait for !BSY anyway.
*/
for (i = 0; i < 2; i++) {
u8 nsect, lbal;
nsect = ioread8(ioaddr->nsect_addr);
lbal = ioread8(ioaddr->lbal_addr);
if ((nsect == 1) && (lbal == 1))
break;
msleep(50); /* give drive a breather */
}
rc = ata_sff_wait_ready(link, deadline);
if (rc) {
if (rc != -ENODEV)
return rc;
ret = rc;
}
}
/* is all this really necessary? */
ap->ops->sff_dev_select(ap, 0);
if (dev1)
ap->ops->sff_dev_select(ap, 1);
if (dev0)
ap->ops->sff_dev_select(ap, 0);
return ret;
}
static int ata_bus_softreset(struct ata_port *ap, unsigned int devmask,
unsigned long deadline)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
/* software reset. causes dev0 to be selected */
iowrite8(ap->ctl, ioaddr->ctl_addr);
udelay(20); /* FIXME: flush */
iowrite8(ap->ctl | ATA_SRST, ioaddr->ctl_addr);
udelay(20); /* FIXME: flush */
iowrite8(ap->ctl, ioaddr->ctl_addr);
/* wait the port to become ready */
return ata_sff_wait_after_reset(&ap->link, devmask, deadline);
}
/**
* ata_sff_softreset - reset host port via ATA SRST
* @link: ATA link to reset
* @classes: resulting classes of attached devices
* @deadline: deadline jiffies for the operation
*
* Reset host port using ATA SRST.
*
* LOCKING:
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_sff_softreset(struct ata_link *link, unsigned int *classes,
unsigned long deadline)
{
struct ata_port *ap = link->ap;
unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
unsigned int devmask = 0;
int rc;
u8 err;
DPRINTK("ENTER\n");
/* determine if device 0/1 are present */
if (ata_devchk(ap, 0))
devmask |= (1 << 0);
if (slave_possible && ata_devchk(ap, 1))
devmask |= (1 << 1);
/* select device 0 again */
ap->ops->sff_dev_select(ap, 0);
/* issue bus reset */
DPRINTK("about to softreset, devmask=%x\n", devmask);
rc = ata_bus_softreset(ap, devmask, deadline);
/* if link is occupied, -ENODEV too is an error */
if (rc && (rc != -ENODEV || sata_scr_valid(link))) {
ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc);
return rc;
}
/* determine by signature whether we have ATA or ATAPI devices */
classes[0] = ata_sff_dev_classify(&link->device[0],
devmask & (1 << 0), &err);
if (slave_possible && err != 0x81)
classes[1] = ata_sff_dev_classify(&link->device[1],
devmask & (1 << 1), &err);
DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
return 0;
}
/**
* sata_sff_hardreset - reset host port via SATA phy reset
* @link: link to reset
* @class: resulting class of attached device
* @deadline: deadline jiffies for the operation
*
* SATA phy-reset host port using DET bits of SControl register,
* wait for !BSY and classify the attached device.
*
* LOCKING:
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int sata_sff_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
struct ata_eh_context *ehc = &link->eh_context;
const unsigned long *timing = sata_ehc_deb_timing(ehc);
bool online;
int rc;
rc = sata_link_hardreset(link, timing, deadline, &online,
ata_sff_check_ready);
if (online)
*class = ata_sff_dev_classify(link->device, 1, NULL);
DPRINTK("EXIT, class=%u\n", *class);
return rc;
}
/**
* ata_sff_postreset - SFF postreset callback
* @link: the target SFF ata_link
* @classes: classes of attached devices
*
* This function is invoked after a successful reset. It first
* calls ata_std_postreset() and performs SFF specific postreset
* processing.
*
* LOCKING:
* Kernel thread context (may sleep)
*/
void ata_sff_postreset(struct ata_link *link, unsigned int *classes)
{
struct ata_port *ap = link->ap;
ata_std_postreset(link, classes);
/* is double-select really necessary? */
if (classes[0] != ATA_DEV_NONE)
ap->ops->sff_dev_select(ap, 1);
if (classes[1] != ATA_DEV_NONE)
ap->ops->sff_dev_select(ap, 0);
/* bail out if no device is present */
if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
DPRINTK("EXIT, no device\n");
return;
}
/* set up device control */
if (ap->ioaddr.ctl_addr)
iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
}
/**
* ata_sff_error_handler - Stock error handler for BMDMA controller
* @ap: port to handle error for
*
* Stock error handler for SFF controller. It can handle both
* PATA and SATA controllers. Many controllers should be able to
* use this EH as-is or with some added handling before and
* after.
*
* LOCKING:
* Kernel thread context (may sleep)
*/
void ata_sff_error_handler(struct ata_port *ap)
{
ata_reset_fn_t softreset = ap->ops->softreset;
ata_reset_fn_t hardreset = ap->ops->hardreset;
struct ata_queued_cmd *qc;
unsigned long flags;
int thaw = 0;
qc = __ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && !(qc->flags & ATA_QCFLAG_FAILED))
qc = NULL;
/* reset PIO HSM and stop DMA engine */
spin_lock_irqsave(ap->lock, flags);
ap->hsm_task_state = HSM_ST_IDLE;
if (ap->ioaddr.bmdma_addr &&
qc && (qc->tf.protocol == ATA_PROT_DMA ||
qc->tf.protocol == ATAPI_PROT_DMA)) {
u8 host_stat;
host_stat = ap->ops->bmdma_status(ap);
/* BMDMA controllers indicate host bus error by
* setting DMA_ERR bit and timing out. As it wasn't
* really a timeout event, adjust error mask and
* cancel frozen state.
*/
if (qc->err_mask == AC_ERR_TIMEOUT && (host_stat & ATA_DMA_ERR)) {
qc->err_mask = AC_ERR_HOST_BUS;
thaw = 1;
}
ap->ops->bmdma_stop(qc);
}
ata_sff_sync(ap); /* FIXME: We don't need this */
ap->ops->sff_check_status(ap);
ap->ops->sff_irq_clear(ap);
spin_unlock_irqrestore(ap->lock, flags);
if (thaw)
ata_eh_thaw_port(ap);
/* PIO and DMA engines have been stopped, perform recovery */
/* Ignore ata_sff_softreset if ctl isn't accessible and
* built-in hardresets if SCR access isn't available.
*/
if (softreset == ata_sff_softreset && !ap->ioaddr.ctl_addr)
softreset = NULL;
if (ata_is_builtin_hardreset(hardreset) && !sata_scr_valid(&ap->link))
hardreset = NULL;
ata_do_eh(ap, ap->ops->prereset, softreset, hardreset,
ap->ops->postreset);
}
/**
* ata_sff_post_internal_cmd - Stock post_internal_cmd for SFF controller
* @qc: internal command to clean up
*
* LOCKING:
* Kernel thread context (may sleep)
*/
void ata_sff_post_internal_cmd(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
unsigned long flags;
spin_lock_irqsave(ap->lock, flags);
ap->hsm_task_state = HSM_ST_IDLE;
if (ap->ioaddr.bmdma_addr)
ata_bmdma_stop(qc);
spin_unlock_irqrestore(ap->lock, flags);
}
/**
* ata_sff_port_start - Set port up for dma.
* @ap: Port to initialize
*
* Called just after data structures for each port are
* initialized. Allocates space for PRD table if the device
* is DMA capable SFF.
*
* May be used as the port_start() entry in ata_port_operations.
*
* LOCKING:
* Inherited from caller.
*/
int ata_sff_port_start(struct ata_port *ap)
{
if (ap->ioaddr.bmdma_addr)
return ata_port_start(ap);
return 0;
}
/**
* ata_sff_std_ports - initialize ioaddr with standard port offsets.
* @ioaddr: IO address structure to be initialized
*
* Utility function which initializes data_addr, error_addr,
* feature_addr, nsect_addr, lbal_addr, lbam_addr, lbah_addr,
* device_addr, status_addr, and command_addr to standard offsets
* relative to cmd_addr.
*
* Does not set ctl_addr, altstatus_addr, bmdma_addr, or scr_addr.
*/
void ata_sff_std_ports(struct ata_ioports *ioaddr)
{
ioaddr->data_addr = ioaddr->cmd_addr + ATA_REG_DATA;
ioaddr->error_addr = ioaddr->cmd_addr + ATA_REG_ERR;
ioaddr->feature_addr = ioaddr->cmd_addr + ATA_REG_FEATURE;
ioaddr->nsect_addr = ioaddr->cmd_addr + ATA_REG_NSECT;
ioaddr->lbal_addr = ioaddr->cmd_addr + ATA_REG_LBAL;
ioaddr->lbam_addr = ioaddr->cmd_addr + ATA_REG_LBAM;
ioaddr->lbah_addr = ioaddr->cmd_addr + ATA_REG_LBAH;
ioaddr->device_addr = ioaddr->cmd_addr + ATA_REG_DEVICE;
ioaddr->status_addr = ioaddr->cmd_addr + ATA_REG_STATUS;
ioaddr->command_addr = ioaddr->cmd_addr + ATA_REG_CMD;
}
unsigned long ata_bmdma_mode_filter(struct ata_device *adev,
unsigned long xfer_mask)
{
/* Filter out DMA modes if the device has been configured by
the BIOS as PIO only */
if (adev->link->ap->ioaddr.bmdma_addr == NULL)
xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
return xfer_mask;
}
/**
* ata_bmdma_setup - Set up PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_bmdma_setup(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
u8 dmactl;
/* load PRD table addr. */
mb(); /* make sure PRD table writes are visible to controller */
iowrite32(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
/* specify data direction, triple-check start bit is clear */
dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
if (!rw)
dmactl |= ATA_DMA_WR;
iowrite8(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
/* issue r/w command */
ap->ops->sff_exec_command(ap, &qc->tf);
}
/**
* ata_bmdma_start - Start a PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
u8 dmactl;
/* start host DMA transaction */
dmactl = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
iowrite8(dmactl | ATA_DMA_START, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
/* Strictly, one may wish to issue an ioread8() here, to
* flush the mmio write. However, control also passes
* to the hardware at this point, and it will interrupt
* us when we are to resume control. So, in effect,
* we don't care when the mmio write flushes.
* Further, a read of the DMA status register _immediately_
* following the write may not be what certain flaky hardware
* is expected, so I think it is best to not add a readb()
* without first all the MMIO ATA cards/mobos.
* Or maybe I'm just being paranoid.
*
* FIXME: The posting of this write means I/O starts are
* unneccessarily delayed for MMIO
*/
}
/**
* ata_bmdma_stop - Stop PCI IDE BMDMA transfer
* @qc: Command we are ending DMA for
*
* Clears the ATA_DMA_START flag in the dma control register
*
* May be used as the bmdma_stop() entry in ata_port_operations.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
void ata_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
void __iomem *mmio = ap->ioaddr.bmdma_addr;
/* clear start/stop bit */
iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ATA_DMA_START,
mmio + ATA_DMA_CMD);
/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
ata_sff_dma_pause(ap);
}
/**
* ata_bmdma_status - Read PCI IDE BMDMA status
* @ap: Port associated with this ATA transaction.
*
* Read and return BMDMA status register.
*
* May be used as the bmdma_status() entry in ata_port_operations.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*/
u8 ata_bmdma_status(struct ata_port *ap)
{
return ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
}
/**
* ata_bus_reset - reset host port and associated ATA channel
* @ap: port to reset
*
* This is typically the first time we actually start issuing
* commands to the ATA channel. We wait for BSY to clear, then
* issue EXECUTE DEVICE DIAGNOSTIC command, polling for its
* result. Determine what devices, if any, are on the channel
* by looking at the device 0/1 error register. Look at the signature
* stored in each device's taskfile registers, to determine if
* the device is ATA or ATAPI.
*
* LOCKING:
* PCI/etc. bus probe sem.
* Obtains host lock.
*
* SIDE EFFECTS:
* Sets ATA_FLAG_DISABLED if bus reset fails.
*
* DEPRECATED:
* This function is only for drivers which still use old EH and
* will be removed soon.
*/
void ata_bus_reset(struct ata_port *ap)
{
struct ata_device *device = ap->link.device;
struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
u8 err;
unsigned int dev0, dev1 = 0, devmask = 0;
int rc;
DPRINTK("ENTER, host %u, port %u\n", ap->print_id, ap->port_no);
/* determine if device 0/1 are present */
if (ap->flags & ATA_FLAG_SATA_RESET)
dev0 = 1;
else {
dev0 = ata_devchk(ap, 0);
if (slave_possible)
dev1 = ata_devchk(ap, 1);
}
if (dev0)
devmask |= (1 << 0);
if (dev1)
devmask |= (1 << 1);
/* select device 0 again */
ap->ops->sff_dev_select(ap, 0);
/* issue bus reset */
if (ap->flags & ATA_FLAG_SRST) {
rc = ata_bus_softreset(ap, devmask,
ata_deadline(jiffies, 40000));
if (rc && rc != -ENODEV)
goto err_out;
}
/*
* determine by signature whether we have ATA or ATAPI devices
*/
device[0].class = ata_sff_dev_classify(&device[0], dev0, &err);
if ((slave_possible) && (err != 0x81))
device[1].class = ata_sff_dev_classify(&device[1], dev1, &err);
/* is double-select really necessary? */
if (device[1].class != ATA_DEV_NONE)
ap->ops->sff_dev_select(ap, 1);
if (device[0].class != ATA_DEV_NONE)
ap->ops->sff_dev_select(ap, 0);
/* if no devices were detected, disable this port */
if ((device[0].class == ATA_DEV_NONE) &&
(device[1].class == ATA_DEV_NONE))
goto err_out;
if (ap->flags & (ATA_FLAG_SATA_RESET | ATA_FLAG_SRST)) {
/* set up device control for ATA_FLAG_SATA_RESET */
iowrite8(ap->ctl, ioaddr->ctl_addr);
}
DPRINTK("EXIT\n");
return;
err_out:
ata_port_printk(ap, KERN_ERR, "disabling port\n");
ata_port_disable(ap);
DPRINTK("EXIT\n");
}
#ifdef CONFIG_PCI
/**
* ata_pci_bmdma_clear_simplex - attempt to kick device out of simplex
* @pdev: PCI device
*
* Some PCI ATA devices report simplex mode but in fact can be told to
* enter non simplex mode. This implements the necessary logic to
* perform the task on such devices. Calling it on other devices will
* have -undefined- behaviour.
*/
int ata_pci_bmdma_clear_simplex(struct pci_dev *pdev)
{
unsigned long bmdma = pci_resource_start(pdev, 4);
u8 simplex;
if (bmdma == 0)
return -ENOENT;
simplex = inb(bmdma + 0x02);
outb(simplex & 0x60, bmdma + 0x02);
simplex = inb(bmdma + 0x02);
if (simplex & 0x80)
return -EOPNOTSUPP;
return 0;
}
/**
* ata_pci_bmdma_init - acquire PCI BMDMA resources and init ATA host
* @host: target ATA host
*
* Acquire PCI BMDMA resources and initialize @host accordingly.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_pci_bmdma_init(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
int i, rc;
/* No BAR4 allocation: No DMA */
if (pci_resource_start(pdev, 4) == 0)
return 0;
/* TODO: If we get no DMA mask we should fall back to PIO */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
/* request and iomap DMA region */
rc = pcim_iomap_regions(pdev, 1 << 4, dev_driver_string(gdev));
if (rc) {
dev_printk(KERN_ERR, gdev, "failed to request/iomap BAR4\n");
return -ENOMEM;
}
host->iomap = pcim_iomap_table(pdev);
for (i = 0; i < 2; i++) {
struct ata_port *ap = host->ports[i];
void __iomem *bmdma = host->iomap[4] + 8 * i;
if (ata_port_is_dummy(ap))
continue;
ap->ioaddr.bmdma_addr = bmdma;
if ((!(ap->flags & ATA_FLAG_IGN_SIMPLEX)) &&
(ioread8(bmdma + 2) & 0x80))
host->flags |= ATA_HOST_SIMPLEX;
ata_port_desc(ap, "bmdma 0x%llx",
(unsigned long long)pci_resource_start(pdev, 4) + 8 * i);
}
return 0;
}
static int ata_resources_present(struct pci_dev *pdev, int port)
{
int i;
/* Check the PCI resources for this channel are enabled */
port = port * 2;
for (i = 0; i < 2; i ++) {
if (pci_resource_start(pdev, port + i) == 0 ||
pci_resource_len(pdev, port + i) == 0)
return 0;
}
return 1;
}
/**
* ata_pci_sff_init_host - acquire native PCI ATA resources and init host
* @host: target ATA host
*
* Acquire native PCI ATA resources for @host and initialize the
* first two ports of @host accordingly. Ports marked dummy are
* skipped and allocation failure makes the port dummy.
*
* Note that native PCI resources are valid even for legacy hosts
* as we fix up pdev resources array early in boot, so this
* function can be used for both native and legacy SFF hosts.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
* 0 if at least one port is initialized, -ENODEV if no port is
* available.
*/
int ata_pci_sff_init_host(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
unsigned int mask = 0;
int i, rc;
/* request, iomap BARs and init port addresses accordingly */
for (i = 0; i < 2; i++) {
struct ata_port *ap = host->ports[i];
int base = i * 2;
void __iomem * const *iomap;
if (ata_port_is_dummy(ap))
continue;
/* Discard disabled ports. Some controllers show
* their unused channels this way. Disabled ports are
* made dummy.
*/
if (!ata_resources_present(pdev, i)) {
ap->ops = &ata_dummy_port_ops;
continue;
}
rc = pcim_iomap_regions(pdev, 0x3 << base,
dev_driver_string(gdev));
if (rc) {
dev_printk(KERN_WARNING, gdev,
"failed to request/iomap BARs for port %d "
"(errno=%d)\n", i, rc);
if (rc == -EBUSY)
pcim_pin_device(pdev);
ap->ops = &ata_dummy_port_ops;
continue;
}
host->iomap = iomap = pcim_iomap_table(pdev);
ap->ioaddr.cmd_addr = iomap[base];
ap->ioaddr.altstatus_addr =
ap->ioaddr.ctl_addr = (void __iomem *)
((unsigned long)iomap[base + 1] | ATA_PCI_CTL_OFS);
ata_sff_std_ports(&ap->ioaddr);
ata_port_desc(ap, "cmd 0x%llx ctl 0x%llx",
(unsigned long long)pci_resource_start(pdev, base),
(unsigned long long)pci_resource_start(pdev, base + 1));
mask |= 1 << i;
}
if (!mask) {
dev_printk(KERN_ERR, gdev, "no available native port\n");
return -ENODEV;
}
return 0;
}
/**
* ata_pci_sff_prepare_host - helper to prepare native PCI ATA host
* @pdev: target PCI device
* @ppi: array of port_info, must be enough for two ports
* @r_host: out argument for the initialized ATA host
*
* Helper to allocate ATA host for @pdev, acquire all native PCI
* resources and initialize it accordingly in one go.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_pci_sff_prepare_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct ata_host **r_host)
{
struct ata_host *host;
int rc;
if (!devres_open_group(&pdev->dev, NULL, GFP_KERNEL))
return -ENOMEM;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host) {
dev_printk(KERN_ERR, &pdev->dev,
"failed to allocate ATA host\n");
rc = -ENOMEM;
goto err_out;
}
rc = ata_pci_sff_init_host(host);
if (rc)
goto err_out;
/* init DMA related stuff */
rc = ata_pci_bmdma_init(host);
if (rc)
goto err_bmdma;
devres_remove_group(&pdev->dev, NULL);
*r_host = host;
return 0;
err_bmdma:
/* This is necessary because PCI and iomap resources are
* merged and releasing the top group won't release the
* acquired resources if some of those have been acquired
* before entering this function.
*/
pcim_iounmap_regions(pdev, 0xf);
err_out:
devres_release_group(&pdev->dev, NULL);
return rc;
}
/**
* ata_pci_sff_activate_host - start SFF host, request IRQ and register it
* @host: target SFF ATA host
* @irq_handler: irq_handler used when requesting IRQ(s)
* @sht: scsi_host_template to use when registering the host
*
* This is the counterpart of ata_host_activate() for SFF ATA
* hosts. This separate helper is necessary because SFF hosts
* use two separate interrupts in legacy mode.
*
* LOCKING:
* Inherited from calling layer (may sleep).
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int ata_pci_sff_activate_host(struct ata_host *host,
irq_handler_t irq_handler,
struct scsi_host_template *sht)
{
struct device *dev = host->dev;
struct pci_dev *pdev = to_pci_dev(dev);
const char *drv_name = dev_driver_string(host->dev);
int legacy_mode = 0, rc;
rc = ata_host_start(host);
if (rc)
return rc;
if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
u8 tmp8, mask;
/* TODO: What if one channel is in native mode ... */
pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
mask = (1 << 2) | (1 << 0);
if ((tmp8 & mask) != mask)
legacy_mode = 1;
#if defined(CONFIG_NO_ATA_LEGACY)
/* Some platforms with PCI limits cannot address compat
port space. In that case we punt if their firmware has
left a device in compatibility mode */
if (legacy_mode) {
printk(KERN_ERR "ata: Compatibility mode ATA is not supported on this platform, skipping.\n");
return -EOPNOTSUPP;
}
#endif
}
if (!devres_open_group(dev, NULL, GFP_KERNEL))
return -ENOMEM;
if (!legacy_mode && pdev->irq) {
rc = devm_request_irq(dev, pdev->irq, irq_handler,
IRQF_SHARED, drv_name, host);
if (rc)
goto out;
ata_port_desc(host->ports[0], "irq %d", pdev->irq);
ata_port_desc(host->ports[1], "irq %d", pdev->irq);
} else if (legacy_mode) {
if (!ata_port_is_dummy(host->ports[0])) {
rc = devm_request_irq(dev, ATA_PRIMARY_IRQ(pdev),
irq_handler, IRQF_SHARED,
drv_name, host);
if (rc)
goto out;
ata_port_desc(host->ports[0], "irq %d",
ATA_PRIMARY_IRQ(pdev));
}
if (!ata_port_is_dummy(host->ports[1])) {
rc = devm_request_irq(dev, ATA_SECONDARY_IRQ(pdev),
irq_handler, IRQF_SHARED,
drv_name, host);
if (rc)
goto out;
ata_port_desc(host->ports[1], "irq %d",
ATA_SECONDARY_IRQ(pdev));
}
}
rc = ata_host_register(host, sht);
out:
if (rc == 0)
devres_remove_group(dev, NULL);
else
devres_release_group(dev, NULL);
return rc;
}
/**
* ata_pci_sff_init_one - Initialize/register PCI IDE host controller
* @pdev: Controller to be initialized
* @ppi: array of port_info, must be enough for two ports
* @sht: scsi_host_template to use when registering the host
* @host_priv: host private_data
*
* This is a helper function which can be called from a driver's
* xxx_init_one() probe function if the hardware uses traditional
* IDE taskfile registers.
*
* This function calls pci_enable_device(), reserves its register
* regions, sets the dma mask, enables bus master mode, and calls
* ata_device_add()
*
* ASSUMPTION:
* Nobody makes a single channel controller that appears solely as
* the secondary legacy port on PCI.
*
* LOCKING:
* Inherited from PCI layer (may sleep).
*
* RETURNS:
* Zero on success, negative on errno-based value on error.
*/
int ata_pci_sff_init_one(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct scsi_host_template *sht, void *host_priv)
{
struct device *dev = &pdev->dev;
const struct ata_port_info *pi = NULL;
struct ata_host *host = NULL;
int i, rc;
DPRINTK("ENTER\n");
/* look up the first valid port_info */
for (i = 0; i < 2 && ppi[i]; i++) {
if (ppi[i]->port_ops != &ata_dummy_port_ops) {
pi = ppi[i];
break;
}
}
if (!pi) {
dev_printk(KERN_ERR, &pdev->dev,
"no valid port_info specified\n");
return -EINVAL;
}
if (!devres_open_group(dev, NULL, GFP_KERNEL))
return -ENOMEM;
rc = pcim_enable_device(pdev);
if (rc)
goto out;
/* prepare and activate SFF host */
rc = ata_pci_sff_prepare_host(pdev, ppi, &host);
if (rc)
goto out;
host->private_data = host_priv;
pci_set_master(pdev);
rc = ata_pci_sff_activate_host(host, ata_sff_interrupt, sht);
out:
if (rc == 0)
devres_remove_group(&pdev->dev, NULL);
else
devres_release_group(&pdev->dev, NULL);
return rc;
}
#endif /* CONFIG_PCI */
EXPORT_SYMBOL_GPL(ata_sff_port_ops);
EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
EXPORT_SYMBOL_GPL(ata_sff_qc_prep);
EXPORT_SYMBOL_GPL(ata_sff_dumb_qc_prep);
EXPORT_SYMBOL_GPL(ata_sff_dev_select);
EXPORT_SYMBOL_GPL(ata_sff_check_status);
EXPORT_SYMBOL_GPL(ata_sff_dma_pause);
EXPORT_SYMBOL_GPL(ata_sff_pause);
EXPORT_SYMBOL_GPL(ata_sff_busy_sleep);
EXPORT_SYMBOL_GPL(ata_sff_wait_ready);
EXPORT_SYMBOL_GPL(ata_sff_tf_load);
EXPORT_SYMBOL_GPL(ata_sff_tf_read);
EXPORT_SYMBOL_GPL(ata_sff_exec_command);
EXPORT_SYMBOL_GPL(ata_sff_data_xfer);
EXPORT_SYMBOL_GPL(ata_sff_data_xfer_noirq);
EXPORT_SYMBOL_GPL(ata_sff_irq_on);
EXPORT_SYMBOL_GPL(ata_sff_irq_clear);
EXPORT_SYMBOL_GPL(ata_sff_hsm_move);
EXPORT_SYMBOL_GPL(ata_sff_qc_issue);
EXPORT_SYMBOL_GPL(ata_sff_qc_fill_rtf);
EXPORT_SYMBOL_GPL(ata_sff_host_intr);
EXPORT_SYMBOL_GPL(ata_sff_interrupt);
EXPORT_SYMBOL_GPL(ata_sff_freeze);
EXPORT_SYMBOL_GPL(ata_sff_thaw);
EXPORT_SYMBOL_GPL(ata_sff_prereset);
EXPORT_SYMBOL_GPL(ata_sff_dev_classify);
EXPORT_SYMBOL_GPL(ata_sff_wait_after_reset);
EXPORT_SYMBOL_GPL(ata_sff_softreset);
EXPORT_SYMBOL_GPL(sata_sff_hardreset);
EXPORT_SYMBOL_GPL(ata_sff_postreset);
EXPORT_SYMBOL_GPL(ata_sff_error_handler);
EXPORT_SYMBOL_GPL(ata_sff_post_internal_cmd);
EXPORT_SYMBOL_GPL(ata_sff_port_start);
EXPORT_SYMBOL_GPL(ata_sff_std_ports);
EXPORT_SYMBOL_GPL(ata_bmdma_mode_filter);
EXPORT_SYMBOL_GPL(ata_bmdma_setup);
EXPORT_SYMBOL_GPL(ata_bmdma_start);
EXPORT_SYMBOL_GPL(ata_bmdma_stop);
EXPORT_SYMBOL_GPL(ata_bmdma_status);
EXPORT_SYMBOL_GPL(ata_bus_reset);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(ata_pci_bmdma_clear_simplex);
EXPORT_SYMBOL_GPL(ata_pci_bmdma_init);
EXPORT_SYMBOL_GPL(ata_pci_sff_init_host);
EXPORT_SYMBOL_GPL(ata_pci_sff_prepare_host);
EXPORT_SYMBOL_GPL(ata_pci_sff_activate_host);
EXPORT_SYMBOL_GPL(ata_pci_sff_init_one);
#endif /* CONFIG_PCI */
View Git Blame Copy Permalink