mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-22 20:23:57 +08:00
2d66eab183
IPQ8074 uses QMP PHY controller that provides support to PCIe and USB. Adding DT binding information for the same. Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
118 lines
3.6 KiB
Plaintext
118 lines
3.6 KiB
Plaintext
Qualcomm QMP PHY controller
|
|
===========================
|
|
|
|
QMP phy controller supports physical layer functionality for a number of
|
|
controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
|
|
|
|
Required properties:
|
|
- compatible: compatible list, contains:
|
|
"qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
|
|
"qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
|
|
"qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
|
|
|
|
- reg: offset and length of register set for PHY's common serdes block.
|
|
|
|
- #clock-cells: must be 1
|
|
- Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
|
|
interface (for pipe based PHYs). These clock are then gate-controlled
|
|
by gcc.
|
|
- #address-cells: must be 1
|
|
- #size-cells: must be 1
|
|
- ranges: must be present
|
|
|
|
- clocks: a list of phandles and clock-specifier pairs,
|
|
one for each entry in clock-names.
|
|
- clock-names: "cfg_ahb" for phy config clock,
|
|
"aux" for phy aux clock,
|
|
"ref" for 19.2 MHz ref clk,
|
|
For "qcom,msm8996-qmp-pcie-phy" must contain:
|
|
"aux", "cfg_ahb", "ref".
|
|
For "qcom,msm8996-qmp-usb3-phy" must contain:
|
|
"aux", "cfg_ahb", "ref".
|
|
|
|
- resets: a list of phandles and reset controller specifier pairs,
|
|
one for each entry in reset-names.
|
|
- reset-names: "phy" for reset of phy block,
|
|
"common" for phy common block reset,
|
|
"cfg" for phy's ahb cfg block reset (Optional).
|
|
For "qcom,msm8996-qmp-pcie-phy" must contain:
|
|
"phy", "common", "cfg".
|
|
For "qcom,msm8996-qmp-usb3-phy" must contain
|
|
"phy", "common".
|
|
For "qcom,ipq8074-qmp-pcie-phy" must contain:
|
|
"phy", "common".
|
|
|
|
- vdda-phy-supply: Phandle to a regulator supply to PHY core block.
|
|
- vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
|
|
|
|
Optional properties:
|
|
- vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
|
|
pll block.
|
|
|
|
Required nodes:
|
|
- Each device node of QMP phy is required to have as many child nodes as
|
|
the number of lanes the PHY has.
|
|
|
|
Required properties for child node:
|
|
- reg: list of offset and length pairs of register sets for PHY blocks -
|
|
tx, rx and pcs.
|
|
|
|
- #phy-cells: must be 0
|
|
|
|
- clocks: a list of phandles and clock-specifier pairs,
|
|
one for each entry in clock-names.
|
|
- clock-names: Must contain following for pcie and usb qmp phys:
|
|
"pipe<lane-number>" for pipe clock specific to each lane.
|
|
- clock-output-names: Name of the PHY clock that will be the parent for
|
|
the above pipe clock.
|
|
|
|
For "qcom,ipq8074-qmp-pcie-phy":
|
|
- "pcie20_phy0_pipe_clk" Pipe Clock parent
|
|
(or)
|
|
"pcie20_phy1_pipe_clk"
|
|
|
|
- resets: a list of phandles and reset controller specifier pairs,
|
|
one for each entry in reset-names.
|
|
- reset-names: Must contain following for pcie qmp phys:
|
|
"lane<lane-number>" for reset specific to each lane.
|
|
|
|
Example:
|
|
phy@34000 {
|
|
compatible = "qcom,msm8996-qmp-pcie-phy";
|
|
reg = <0x34000 0x488>;
|
|
#clock-cells = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
|
|
<&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
|
|
<&gcc GCC_PCIE_CLKREF_CLK>;
|
|
clock-names = "aux", "cfg_ahb", "ref";
|
|
|
|
vdda-phy-supply = <&pm8994_l28>;
|
|
vdda-pll-supply = <&pm8994_l12>;
|
|
|
|
resets = <&gcc GCC_PCIE_PHY_BCR>,
|
|
<&gcc GCC_PCIE_PHY_COM_BCR>,
|
|
<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
|
|
reset-names = "phy", "common", "cfg";
|
|
|
|
pciephy_0: lane@35000 {
|
|
reg = <0x35000 0x130>,
|
|
<0x35200 0x200>,
|
|
<0x35400 0x1dc>;
|
|
#phy-cells = <0>;
|
|
|
|
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
|
|
clock-names = "pipe0";
|
|
clock-output-names = "pcie_0_pipe_clk_src";
|
|
resets = <&gcc GCC_PCIE_0_PHY_BCR>;
|
|
reset-names = "lane0";
|
|
};
|
|
|
|
pciephy_1: lane@36000 {
|
|
...
|
|
...
|
|
};
|