mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-22 20:23:57 +08:00
de6e0f84be
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161, update the miphy28lp phy driver to access sysconfig register offsets via syscfg dt property. This is because the reg property should not be mixing address spaces like it does currently for miphy28lp. This change then also aligns us to how other platforms such as keystone and bcm7445 pass there syscon offsets via DT. I have updated the miphy28lp phy driver same way as Peter's implementation. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
118 lines
3.7 KiB
Plaintext
118 lines
3.7 KiB
Plaintext
STMicroelectronics STi MIPHY28LP PHY binding
|
|
============================================
|
|
|
|
This binding describes a miphy device that is used to control PHY hardware
|
|
for SATA, PCIe or USB3.
|
|
|
|
Required properties (controller (parent) node):
|
|
- compatible : Should be "st,miphy28lp-phy".
|
|
- st,syscfg : Should be a phandle of the system configuration register group
|
|
which contain the SATA, PCIe or USB3 mode setting bits.
|
|
|
|
Required nodes : A sub-node is required for each channel the controller
|
|
provides. Address range information including the usual
|
|
'reg' and 'reg-names' properties are used inside these
|
|
nodes to describe the controller's topology. These nodes
|
|
are translated by the driver's .xlate() function.
|
|
|
|
Required properties (port (child) node):
|
|
- #phy-cells : Should be 1 (See second example)
|
|
Cell after port phandle is device type from:
|
|
- PHY_TYPE_SATA
|
|
- PHY_TYPE_PCI
|
|
- PHY_TYPE_USB3
|
|
- reg : Address and length of the register set for the device.
|
|
- reg-names : The names of the register addresses corresponding to the registers
|
|
filled in "reg". It can also contain the offset of the system configuration
|
|
registers used as glue-logic to setup the device for SATA/PCIe or USB3
|
|
devices.
|
|
- st,syscfg : Offset of the parent configuration register.
|
|
- resets : phandle to the parent reset controller.
|
|
- reset-names : Associated name must be "miphy-sw-rst".
|
|
|
|
Optional properties (port (child) node):
|
|
- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This
|
|
is not available in all the MiPHY. For example, for STiH407, only the
|
|
MiPHY0 has this bit.
|
|
- st,osc-force-ext : to select the external oscillator. This can change from
|
|
different MiPHY inside the same SoC.
|
|
- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config
|
|
register.
|
|
- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive
|
|
line).
|
|
- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe).
|
|
- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values.
|
|
|
|
example:
|
|
|
|
miphy28lp_phy: miphy28lp@9b22000 {
|
|
compatible = "st,miphy28lp-phy";
|
|
st,syscfg = <&syscfg_core>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
phy_port0: port@9b22000 {
|
|
reg = <0x9b22000 0xff>,
|
|
<0x9b09000 0xff>,
|
|
<0x9b04000 0xff>;
|
|
reg-names = "sata-up",
|
|
"pcie-up",
|
|
"pipew";
|
|
|
|
st,syscfg = <0x114 0x818 0xe0 0xec>;
|
|
#phy-cells = <1>;
|
|
st,osc-rdy;
|
|
reset-names = "miphy-sw-rst";
|
|
resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
|
|
};
|
|
|
|
phy_port1: port@9b2a000 {
|
|
reg = <0x9b2a000 0xff>,
|
|
<0x9b19000 0xff>,
|
|
<0x9b14000 0xff>;
|
|
reg-names = "sata-up",
|
|
"pcie-up",
|
|
"pipew";
|
|
|
|
st,syscfg = <0x118 0x81c 0xe4 0xf0>;
|
|
|
|
#phy-cells = <1>;
|
|
st,osc-force-ext;
|
|
reset-names = "miphy-sw-rst";
|
|
resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
|
|
};
|
|
|
|
phy_port2: port@8f95000 {
|
|
reg = <0x8f95000 0xff>,
|
|
<0x8f90000 0xff>;
|
|
reg-names = "pipew",
|
|
"usb3-up";
|
|
|
|
st,syscfg = <0x11c 0x820>;
|
|
|
|
#phy-cells = <1>;
|
|
reset-names = "miphy-sw-rst";
|
|
resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
|
|
};
|
|
};
|
|
|
|
|
|
Specifying phy control of devices
|
|
=================================
|
|
|
|
Device nodes should specify the configuration required in their "phys"
|
|
property, containing a phandle to the miphy device node and an index
|
|
specifying which configuration to use, as described in phy-bindings.txt.
|
|
|
|
example:
|
|
sata0: sata@9b20000 {
|
|
...
|
|
phys = <&phy_port0 PHY_TYPE_SATA>;
|
|
...
|
|
};
|
|
|
|
Macro definitions for the supported miphy configuration can be found in:
|
|
|
|
include/dt-bindings/phy/phy.h
|