mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-22 20:23:57 +08:00
4da722ca19
Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org>
107 lines
2.2 KiB
Plaintext
107 lines
2.2 KiB
Plaintext
Texas Instruments VPIF
|
|
----------------------
|
|
|
|
The TI Video Port InterFace (VPIF) is the primary component for video
|
|
capture and display on the DA850/AM18x family of TI DaVinci/Sitara
|
|
SoCs.
|
|
|
|
TI Document reference: SPRUH82C, Chapter 35
|
|
http://www.ti.com/lit/pdf/spruh82
|
|
|
|
Required properties:
|
|
- compatible: must be "ti,da850-vpif"
|
|
- reg: physical base address and length of the registers set for the device;
|
|
- interrupts: should contain IRQ line for the VPIF
|
|
|
|
Video Capture:
|
|
|
|
VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
|
|
single 16-bit channel. It should contain one or two port child nodes
|
|
with child 'endpoint' node. If there are two ports then port@0 must
|
|
describe the input and port@1 output channels. Please refer to the
|
|
bindings defined in
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt.
|
|
|
|
Example using 2 8-bit input channels, one of which is connected to an
|
|
I2C-connected TVP5147 decoder:
|
|
|
|
vpif: vpif@217000 {
|
|
compatible = "ti,da850-vpif";
|
|
reg = <0x217000 0x1000>;
|
|
interrupts = <92>;
|
|
|
|
port@0 {
|
|
vpif_input_ch0: endpoint@0 {
|
|
reg = <0>;
|
|
bus-width = <8>;
|
|
remote-endpoint = <&composite_in>;
|
|
};
|
|
|
|
vpif_input_ch1: endpoint@1 {
|
|
reg = <1>;
|
|
bus-width = <8>;
|
|
data-shift = <8>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
vpif_output_ch0: endpoint {
|
|
bus-width = <8>;
|
|
remote-endpoint = <&composite_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
[ ... ]
|
|
|
|
&i2c0 {
|
|
|
|
tvp5147@5d {
|
|
compatible = "ti,tvp5147";
|
|
reg = <0x5d>;
|
|
|
|
port {
|
|
composite_in: endpoint {
|
|
hsync-active = <1>;
|
|
vsync-active = <1>;
|
|
pclk-sample = <0>;
|
|
|
|
/* VPIF channel 0 (lower 8-bits) */
|
|
remote-endpoint = <&vpif_input_ch0>;
|
|
bus-width = <8>;
|
|
};
|
|
};
|
|
};
|
|
|
|
adv7343@2a {
|
|
compatible = "adi,adv7343";
|
|
reg = <0x2a>;
|
|
|
|
port {
|
|
composite_out: endpoint {
|
|
adi,dac-enable = <1 1 1>;
|
|
adi,sd-dac-enable = <1>;
|
|
|
|
remote-endpoint = <&vpif_output_ch0>;
|
|
bus-width = <8>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
|
|
Alternatively, an example when the bus is configured as a single
|
|
16-bit input (e.g. for raw-capture mode):
|
|
|
|
vpif: vpif@217000 {
|
|
compatible = "ti,da850-vpif";
|
|
reg = <0x217000 0x1000>;
|
|
interrupts = <92>;
|
|
|
|
port {
|
|
vpif_ch0: endpoint {
|
|
bus-width = <16>;
|
|
};
|
|
};
|
|
};
|