renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-29 15:43:59 +08:00
Code
9b2dcba3aa
linux-next/drivers/scsi/mpt3sas/mpi/mpi2_cnfg.h
Sreekanth Reddy 17263e754d [SCSI] mpt3sas: MPI2.5 Rev F v2.5.1.1 specification 
Change set in MPI v2.5 Rev F(v2.5.1.1) specification and 2.00.29 header files

1. Added a bit to the IOCExceptions field of the IOCFacts Reply to indicate
   that the IOC detected a partial memory failure.
2. Added ElapsedSeconds field to RAID Volume Indicator Structure. Added
   Elapsed Seconds Valid flag to Flags field of this structure.
3. Added ElapsedSeconds field to Integrated RAID Operations Status Event Data.
4. Added two new AbortType values for TargetModeAbort Request, one to abort
   all I/Os from a single initiator, and the other to abort only Command IUs.
5. Added a new chapter covering DMA Flags and Multicast Modes.
6. In the IOCSettings field of BIOS Page 1, modified the Adapter Support bits
   description to specify X86 BIOS.
7. Marked bit 0 of the ControlFlags field of SAS IO Unit Page 1 as
   obsolete. This was the Clear SATA Affiliation flag.
8. Added additional requirements for certain IOCs that support more than eight
   MSI-x vectors.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-07-09 08:52:53 +01:00

3335 lines
137 KiB
C
Raw Blame History

/*
* Copyright (c) 2000-2013 LSI Corporation.
*
*
* Name: mpi2_cnfg.h
* Title: MPI Configuration messages and pages
* Creation Date: November 10, 2006
*
* mpi2_cnfg.h Version: 02.00.24
*
* NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25
* prefix are for use only on MPI v2.5 products, and must not be used
* with MPI v2.0 products. Unless otherwise noted, names beginning with
* MPI2 or Mpi2 are for use with both MPI v2.0 and MPI v2.5 products.
*
* Version History
* ---------------
*
* Date Version Description
* -------- -------- ------------------------------------------------------
* 04-30-07 02.00.00 Corresponds to Fusion-MPT MPI Specification Rev A.
* 06-04-07 02.00.01 Added defines for SAS IO Unit Page 2 PhyFlags.
* Added Manufacturing Page 11.
* Added MPI2_SAS_EXPANDER0_FLAGS_CONNECTOR_END_DEVICE
* define.
* 06-26-07 02.00.02 Adding generic structure for product-specific
* Manufacturing pages: MPI2_CONFIG_PAGE_MANUFACTURING_PS.
* Rework of BIOS Page 2 configuration page.
* Fixed MPI2_BIOSPAGE2_BOOT_DEVICE to be a union of the
* forms.
* Added configuration pages IOC Page 8 and Driver
* Persistent Mapping Page 0.
* 08-31-07 02.00.03 Modified configuration pages dealing with Integrated
* RAID (Manufacturing Page 4, RAID Volume Pages 0 and 1,
* RAID Physical Disk Pages 0 and 1, RAID Configuration
* Page 0).
* Added new value for AccessStatus field of SAS Device
* Page 0 (_SATA_NEEDS_INITIALIZATION).
* 10-31-07 02.00.04 Added missing SEPDevHandle field to
* MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
* 12-18-07 02.00.05 Modified IO Unit Page 0 to use 32-bit version fields for
* NVDATA.
* Modified IOC Page 7 to use masks and added field for
* SASBroadcastPrimitiveMasks.
* Added MPI2_CONFIG_PAGE_BIOS_4.
* Added MPI2_CONFIG_PAGE_LOG_0.
* 02-29-08 02.00.06 Modified various names to make them 32-character unique.
* Added SAS Device IDs.
* Updated Integrated RAID configuration pages including
* Manufacturing Page 4, IOC Page 6, and RAID Configuration
* Page 0.
* 05-21-08 02.00.07 Added define MPI2_MANPAGE4_MIX_SSD_SAS_SATA.
* Added define MPI2_MANPAGE4_PHYSDISK_128MB_COERCION.
* Fixed define MPI2_IOCPAGE8_FLAGS_ENCLOSURE_SLOT_MAPPING.
* Added missing MaxNumRoutedSasAddresses field to
* MPI2_CONFIG_PAGE_EXPANDER_0.
* Added SAS Port Page 0.
* Modified structure layout for
* MPI2_CONFIG_PAGE_DRIVER_MAPPING_0.
* 06-27-08 02.00.08 Changed MPI2_CONFIG_PAGE_RD_PDISK_1 to use
* MPI2_RAID_PHYS_DISK1_PATH_MAX to size the array.
* 10-02-08 02.00.09 Changed MPI2_RAID_PGAD_CONFIGNUM_MASK from 0x0000FFFF
* to 0x000000FF.
* Added two new values for the Physical Disk Coercion Size
* bits in the Flags field of Manufacturing Page 4.
* Added product-specific Manufacturing pages 16 to 31.
* Modified Flags bits for controlling write cache on SATA
* drives in IO Unit Page 1.
* Added new bit to AdditionalControlFlags of SAS IO Unit
* Page 1 to control Invalid Topology Correction.
* Added additional defines for RAID Volume Page 0
* VolumeStatusFlags field.
* Modified meaning of RAID Volume Page 0 VolumeSettings
* define for auto-configure of hot-swap drives.
* Added SupportedPhysDisks field to RAID Volume Page 1 and
* added related defines.
* Added PhysDiskAttributes field (and related defines) to
* RAID Physical Disk Page 0.
* Added MPI2_SAS_PHYINFO_PHY_VACANT define.
* Added three new DiscoveryStatus bits for SAS IO Unit
* Page 0 and SAS Expander Page 0.
* Removed multiplexing information from SAS IO Unit pages.
* Added BootDeviceWaitTime field to SAS IO Unit Page 4.
* Removed Zone Address Resolved bit from PhyInfo and from
* Expander Page 0 Flags field.
* Added two new AccessStatus values to SAS Device Page 0
* for indicating routing problems. Added 3 reserved words
* to this page.
* 01-19-09 02.00.10 Fixed defines for GPIOVal field of IO Unit Page 3.
* Inserted missing reserved field into structure for IOC
* Page 6.
* Added more pending task bits to RAID Volume Page 0
* VolumeStatusFlags defines.
* Added MPI2_PHYSDISK0_STATUS_FLAG_NOT_CERTIFIED define.
* Added a new DiscoveryStatus bit for SAS IO Unit Page 0
* and SAS Expander Page 0 to flag a downstream initiator
* when in simplified routing mode.
* Removed SATA Init Failure defines for DiscoveryStatus
* fields of SAS IO Unit Page 0 and SAS Expander Page 0.
* Added MPI2_SAS_DEVICE0_ASTATUS_DEVICE_BLOCKED define.
* Added PortGroups, DmaGroup, and ControlGroup fields to
* SAS Device Page 0.
* 05-06-09 02.00.11 Added structures and defines for IO Unit Page 5 and IO
* Unit Page 6.
* Added expander reduced functionality data to SAS
* Expander Page 0.
* Added SAS PHY Page 2 and SAS PHY Page 3.
* 07-30-09 02.00.12 Added IO Unit Page 7.
* Added new device ids.
* Added SAS IO Unit Page 5.
* Added partial and slumber power management capable flags
* to SAS Device Page 0 Flags field.
* Added PhyInfo defines for power condition.
* Added Ethernet configuration pages.
* 10-28-09 02.00.13 Added MPI2_IOUNITPAGE1_ENABLE_HOST_BASED_DISCOVERY.
* Added SAS PHY Page 4 structure and defines.
* 02-10-10 02.00.14 Modified the comments for the configuration page
* structures that contain an array of data. The host
* should use the "count" field in the page data (e.g. the
* NumPhys field) to determine the number of valid elements
* in the array.
* Added/modified some MPI2_MFGPAGE_DEVID_SAS defines.
* Added PowerManagementCapabilities to IO Unit Page 7.
* Added PortWidthModGroup field to
* MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS.
* Added MPI2_CONFIG_PAGE_SASIOUNIT_6 and related defines.
* Added MPI2_CONFIG_PAGE_SASIOUNIT_7 and related defines.
* Added MPI2_CONFIG_PAGE_SASIOUNIT_8 and related defines.
* 05-12-10 02.00.15 Added MPI2_RAIDVOL0_STATUS_FLAG_VOL_NOT_CONSISTENT
* define.
* Added MPI2_PHYSDISK0_INCOMPATIBLE_MEDIA_TYPE define.
* Added MPI2_SAS_NEG_LINK_RATE_UNSUPPORTED_PHY define.
* 08-11-10 02.00.16 Removed IO Unit Page 1 device path (multi-pathing)
* defines.
* 11-10-10 02.00.17 Added ReceptacleID field (replacing Reserved1) to
* MPI2_MANPAGE7_CONNECTOR_INFO and reworked defines for
* the Pinout field.
* Added BoardTemperature and BoardTemperatureUnits fields
* to MPI2_CONFIG_PAGE_IO_UNIT_7.
* Added MPI2_CONFIG_EXTPAGETYPE_EXT_MANUFACTURING define
* and MPI2_CONFIG_PAGE_EXT_MAN_PS structure.
* 02-23-11 02.00.18 Added ProxyVF_ID field to MPI2_CONFIG_REQUEST.
* Added IO Unit Page 8, IO Unit Page 9,
* and IO Unit Page 10.
* Added SASNotifyPrimitiveMasks field to
* MPI2_CONFIG_PAGE_IOC_7.
* 03-09-11 02.00.19 Fixed IO Unit Page 10 (to match the spec).
* 05-25-11 02.00.20 Cleaned up a few comments.
* 08-24-11 02.00.21 Marked the IO Unit Page 7 PowerManagementCapabilities
* for PCIe link as obsolete.
* Added SpinupFlags field containing a Disable Spin-up bit
* to the MPI2_SAS_IOUNIT4_SPINUP_GROUP fields of SAS IO
* Unit Page 4.
* 11-18-11 02.00.22 Added define MPI2_IOCPAGE6_CAP_FLAGS_4K_SECTORS_SUPPORT.
* Added UEFIVersion field to BIOS Page 1 and defined new
* BiosOptions bits.
* Incorporating additions for MPI v2.5.
* 11-27-12 02.00.23 Added MPI2_MANPAGE7_FLAG_EVENTREPLAY_SLOT_ORDER.
* Added MPI2_BIOSPAGE1_OPTIONS_MASK_OEM_ID.
* 12-20-12 02.00.24 Marked MPI2_SASIOUNIT1_CONTROL_CLEAR_AFFILIATION as
* obsolete for MPI v2.5 and later.
* Added some defines for 12G SAS speeds.
* --------------------------------------------------------------------------
*/
#ifndef MPI2_CNFG_H
#define MPI2_CNFG_H
/*****************************************************************************
* Configuration Page Header and defines
*****************************************************************************/
/*Config Page Header */
typedef struct _MPI2_CONFIG_PAGE_HEADER {
U8 PageVersion; /*0x00 */
U8 PageLength; /*0x01 */
U8 PageNumber; /*0x02 */
U8 PageType; /*0x03 */
} MPI2_CONFIG_PAGE_HEADER, *PTR_MPI2_CONFIG_PAGE_HEADER,
Mpi2ConfigPageHeader_t, *pMpi2ConfigPageHeader_t;
typedef union _MPI2_CONFIG_PAGE_HEADER_UNION {
MPI2_CONFIG_PAGE_HEADER Struct;
U8 Bytes[4];
U16 Word16[2];
U32 Word32;
} MPI2_CONFIG_PAGE_HEADER_UNION, *PTR_MPI2_CONFIG_PAGE_HEADER_UNION,
Mpi2ConfigPageHeaderUnion, *pMpi2ConfigPageHeaderUnion;
/*Extended Config Page Header */
typedef struct _MPI2_CONFIG_EXTENDED_PAGE_HEADER {
U8 PageVersion; /*0x00 */
U8 Reserved1; /*0x01 */
U8 PageNumber; /*0x02 */
U8 PageType; /*0x03 */
U16 ExtPageLength; /*0x04 */
U8 ExtPageType; /*0x06 */
U8 Reserved2; /*0x07 */
} MPI2_CONFIG_EXTENDED_PAGE_HEADER,
*PTR_MPI2_CONFIG_EXTENDED_PAGE_HEADER,
Mpi2ConfigExtendedPageHeader_t,
*pMpi2ConfigExtendedPageHeader_t;
typedef union _MPI2_CONFIG_EXT_PAGE_HEADER_UNION {
MPI2_CONFIG_PAGE_HEADER Struct;
MPI2_CONFIG_EXTENDED_PAGE_HEADER Ext;
U8 Bytes[8];
U16 Word16[4];
U32 Word32[2];
} MPI2_CONFIG_EXT_PAGE_HEADER_UNION,
*PTR_MPI2_CONFIG_EXT_PAGE_HEADER_UNION,
Mpi2ConfigPageExtendedHeaderUnion,
*pMpi2ConfigPageExtendedHeaderUnion;
/*PageType field values */
#define MPI2_CONFIG_PAGEATTR_READ_ONLY (0x00)
#define MPI2_CONFIG_PAGEATTR_CHANGEABLE (0x10)
#define MPI2_CONFIG_PAGEATTR_PERSISTENT (0x20)
#define MPI2_CONFIG_PAGEATTR_MASK (0xF0)
#define MPI2_CONFIG_PAGETYPE_IO_UNIT (0x00)
#define MPI2_CONFIG_PAGETYPE_IOC (0x01)
#define MPI2_CONFIG_PAGETYPE_BIOS (0x02)
#define MPI2_CONFIG_PAGETYPE_RAID_VOLUME (0x08)
#define MPI2_CONFIG_PAGETYPE_MANUFACTURING (0x09)
#define MPI2_CONFIG_PAGETYPE_RAID_PHYSDISK (0x0A)
#define MPI2_CONFIG_PAGETYPE_EXTENDED (0x0F)
#define MPI2_CONFIG_PAGETYPE_MASK (0x0F)
#define MPI2_CONFIG_TYPENUM_MASK (0x0FFF)
/*ExtPageType field values */
#define MPI2_CONFIG_EXTPAGETYPE_SAS_IO_UNIT (0x10)
#define MPI2_CONFIG_EXTPAGETYPE_SAS_EXPANDER (0x11)
#define MPI2_CONFIG_EXTPAGETYPE_SAS_DEVICE (0x12)
#define MPI2_CONFIG_EXTPAGETYPE_SAS_PHY (0x13)
#define MPI2_CONFIG_EXTPAGETYPE_LOG (0x14)
#define MPI2_CONFIG_EXTPAGETYPE_ENCLOSURE (0x15)
#define MPI2_CONFIG_EXTPAGETYPE_RAID_CONFIG (0x16)
#define MPI2_CONFIG_EXTPAGETYPE_DRIVER_MAPPING (0x17)
#define MPI2_CONFIG_EXTPAGETYPE_SAS_PORT (0x18)
#define MPI2_CONFIG_EXTPAGETYPE_ETHERNET (0x19)
#define MPI2_CONFIG_EXTPAGETYPE_EXT_MANUFACTURING (0x1A)
/*****************************************************************************
* PageAddress defines
*****************************************************************************/
/*RAID Volume PageAddress format */
#define MPI2_RAID_VOLUME_PGAD_FORM_MASK (0xF0000000)
#define MPI2_RAID_VOLUME_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
#define MPI2_RAID_VOLUME_PGAD_FORM_HANDLE (0x10000000)
#define MPI2_RAID_VOLUME_PGAD_HANDLE_MASK (0x0000FFFF)
/*RAID Physical Disk PageAddress format */
#define MPI2_PHYSDISK_PGAD_FORM_MASK (0xF0000000)
#define MPI2_PHYSDISK_PGAD_FORM_GET_NEXT_PHYSDISKNUM (0x00000000)
#define MPI2_PHYSDISK_PGAD_FORM_PHYSDISKNUM (0x10000000)
#define MPI2_PHYSDISK_PGAD_FORM_DEVHANDLE (0x20000000)
#define MPI2_PHYSDISK_PGAD_PHYSDISKNUM_MASK (0x000000FF)
#define MPI2_PHYSDISK_PGAD_DEVHANDLE_MASK (0x0000FFFF)
/*SAS Expander PageAddress format */
#define MPI2_SAS_EXPAND_PGAD_FORM_MASK (0xF0000000)
#define MPI2_SAS_EXPAND_PGAD_FORM_GET_NEXT_HNDL (0x00000000)
#define MPI2_SAS_EXPAND_PGAD_FORM_HNDL_PHY_NUM (0x10000000)
#define MPI2_SAS_EXPAND_PGAD_FORM_HNDL (0x20000000)
#define MPI2_SAS_EXPAND_PGAD_HANDLE_MASK (0x0000FFFF)
#define MPI2_SAS_EXPAND_PGAD_PHYNUM_MASK (0x00FF0000)
#define MPI2_SAS_EXPAND_PGAD_PHYNUM_SHIFT (16)
/*SAS Device PageAddress format */
#define MPI2_SAS_DEVICE_PGAD_FORM_MASK (0xF0000000)
#define MPI2_SAS_DEVICE_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
#define MPI2_SAS_DEVICE_PGAD_FORM_HANDLE (0x20000000)
#define MPI2_SAS_DEVICE_PGAD_HANDLE_MASK (0x0000FFFF)
/*SAS PHY PageAddress format */
#define MPI2_SAS_PHY_PGAD_FORM_MASK (0xF0000000)
#define MPI2_SAS_PHY_PGAD_FORM_PHY_NUMBER (0x00000000)
#define MPI2_SAS_PHY_PGAD_FORM_PHY_TBL_INDEX (0x10000000)
#define MPI2_SAS_PHY_PGAD_PHY_NUMBER_MASK (0x000000FF)
#define MPI2_SAS_PHY_PGAD_PHY_TBL_INDEX_MASK (0x0000FFFF)
/*SAS Port PageAddress format */
#define MPI2_SASPORT_PGAD_FORM_MASK (0xF0000000)
#define MPI2_SASPORT_PGAD_FORM_GET_NEXT_PORT (0x00000000)
#define MPI2_SASPORT_PGAD_FORM_PORT_NUM (0x10000000)
#define MPI2_SASPORT_PGAD_PORTNUMBER_MASK (0x00000FFF)
/*SAS Enclosure PageAddress format */
#define MPI2_SAS_ENCLOS_PGAD_FORM_MASK (0xF0000000)
#define MPI2_SAS_ENCLOS_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
#define MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE (0x10000000)
#define MPI2_SAS_ENCLOS_PGAD_HANDLE_MASK (0x0000FFFF)
/*RAID Configuration PageAddress format */
#define MPI2_RAID_PGAD_FORM_MASK (0xF0000000)
#define MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM (0x00000000)
#define MPI2_RAID_PGAD_FORM_CONFIGNUM (0x10000000)
#define MPI2_RAID_PGAD_FORM_ACTIVE_CONFIG (0x20000000)
#define MPI2_RAID_PGAD_CONFIGNUM_MASK (0x000000FF)
/*Driver Persistent Mapping PageAddress format */
#define MPI2_DPM_PGAD_FORM_MASK (0xF0000000)
#define MPI2_DPM_PGAD_FORM_ENTRY_RANGE (0x00000000)
#define MPI2_DPM_PGAD_ENTRY_COUNT_MASK (0x0FFF0000)
#define MPI2_DPM_PGAD_ENTRY_COUNT_SHIFT (16)
#define MPI2_DPM_PGAD_START_ENTRY_MASK (0x0000FFFF)
/*Ethernet PageAddress format */
#define MPI2_ETHERNET_PGAD_FORM_MASK (0xF0000000)
#define MPI2_ETHERNET_PGAD_FORM_IF_NUM (0x00000000)
#define MPI2_ETHERNET_PGAD_IF_NUMBER_MASK (0x000000FF)
/****************************************************************************
* Configuration messages
****************************************************************************/
/*Configuration Request Message */
typedef struct _MPI2_CONFIG_REQUEST {
U8 Action; /*0x00 */
U8 SGLFlags; /*0x01 */
U8 ChainOffset; /*0x02 */
U8 Function; /*0x03 */
U16 ExtPageLength; /*0x04 */
U8 ExtPageType; /*0x06 */
U8 MsgFlags; /*0x07 */
U8 VP_ID; /*0x08 */
U8 VF_ID; /*0x09 */
U16 Reserved1; /*0x0A */
U8 Reserved2; /*0x0C */
U8 ProxyVF_ID; /*0x0D */
U16 Reserved4; /*0x0E */
U32 Reserved3; /*0x10 */
MPI2_CONFIG_PAGE_HEADER Header; /*0x14 */
U32 PageAddress; /*0x18 */
MPI2_SGE_IO_UNION PageBufferSGE; /*0x1C */
} MPI2_CONFIG_REQUEST, *PTR_MPI2_CONFIG_REQUEST,
Mpi2ConfigRequest_t, *pMpi2ConfigRequest_t;
/*values for the Action field */
#define MPI2_CONFIG_ACTION_PAGE_HEADER (0x00)
#define MPI2_CONFIG_ACTION_PAGE_READ_CURRENT (0x01)
#define MPI2_CONFIG_ACTION_PAGE_WRITE_CURRENT (0x02)
#define MPI2_CONFIG_ACTION_PAGE_DEFAULT (0x03)
#define MPI2_CONFIG_ACTION_PAGE_WRITE_NVRAM (0x04)
#define MPI2_CONFIG_ACTION_PAGE_READ_DEFAULT (0x05)
#define MPI2_CONFIG_ACTION_PAGE_READ_NVRAM (0x06)
#define MPI2_CONFIG_ACTION_PAGE_GET_CHANGEABLE (0x07)
/*use MPI2_SGLFLAGS_ defines from mpi2.h for the SGLFlags field */
/*Config Reply Message */
typedef struct _MPI2_CONFIG_REPLY {
U8 Action; /*0x00 */
U8 SGLFlags; /*0x01 */
U8 MsgLength; /*0x02 */
U8 Function; /*0x03 */
U16 ExtPageLength; /*0x04 */
U8 ExtPageType; /*0x06 */
U8 MsgFlags; /*0x07 */
U8 VP_ID; /*0x08 */
U8 VF_ID; /*0x09 */
U16 Reserved1; /*0x0A */
U16 Reserved2; /*0x0C */
U16 IOCStatus; /*0x0E */
U32 IOCLogInfo; /*0x10 */
MPI2_CONFIG_PAGE_HEADER Header; /*0x14 */
} MPI2_CONFIG_REPLY, *PTR_MPI2_CONFIG_REPLY,
Mpi2ConfigReply_t, *pMpi2ConfigReply_t;
/*****************************************************************************
*
* C o n f i g u r a t i o n P a g e s
*
*****************************************************************************/
/****************************************************************************
* Manufacturing Config pages
****************************************************************************/
#define MPI2_MFGPAGE_VENDORID_LSI (0x1000)
/*MPI v2.0 SAS products */
#define MPI2_MFGPAGE_DEVID_SAS2004 (0x0070)
#define MPI2_MFGPAGE_DEVID_SAS2008 (0x0072)
#define MPI2_MFGPAGE_DEVID_SAS2108_1 (0x0074)
#define MPI2_MFGPAGE_DEVID_SAS2108_2 (0x0076)
#define MPI2_MFGPAGE_DEVID_SAS2108_3 (0x0077)
#define MPI2_MFGPAGE_DEVID_SAS2116_1 (0x0064)
#define MPI2_MFGPAGE_DEVID_SAS2116_2 (0x0065)
#define MPI2_MFGPAGE_DEVID_SSS6200 (0x007E)
#define MPI2_MFGPAGE_DEVID_SAS2208_1 (0x0080)
#define MPI2_MFGPAGE_DEVID_SAS2208_2 (0x0081)
#define MPI2_MFGPAGE_DEVID_SAS2208_3 (0x0082)
#define MPI2_MFGPAGE_DEVID_SAS2208_4 (0x0083)
#define MPI2_MFGPAGE_DEVID_SAS2208_5 (0x0084)
#define MPI2_MFGPAGE_DEVID_SAS2208_6 (0x0085)
#define MPI2_MFGPAGE_DEVID_SAS2308_1 (0x0086)
#define MPI2_MFGPAGE_DEVID_SAS2308_2 (0x0087)
#define MPI2_MFGPAGE_DEVID_SAS2308_3 (0x006E)
/*MPI v2.5 SAS products */
#define MPI25_MFGPAGE_DEVID_SAS3004 (0x0096)
#define MPI25_MFGPAGE_DEVID_SAS3008 (0x0097)
#define MPI25_MFGPAGE_DEVID_SAS3108_1 (0x0090)
#define MPI25_MFGPAGE_DEVID_SAS3108_2 (0x0091)
#define MPI25_MFGPAGE_DEVID_SAS3108_5 (0x0094)
#define MPI25_MFGPAGE_DEVID_SAS3108_6 (0x0095)
/*Manufacturing Page 0 */
typedef struct _MPI2_CONFIG_PAGE_MAN_0 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 ChipName[16]; /*0x04 */
U8 ChipRevision[8]; /*0x14 */
U8 BoardName[16]; /*0x1C */
U8 BoardAssembly[16]; /*0x2C */
U8 BoardTracerNumber[16]; /*0x3C */
} MPI2_CONFIG_PAGE_MAN_0,
*PTR_MPI2_CONFIG_PAGE_MAN_0,
Mpi2ManufacturingPage0_t,
*pMpi2ManufacturingPage0_t;
#define MPI2_MANUFACTURING0_PAGEVERSION (0x00)
/*Manufacturing Page 1 */
typedef struct _MPI2_CONFIG_PAGE_MAN_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 VPD[256]; /*0x04 */
} MPI2_CONFIG_PAGE_MAN_1,
*PTR_MPI2_CONFIG_PAGE_MAN_1,
Mpi2ManufacturingPage1_t,
*pMpi2ManufacturingPage1_t;
#define MPI2_MANUFACTURING1_PAGEVERSION (0x00)
typedef struct _MPI2_CHIP_REVISION_ID {
U16 DeviceID; /*0x00 */
U8 PCIRevisionID; /*0x02 */
U8 Reserved; /*0x03 */
} MPI2_CHIP_REVISION_ID, *PTR_MPI2_CHIP_REVISION_ID,
Mpi2ChipRevisionId_t, *pMpi2ChipRevisionId_t;
/*Manufacturing Page 2 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check Header.PageLength at runtime.
*/
#ifndef MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS
#define MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_MAN_2 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
MPI2_CHIP_REVISION_ID ChipId; /*0x04 */
U32
HwSettings[MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS];/*0x08 */
} MPI2_CONFIG_PAGE_MAN_2,
*PTR_MPI2_CONFIG_PAGE_MAN_2,
Mpi2ManufacturingPage2_t,
*pMpi2ManufacturingPage2_t;
#define MPI2_MANUFACTURING2_PAGEVERSION (0x00)
/*Manufacturing Page 3 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check Header.PageLength at runtime.
*/
#ifndef MPI2_MAN_PAGE_3_INFO_WORDS
#define MPI2_MAN_PAGE_3_INFO_WORDS (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_MAN_3 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
MPI2_CHIP_REVISION_ID ChipId; /*0x04 */
U32
Info[MPI2_MAN_PAGE_3_INFO_WORDS];/*0x08 */
} MPI2_CONFIG_PAGE_MAN_3,
*PTR_MPI2_CONFIG_PAGE_MAN_3,
Mpi2ManufacturingPage3_t,
*pMpi2ManufacturingPage3_t;
#define MPI2_MANUFACTURING3_PAGEVERSION (0x00)
/*Manufacturing Page 4 */
typedef struct _MPI2_MANPAGE4_PWR_SAVE_SETTINGS {
U8 PowerSaveFlags; /*0x00 */
U8 InternalOperationsSleepTime; /*0x01 */
U8 InternalOperationsRunTime; /*0x02 */
U8 HostIdleTime; /*0x03 */
} MPI2_MANPAGE4_PWR_SAVE_SETTINGS,
*PTR_MPI2_MANPAGE4_PWR_SAVE_SETTINGS,
Mpi2ManPage4PwrSaveSettings_t,
*pMpi2ManPage4PwrSaveSettings_t;
/*defines for the PowerSaveFlags field */
#define MPI2_MANPAGE4_MASK_POWERSAVE_MODE (0x03)
#define MPI2_MANPAGE4_POWERSAVE_MODE_DISABLED (0x00)
#define MPI2_MANPAGE4_CUSTOM_POWERSAVE_MODE (0x01)
#define MPI2_MANPAGE4_FULL_POWERSAVE_MODE (0x02)
typedef struct _MPI2_CONFIG_PAGE_MAN_4 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Flags; /*0x08 */
U8 InquirySize; /*0x0C */
U8 Reserved2; /*0x0D */
U16 Reserved3; /*0x0E */
U8 InquiryData[56]; /*0x10 */
U32 RAID0VolumeSettings; /*0x48 */
U32 RAID1EVolumeSettings; /*0x4C */
U32 RAID1VolumeSettings; /*0x50 */
U32 RAID10VolumeSettings; /*0x54 */
U32 Reserved4; /*0x58 */
U32 Reserved5; /*0x5C */
MPI2_MANPAGE4_PWR_SAVE_SETTINGS PowerSaveSettings; /*0x60 */
U8 MaxOCEDisks; /*0x64 */
U8 ResyncRate; /*0x65 */
U16 DataScrubDuration; /*0x66 */
U8 MaxHotSpares; /*0x68 */
U8 MaxPhysDisksPerVol; /*0x69 */
U8 MaxPhysDisks; /*0x6A */
U8 MaxVolumes; /*0x6B */
} MPI2_CONFIG_PAGE_MAN_4,
*PTR_MPI2_CONFIG_PAGE_MAN_4,
Mpi2ManufacturingPage4_t,
*pMpi2ManufacturingPage4_t;
#define MPI2_MANUFACTURING4_PAGEVERSION (0x0A)
/*Manufacturing Page 4 Flags field */
#define MPI2_MANPAGE4_METADATA_SIZE_MASK (0x00030000)
#define MPI2_MANPAGE4_METADATA_512MB (0x00000000)
#define MPI2_MANPAGE4_MIX_SSD_SAS_SATA (0x00008000)
#define MPI2_MANPAGE4_MIX_SSD_AND_NON_SSD (0x00004000)
#define MPI2_MANPAGE4_HIDE_PHYSDISK_NON_IR (0x00002000)
#define MPI2_MANPAGE4_MASK_PHYSDISK_COERCION (0x00001C00)
#define MPI2_MANPAGE4_PHYSDISK_COERCION_1GB (0x00000000)
#define MPI2_MANPAGE4_PHYSDISK_128MB_COERCION (0x00000400)
#define MPI2_MANPAGE4_PHYSDISK_ADAPTIVE_COERCION (0x00000800)
#define MPI2_MANPAGE4_PHYSDISK_ZERO_COERCION (0x00000C00)
#define MPI2_MANPAGE4_MASK_BAD_BLOCK_MARKING (0x00000300)
#define MPI2_MANPAGE4_DEFAULT_BAD_BLOCK_MARKING (0x00000000)
#define MPI2_MANPAGE4_TABLE_BAD_BLOCK_MARKING (0x00000100)
#define MPI2_MANPAGE4_WRITE_LONG_BAD_BLOCK_MARKING (0x00000200)
#define MPI2_MANPAGE4_FORCE_OFFLINE_FAILOVER (0x00000080)
#define MPI2_MANPAGE4_RAID10_DISABLE (0x00000040)
#define MPI2_MANPAGE4_RAID1E_DISABLE (0x00000020)
#define MPI2_MANPAGE4_RAID1_DISABLE (0x00000010)
#define MPI2_MANPAGE4_RAID0_DISABLE (0x00000008)
#define MPI2_MANPAGE4_IR_MODEPAGE8_DISABLE (0x00000004)
#define MPI2_MANPAGE4_IM_RESYNC_CACHE_ENABLE (0x00000002)
#define MPI2_MANPAGE4_IR_NO_MIX_SAS_SATA (0x00000001)
/*Manufacturing Page 5 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_MAN_PAGE_5_PHY_ENTRIES
#define MPI2_MAN_PAGE_5_PHY_ENTRIES (1)
#endif
typedef struct _MPI2_MANUFACTURING5_ENTRY {
U64 WWID; /*0x00 */
U64 DeviceName; /*0x08 */
} MPI2_MANUFACTURING5_ENTRY,
*PTR_MPI2_MANUFACTURING5_ENTRY,
Mpi2Manufacturing5Entry_t,
*pMpi2Manufacturing5Entry_t;
typedef struct _MPI2_CONFIG_PAGE_MAN_5 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 NumPhys; /*0x04 */
U8 Reserved1; /*0x05 */
U16 Reserved2; /*0x06 */
U32 Reserved3; /*0x08 */
U32 Reserved4; /*0x0C */
MPI2_MANUFACTURING5_ENTRY
Phy[MPI2_MAN_PAGE_5_PHY_ENTRIES];/*0x08 */
} MPI2_CONFIG_PAGE_MAN_5,
*PTR_MPI2_CONFIG_PAGE_MAN_5,
Mpi2ManufacturingPage5_t,
*pMpi2ManufacturingPage5_t;
#define MPI2_MANUFACTURING5_PAGEVERSION (0x03)
/*Manufacturing Page 6 */
typedef struct _MPI2_CONFIG_PAGE_MAN_6 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 ProductSpecificInfo;/*0x04 */
} MPI2_CONFIG_PAGE_MAN_6,
*PTR_MPI2_CONFIG_PAGE_MAN_6,
Mpi2ManufacturingPage6_t,
*pMpi2ManufacturingPage6_t;
#define MPI2_MANUFACTURING6_PAGEVERSION (0x00)
/*Manufacturing Page 7 */
typedef struct _MPI2_MANPAGE7_CONNECTOR_INFO {
U32 Pinout; /*0x00 */
U8 Connector[16]; /*0x04 */
U8 Location; /*0x14 */
U8 ReceptacleID; /*0x15 */
U16 Slot; /*0x16 */
U32 Reserved2; /*0x18 */
} MPI2_MANPAGE7_CONNECTOR_INFO,
*PTR_MPI2_MANPAGE7_CONNECTOR_INFO,
Mpi2ManPage7ConnectorInfo_t,
*pMpi2ManPage7ConnectorInfo_t;
/*defines for the Pinout field */
#define MPI2_MANPAGE7_PINOUT_LANE_MASK (0x0000FF00)
#define MPI2_MANPAGE7_PINOUT_LANE_SHIFT (8)
#define MPI2_MANPAGE7_PINOUT_TYPE_MASK (0x000000FF)
#define MPI2_MANPAGE7_PINOUT_TYPE_UNKNOWN (0x00)
#define MPI2_MANPAGE7_PINOUT_SATA_SINGLE (0x01)
#define MPI2_MANPAGE7_PINOUT_SFF_8482 (0x02)
#define MPI2_MANPAGE7_PINOUT_SFF_8486 (0x03)
#define MPI2_MANPAGE7_PINOUT_SFF_8484 (0x04)
#define MPI2_MANPAGE7_PINOUT_SFF_8087 (0x05)
#define MPI2_MANPAGE7_PINOUT_SFF_8643_4I (0x06)
#define MPI2_MANPAGE7_PINOUT_SFF_8643_8I (0x07)
#define MPI2_MANPAGE7_PINOUT_SFF_8470 (0x08)
#define MPI2_MANPAGE7_PINOUT_SFF_8088 (0x09)
#define MPI2_MANPAGE7_PINOUT_SFF_8644_4X (0x0A)
#define MPI2_MANPAGE7_PINOUT_SFF_8644_8X (0x0B)
#define MPI2_MANPAGE7_PINOUT_SFF_8644_16X (0x0C)
#define MPI2_MANPAGE7_PINOUT_SFF_8436 (0x0D)
/*defines for the Location field */
#define MPI2_MANPAGE7_LOCATION_UNKNOWN (0x01)
#define MPI2_MANPAGE7_LOCATION_INTERNAL (0x02)
#define MPI2_MANPAGE7_LOCATION_EXTERNAL (0x04)
#define MPI2_MANPAGE7_LOCATION_SWITCHABLE (0x08)
#define MPI2_MANPAGE7_LOCATION_AUTO (0x10)
#define MPI2_MANPAGE7_LOCATION_NOT_PRESENT (0x20)
#define MPI2_MANPAGE7_LOCATION_NOT_CONNECTED (0x80)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_MANPAGE7_CONNECTOR_INFO_MAX
#define MPI2_MANPAGE7_CONNECTOR_INFO_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_MAN_7 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Reserved2; /*0x08 */
U32 Flags; /*0x0C */
U8 EnclosureName[16]; /*0x10 */
U8 NumPhys; /*0x20 */
U8 Reserved3; /*0x21 */
U16 Reserved4; /*0x22 */
MPI2_MANPAGE7_CONNECTOR_INFO
ConnectorInfo[MPI2_MANPAGE7_CONNECTOR_INFO_MAX]; /*0x24 */
} MPI2_CONFIG_PAGE_MAN_7,
*PTR_MPI2_CONFIG_PAGE_MAN_7,
Mpi2ManufacturingPage7_t,
*pMpi2ManufacturingPage7_t;
#define MPI2_MANUFACTURING7_PAGEVERSION (0x01)
/*defines for the Flags field */
#define MPI2_MANPAGE7_FLAG_EVENTREPLAY_SLOT_ORDER (0x00000002)
#define MPI2_MANPAGE7_FLAG_USE_SLOT_INFO (0x00000001)
/*
*Generic structure to use for product-specific manufacturing pages
*(currently Manufacturing Page 8 through Manufacturing Page 31).
*/
typedef struct _MPI2_CONFIG_PAGE_MAN_PS {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 ProductSpecificInfo;/*0x04 */
} MPI2_CONFIG_PAGE_MAN_PS,
*PTR_MPI2_CONFIG_PAGE_MAN_PS,
Mpi2ManufacturingPagePS_t,
*pMpi2ManufacturingPagePS_t;
#define MPI2_MANUFACTURING8_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING9_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING10_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING11_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING12_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING13_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING14_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING15_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING16_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING17_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING18_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING19_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING20_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING21_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING22_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING23_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING24_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING25_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING26_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING27_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING28_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING29_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING30_PAGEVERSION (0x00)
#define MPI2_MANUFACTURING31_PAGEVERSION (0x00)
/****************************************************************************
* IO Unit Config Pages
****************************************************************************/
/*IO Unit Page 0 */
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_0 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U64 UniqueValue; /*0x04 */
MPI2_VERSION_UNION NvdataVersionDefault; /*0x08 */
MPI2_VERSION_UNION NvdataVersionPersistent; /*0x0A */
} MPI2_CONFIG_PAGE_IO_UNIT_0,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_0,
Mpi2IOUnitPage0_t, *pMpi2IOUnitPage0_t;
#define MPI2_IOUNITPAGE0_PAGEVERSION (0x02)
/*IO Unit Page 1 */
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Flags; /*0x04 */
} MPI2_CONFIG_PAGE_IO_UNIT_1,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_1,
Mpi2IOUnitPage1_t, *pMpi2IOUnitPage1_t;
#define MPI2_IOUNITPAGE1_PAGEVERSION (0x04)
/*IO Unit Page 1 Flags defines */
#define MPI25_IOUNITPAGE1_NEW_DEVICE_FAST_PATH_DISABLE (0x00002000)
#define MPI25_IOUNITPAGE1_DISABLE_FAST_PATH (0x00001000)
#define MPI2_IOUNITPAGE1_ENABLE_HOST_BASED_DISCOVERY (0x00000800)
#define MPI2_IOUNITPAGE1_MASK_SATA_WRITE_CACHE (0x00000600)
#define MPI2_IOUNITPAGE1_SATA_WRITE_CACHE_SHIFT (9)
#define MPI2_IOUNITPAGE1_ENABLE_SATA_WRITE_CACHE (0x00000000)
#define MPI2_IOUNITPAGE1_DISABLE_SATA_WRITE_CACHE (0x00000200)
#define MPI2_IOUNITPAGE1_UNCHANGED_SATA_WRITE_CACHE (0x00000400)
#define MPI2_IOUNITPAGE1_NATIVE_COMMAND_Q_DISABLE (0x00000100)
#define MPI2_IOUNITPAGE1_DISABLE_IR (0x00000040)
#define MPI2_IOUNITPAGE1_DISABLE_TASK_SET_FULL_HANDLING (0x00000020)
#define MPI2_IOUNITPAGE1_IR_USE_STATIC_VOLUME_ID (0x00000004)
/*IO Unit Page 3 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for GPIOCount at runtime.
*/
#ifndef MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX
#define MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_3 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 GPIOCount; /*0x04 */
U8 Reserved1; /*0x05 */
U16 Reserved2; /*0x06 */
U16
GPIOVal[MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX];/*0x08 */
} MPI2_CONFIG_PAGE_IO_UNIT_3,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_3,
Mpi2IOUnitPage3_t, *pMpi2IOUnitPage3_t;
#define MPI2_IOUNITPAGE3_PAGEVERSION (0x01)
/*defines for IO Unit Page 3 GPIOVal field */
#define MPI2_IOUNITPAGE3_GPIO_FUNCTION_MASK (0xFFFC)
#define MPI2_IOUNITPAGE3_GPIO_FUNCTION_SHIFT (2)
#define MPI2_IOUNITPAGE3_GPIO_SETTING_OFF (0x0000)
#define MPI2_IOUNITPAGE3_GPIO_SETTING_ON (0x0001)
/*IO Unit Page 5 */
/*
*Upper layer code (drivers, utilities, etc.) should leave this define set to
*one and check the value returned for NumDmaEngines at runtime.
*/
#ifndef MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES
#define MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_5 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U64
RaidAcceleratorBufferBaseAddress; /*0x04 */
U64
RaidAcceleratorBufferSize; /*0x0C */
U64
RaidAcceleratorControlBaseAddress; /*0x14 */
U8 RAControlSize; /*0x1C */
U8 NumDmaEngines; /*0x1D */
U8 RAMinControlSize; /*0x1E */
U8 RAMaxControlSize; /*0x1F */
U32 Reserved1; /*0x20 */
U32 Reserved2; /*0x24 */
U32 Reserved3; /*0x28 */
U32
DmaEngineCapabilities[MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES]; /*0x2C */
} MPI2_CONFIG_PAGE_IO_UNIT_5,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_5,
Mpi2IOUnitPage5_t, *pMpi2IOUnitPage5_t;
#define MPI2_IOUNITPAGE5_PAGEVERSION (0x00)
/*defines for IO Unit Page 5 DmaEngineCapabilities field */
#define MPI2_IOUNITPAGE5_DMA_CAP_MASK_MAX_REQUESTS (0xFF00)
#define MPI2_IOUNITPAGE5_DMA_CAP_SHIFT_MAX_REQUESTS (16)
#define MPI2_IOUNITPAGE5_DMA_CAP_EEDP (0x0008)
#define MPI2_IOUNITPAGE5_DMA_CAP_PARITY_GENERATION (0x0004)
#define MPI2_IOUNITPAGE5_DMA_CAP_HASHING (0x0002)
#define MPI2_IOUNITPAGE5_DMA_CAP_ENCRYPTION (0x0001)
/*IO Unit Page 6 */
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_6 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U16 Flags; /*0x04 */
U8 RAHostControlSize; /*0x06 */
U8 Reserved0; /*0x07 */
U64
RaidAcceleratorHostControlBaseAddress; /*0x08 */
U32 Reserved1; /*0x10 */
U32 Reserved2; /*0x14 */
U32 Reserved3; /*0x18 */
} MPI2_CONFIG_PAGE_IO_UNIT_6,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_6,
Mpi2IOUnitPage6_t, *pMpi2IOUnitPage6_t;
#define MPI2_IOUNITPAGE6_PAGEVERSION (0x00)
/*defines for IO Unit Page 6 Flags field */
#define MPI2_IOUNITPAGE6_FLAGS_ENABLE_RAID_ACCELERATOR (0x0001)
/*IO Unit Page 7 */
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_7 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 CurrentPowerMode; /*0x04 */
U8 PreviousPowerMode; /*0x05 */
U8 PCIeWidth; /*0x06 */
U8 PCIeSpeed; /*0x07 */
U32 ProcessorState; /*0x08 */
U32
PowerManagementCapabilities; /*0x0C */
U16 IOCTemperature; /*0x10 */
U8
IOCTemperatureUnits; /*0x12 */
U8 IOCSpeed; /*0x13 */
U16 BoardTemperature; /*0x14 */
U8
BoardTemperatureUnits; /*0x16 */
U8 Reserved3; /*0x17 */
} MPI2_CONFIG_PAGE_IO_UNIT_7,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_7,
Mpi2IOUnitPage7_t, *pMpi2IOUnitPage7_t;
#define MPI2_IOUNITPAGE7_PAGEVERSION (0x02)
/*defines for IO Unit Page 7 CurrentPowerMode and PreviousPowerMode fields */
#define MPI25_IOUNITPAGE7_PM_INIT_MASK (0xC0)
#define MPI25_IOUNITPAGE7_PM_INIT_UNAVAILABLE (0x00)
#define MPI25_IOUNITPAGE7_PM_INIT_HOST (0x40)
#define MPI25_IOUNITPAGE7_PM_INIT_IO_UNIT (0x80)
#define MPI25_IOUNITPAGE7_PM_INIT_PCIE_DPA (0xC0)
#define MPI25_IOUNITPAGE7_PM_MODE_MASK (0x07)
#define MPI25_IOUNITPAGE7_PM_MODE_UNAVAILABLE (0x00)
#define MPI25_IOUNITPAGE7_PM_MODE_UNKNOWN (0x01)
#define MPI25_IOUNITPAGE7_PM_MODE_FULL_POWER (0x04)
#define MPI25_IOUNITPAGE7_PM_MODE_REDUCED_POWER (0x05)
#define MPI25_IOUNITPAGE7_PM_MODE_STANDBY (0x06)
/*defines for IO Unit Page 7 PCIeWidth field */
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X1 (0x01)
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X2 (0x02)
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X4 (0x04)
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X8 (0x08)
/*defines for IO Unit Page 7 PCIeSpeed field */
#define MPI2_IOUNITPAGE7_PCIE_SPEED_2_5_GBPS (0x00)
#define MPI2_IOUNITPAGE7_PCIE_SPEED_5_0_GBPS (0x01)
#define MPI2_IOUNITPAGE7_PCIE_SPEED_8_0_GBPS (0x02)
/*defines for IO Unit Page 7 ProcessorState field */
#define MPI2_IOUNITPAGE7_PSTATE_MASK_SECOND (0x0000000F)
#define MPI2_IOUNITPAGE7_PSTATE_SHIFT_SECOND (0)
#define MPI2_IOUNITPAGE7_PSTATE_NOT_PRESENT (0x00)
#define MPI2_IOUNITPAGE7_PSTATE_DISABLED (0x01)
#define MPI2_IOUNITPAGE7_PSTATE_ENABLED (0x02)
/*defines for IO Unit Page 7 PowerManagementCapabilities field */
#define MPI25_IOUNITPAGE7_PMCAP_DPA_FULL_PWR_MODE (0x00400000)
#define MPI25_IOUNITPAGE7_PMCAP_DPA_REDUCED_PWR_MODE (0x00200000)
#define MPI25_IOUNITPAGE7_PMCAP_DPA_STANDBY_MODE (0x00100000)
#define MPI25_IOUNITPAGE7_PMCAP_HOST_FULL_PWR_MODE (0x00040000)
#define MPI25_IOUNITPAGE7_PMCAP_HOST_REDUCED_PWR_MODE (0x00020000)
#define MPI25_IOUNITPAGE7_PMCAP_HOST_STANDBY_MODE (0x00010000)
#define MPI25_IOUNITPAGE7_PMCAP_IO_FULL_PWR_MODE (0x00004000)
#define MPI25_IOUNITPAGE7_PMCAP_IO_REDUCED_PWR_MODE (0x00002000)
#define MPI25_IOUNITPAGE7_PMCAP_IO_STANDBY_MODE (0x00001000)
#define MPI2_IOUNITPAGE7_PMCAP_HOST_12_5_PCT_IOCSPEED (0x00000400)
#define MPI2_IOUNITPAGE7_PMCAP_HOST_25_0_PCT_IOCSPEED (0x00000200)
#define MPI2_IOUNITPAGE7_PMCAP_HOST_50_0_PCT_IOCSPEED (0x00000100)
#define MPI25_IOUNITPAGE7_PMCAP_IO_12_5_PCT_IOCSPEED (0x00000040)
#define MPI25_IOUNITPAGE7_PMCAP_IO_25_0_PCT_IOCSPEED (0x00000020)
#define MPI25_IOUNITPAGE7_PMCAP_IO_50_0_PCT_IOCSPEED (0x00000010)
#define MPI2_IOUNITPAGE7_PMCAP_HOST_WIDTH_CHANGE_PCIE (0x00000008)
#define MPI2_IOUNITPAGE7_PMCAP_HOST_SPEED_CHANGE_PCIE (0x00000004)
#define MPI25_IOUNITPAGE7_PMCAP_IO_WIDTH_CHANGE_PCIE (0x00000002)
#define MPI25_IOUNITPAGE7_PMCAP_IO_SPEED_CHANGE_PCIE (0x00000001)
/*obsolete names for the PowerManagementCapabilities bits (above) */
#define MPI2_IOUNITPAGE7_PMCAP_12_5_PCT_IOCSPEED (0x00000400)
#define MPI2_IOUNITPAGE7_PMCAP_25_0_PCT_IOCSPEED (0x00000200)
#define MPI2_IOUNITPAGE7_PMCAP_50_0_PCT_IOCSPEED (0x00000100)
#define MPI2_IOUNITPAGE7_PMCAP_PCIE_WIDTH_CHANGE (0x00000008) /*obsolete */
#define MPI2_IOUNITPAGE7_PMCAP_PCIE_SPEED_CHANGE (0x00000004) /*obsolete */
/*defines for IO Unit Page 7 IOCTemperatureUnits field */
#define MPI2_IOUNITPAGE7_IOC_TEMP_NOT_PRESENT (0x00)
#define MPI2_IOUNITPAGE7_IOC_TEMP_FAHRENHEIT (0x01)
#define MPI2_IOUNITPAGE7_IOC_TEMP_CELSIUS (0x02)
/*defines for IO Unit Page 7 IOCSpeed field */
#define MPI2_IOUNITPAGE7_IOC_SPEED_FULL (0x01)
#define MPI2_IOUNITPAGE7_IOC_SPEED_HALF (0x02)
#define MPI2_IOUNITPAGE7_IOC_SPEED_QUARTER (0x04)
#define MPI2_IOUNITPAGE7_IOC_SPEED_EIGHTH (0x08)
/*defines for IO Unit Page 7 BoardTemperatureUnits field */
#define MPI2_IOUNITPAGE7_BOARD_TEMP_NOT_PRESENT (0x00)
#define MPI2_IOUNITPAGE7_BOARD_TEMP_FAHRENHEIT (0x01)
#define MPI2_IOUNITPAGE7_BOARD_TEMP_CELSIUS (0x02)
/*IO Unit Page 8 */
#define MPI2_IOUNIT8_NUM_THRESHOLDS (4)
typedef struct _MPI2_IOUNIT8_SENSOR {
U16 Flags; /*0x00 */
U16 Reserved1; /*0x02 */
U16
Threshold[MPI2_IOUNIT8_NUM_THRESHOLDS]; /*0x04 */
U32 Reserved2; /*0x0C */
U32 Reserved3; /*0x10 */
U32 Reserved4; /*0x14 */
} MPI2_IOUNIT8_SENSOR, *PTR_MPI2_IOUNIT8_SENSOR,
Mpi2IOUnit8Sensor_t, *pMpi2IOUnit8Sensor_t;
/*defines for IO Unit Page 8 Sensor Flags field */
#define MPI2_IOUNIT8_SENSOR_FLAGS_T3_ENABLE (0x0008)
#define MPI2_IOUNIT8_SENSOR_FLAGS_T2_ENABLE (0x0004)
#define MPI2_IOUNIT8_SENSOR_FLAGS_T1_ENABLE (0x0002)
#define MPI2_IOUNIT8_SENSOR_FLAGS_T0_ENABLE (0x0001)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumSensors at runtime.
*/
#ifndef MPI2_IOUNITPAGE8_SENSOR_ENTRIES
#define MPI2_IOUNITPAGE8_SENSOR_ENTRIES (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_8 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Reserved2; /*0x08 */
U8 NumSensors; /*0x0C */
U8 PollingInterval; /*0x0D */
U16 Reserved3; /*0x0E */
MPI2_IOUNIT8_SENSOR
Sensor[MPI2_IOUNITPAGE8_SENSOR_ENTRIES];/*0x10 */
} MPI2_CONFIG_PAGE_IO_UNIT_8,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_8,
Mpi2IOUnitPage8_t, *pMpi2IOUnitPage8_t;
#define MPI2_IOUNITPAGE8_PAGEVERSION (0x00)
/*IO Unit Page 9 */
typedef struct _MPI2_IOUNIT9_SENSOR {
U16 CurrentTemperature; /*0x00 */
U16 Reserved1; /*0x02 */
U8 Flags; /*0x04 */
U8 Reserved2; /*0x05 */
U16 Reserved3; /*0x06 */
U32 Reserved4; /*0x08 */
U32 Reserved5; /*0x0C */
} MPI2_IOUNIT9_SENSOR, *PTR_MPI2_IOUNIT9_SENSOR,
Mpi2IOUnit9Sensor_t, *pMpi2IOUnit9Sensor_t;
/*defines for IO Unit Page 9 Sensor Flags field */
#define MPI2_IOUNIT9_SENSOR_FLAGS_TEMP_VALID (0x01)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumSensors at runtime.
*/
#ifndef MPI2_IOUNITPAGE9_SENSOR_ENTRIES
#define MPI2_IOUNITPAGE9_SENSOR_ENTRIES (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_9 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Reserved2; /*0x08 */
U8 NumSensors; /*0x0C */
U8 Reserved4; /*0x0D */
U16 Reserved3; /*0x0E */
MPI2_IOUNIT9_SENSOR
Sensor[MPI2_IOUNITPAGE9_SENSOR_ENTRIES];/*0x10 */
} MPI2_CONFIG_PAGE_IO_UNIT_9,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_9,
Mpi2IOUnitPage9_t, *pMpi2IOUnitPage9_t;
#define MPI2_IOUNITPAGE9_PAGEVERSION (0x00)
/*IO Unit Page 10 */
typedef struct _MPI2_IOUNIT10_FUNCTION {
U8 CreditPercent; /*0x00 */
U8 Reserved1; /*0x01 */
U16 Reserved2; /*0x02 */
} MPI2_IOUNIT10_FUNCTION,
*PTR_MPI2_IOUNIT10_FUNCTION,
Mpi2IOUnit10Function_t,
*pMpi2IOUnit10Function_t;
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumFunctions at runtime.
*/
#ifndef MPI2_IOUNITPAGE10_FUNCTION_ENTRIES
#define MPI2_IOUNITPAGE10_FUNCTION_ENTRIES (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_10 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 NumFunctions; /*0x04 */
U8 Reserved1; /*0x05 */
U16 Reserved2; /*0x06 */
U32 Reserved3; /*0x08 */
U32 Reserved4; /*0x0C */
MPI2_IOUNIT10_FUNCTION
Function[MPI2_IOUNITPAGE10_FUNCTION_ENTRIES];/*0x10 */
} MPI2_CONFIG_PAGE_IO_UNIT_10,
*PTR_MPI2_CONFIG_PAGE_IO_UNIT_10,
Mpi2IOUnitPage10_t, *pMpi2IOUnitPage10_t;
#define MPI2_IOUNITPAGE10_PAGEVERSION (0x01)
/****************************************************************************
* IOC Config Pages
****************************************************************************/
/*IOC Page 0 */
typedef struct _MPI2_CONFIG_PAGE_IOC_0 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Reserved2; /*0x08 */
U16 VendorID; /*0x0C */
U16 DeviceID; /*0x0E */
U8 RevisionID; /*0x10 */
U8 Reserved3; /*0x11 */
U16 Reserved4; /*0x12 */
U32 ClassCode; /*0x14 */
U16 SubsystemVendorID; /*0x18 */
U16 SubsystemID; /*0x1A */
} MPI2_CONFIG_PAGE_IOC_0,
*PTR_MPI2_CONFIG_PAGE_IOC_0,
Mpi2IOCPage0_t, *pMpi2IOCPage0_t;
#define MPI2_IOCPAGE0_PAGEVERSION (0x02)
/*IOC Page 1 */
typedef struct _MPI2_CONFIG_PAGE_IOC_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Flags; /*0x04 */
U32 CoalescingTimeout; /*0x08 */
U8 CoalescingDepth; /*0x0C */
U8 PCISlotNum; /*0x0D */
U8 PCIBusNum; /*0x0E */
U8 PCIDomainSegment; /*0x0F */
U32 Reserved1; /*0x10 */
U32 Reserved2; /*0x14 */
} MPI2_CONFIG_PAGE_IOC_1,
*PTR_MPI2_CONFIG_PAGE_IOC_1,
Mpi2IOCPage1_t, *pMpi2IOCPage1_t;
#define MPI2_IOCPAGE1_PAGEVERSION (0x05)
/*defines for IOC Page 1 Flags field */
#define MPI2_IOCPAGE1_REPLY_COALESCING (0x00000001)
#define MPI2_IOCPAGE1_PCISLOTNUM_UNKNOWN (0xFF)
#define MPI2_IOCPAGE1_PCIBUSNUM_UNKNOWN (0xFF)
#define MPI2_IOCPAGE1_PCIDOMAIN_UNKNOWN (0xFF)
/*IOC Page 6 */
typedef struct _MPI2_CONFIG_PAGE_IOC_6 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32
CapabilitiesFlags; /*0x04 */
U8 MaxDrivesRAID0; /*0x08 */
U8 MaxDrivesRAID1; /*0x09 */
U8
MaxDrivesRAID1E; /*0x0A */
U8
MaxDrivesRAID10; /*0x0B */
U8 MinDrivesRAID0; /*0x0C */
U8 MinDrivesRAID1; /*0x0D */
U8
MinDrivesRAID1E; /*0x0E */
U8
MinDrivesRAID10; /*0x0F */
U32 Reserved1; /*0x10 */
U8
MaxGlobalHotSpares; /*0x14 */
U8 MaxPhysDisks; /*0x15 */
U8 MaxVolumes; /*0x16 */
U8 MaxConfigs; /*0x17 */
U8 MaxOCEDisks; /*0x18 */
U8 Reserved2; /*0x19 */
U16 Reserved3; /*0x1A */
U32
SupportedStripeSizeMapRAID0; /*0x1C */
U32
SupportedStripeSizeMapRAID1E; /*0x20 */
U32
SupportedStripeSizeMapRAID10; /*0x24 */
U32 Reserved4; /*0x28 */
U32 Reserved5; /*0x2C */
U16
DefaultMetadataSize; /*0x30 */
U16 Reserved6; /*0x32 */
U16
MaxBadBlockTableEntries; /*0x34 */
U16 Reserved7; /*0x36 */
U32
IRNvsramVersion; /*0x38 */
} MPI2_CONFIG_PAGE_IOC_6,
*PTR_MPI2_CONFIG_PAGE_IOC_6,
Mpi2IOCPage6_t, *pMpi2IOCPage6_t;
#define MPI2_IOCPAGE6_PAGEVERSION (0x05)
/*defines for IOC Page 6 CapabilitiesFlags */
#define MPI2_IOCPAGE6_CAP_FLAGS_4K_SECTORS_SUPPORT (0x00000020)
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID10_SUPPORT (0x00000010)
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID1_SUPPORT (0x00000008)
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID1E_SUPPORT (0x00000004)
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID0_SUPPORT (0x00000002)
#define MPI2_IOCPAGE6_CAP_FLAGS_GLOBAL_HOT_SPARE (0x00000001)
/*IOC Page 7 */
#define MPI2_IOCPAGE7_EVENTMASK_WORDS (4)
typedef struct _MPI2_CONFIG_PAGE_IOC_7 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32
EventMasks[MPI2_IOCPAGE7_EVENTMASK_WORDS];/*0x08 */
U16 SASBroadcastPrimitiveMasks; /*0x18 */
U16 SASNotifyPrimitiveMasks; /*0x1A */
U32 Reserved3; /*0x1C */
} MPI2_CONFIG_PAGE_IOC_7,
*PTR_MPI2_CONFIG_PAGE_IOC_7,
Mpi2IOCPage7_t, *pMpi2IOCPage7_t;
#define MPI2_IOCPAGE7_PAGEVERSION (0x02)
/*IOC Page 8 */
typedef struct _MPI2_CONFIG_PAGE_IOC_8 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 NumDevsPerEnclosure; /*0x04 */
U8 Reserved1; /*0x05 */
U16 Reserved2; /*0x06 */
U16 MaxPersistentEntries; /*0x08 */
U16 MaxNumPhysicalMappedIDs; /*0x0A */
U16 Flags; /*0x0C */
U16 Reserved3; /*0x0E */
U16 IRVolumeMappingFlags; /*0x10 */
U16 Reserved4; /*0x12 */
U32 Reserved5; /*0x14 */
} MPI2_CONFIG_PAGE_IOC_8,
*PTR_MPI2_CONFIG_PAGE_IOC_8,
Mpi2IOCPage8_t, *pMpi2IOCPage8_t;
#define MPI2_IOCPAGE8_PAGEVERSION (0x00)
/*defines for IOC Page 8 Flags field */
#define MPI2_IOCPAGE8_FLAGS_DA_START_SLOT_1 (0x00000020)
#define MPI2_IOCPAGE8_FLAGS_RESERVED_TARGETID_0 (0x00000010)
#define MPI2_IOCPAGE8_FLAGS_MASK_MAPPING_MODE (0x0000000E)
#define MPI2_IOCPAGE8_FLAGS_DEVICE_PERSISTENCE_MAPPING (0x00000000)
#define MPI2_IOCPAGE8_FLAGS_ENCLOSURE_SLOT_MAPPING (0x00000002)
#define MPI2_IOCPAGE8_FLAGS_DISABLE_PERSISTENT_MAPPING (0x00000001)
#define MPI2_IOCPAGE8_FLAGS_ENABLE_PERSISTENT_MAPPING (0x00000000)
/*defines for IOC Page 8 IRVolumeMappingFlags */
#define MPI2_IOCPAGE8_IRFLAGS_MASK_VOLUME_MAPPING_MODE (0x00000003)
#define MPI2_IOCPAGE8_IRFLAGS_LOW_VOLUME_MAPPING (0x00000000)
#define MPI2_IOCPAGE8_IRFLAGS_HIGH_VOLUME_MAPPING (0x00000001)
/****************************************************************************
* BIOS Config Pages
****************************************************************************/
/*BIOS Page 1 */
typedef struct _MPI2_CONFIG_PAGE_BIOS_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 BiosOptions; /*0x04 */
U32 IOCSettings; /*0x08 */
U32 Reserved1; /*0x0C */
U32 DeviceSettings; /*0x10 */
U16 NumberOfDevices; /*0x14 */
U16 UEFIVersion; /*0x16 */
U16 IOTimeoutBlockDevicesNonRM; /*0x18 */
U16 IOTimeoutSequential; /*0x1A */
U16 IOTimeoutOther; /*0x1C */
U16 IOTimeoutBlockDevicesRM; /*0x1E */
} MPI2_CONFIG_PAGE_BIOS_1,
*PTR_MPI2_CONFIG_PAGE_BIOS_1,
Mpi2BiosPage1_t, *pMpi2BiosPage1_t;
#define MPI2_BIOSPAGE1_PAGEVERSION (0x05)
/*values for BIOS Page 1 BiosOptions field */
#define MPI2_BIOSPAGE1_OPTIONS_MASK_OEM_ID (0x000000F0)
#define MPI2_BIOSPAGE1_OPTIONS_LSI_OEM_ID (0x00000000)
#define MPI2_BIOSPAGE1_OPTIONS_MASK_UEFI_HII_REGISTRATION (0x00000006)
#define MPI2_BIOSPAGE1_OPTIONS_ENABLE_UEFI_HII (0x00000000)
#define MPI2_BIOSPAGE1_OPTIONS_DISABLE_UEFI_HII (0x00000002)
#define MPI2_BIOSPAGE1_OPTIONS_VERSION_CHECK_UEFI_HII (0x00000004)
#define MPI2_BIOSPAGE1_OPTIONS_DISABLE_BIOS (0x00000001)
/*values for BIOS Page 1 IOCSettings field */
#define MPI2_BIOSPAGE1_IOCSET_MASK_BOOT_PREFERENCE (0x00030000)
#define MPI2_BIOSPAGE1_IOCSET_ENCLOSURE_SLOT_BOOT (0x00000000)
#define MPI2_BIOSPAGE1_IOCSET_SAS_ADDRESS_BOOT (0x00010000)
#define MPI2_BIOSPAGE1_IOCSET_MASK_RM_SETTING (0x000000C0)
#define MPI2_BIOSPAGE1_IOCSET_NONE_RM_SETTING (0x00000000)
#define MPI2_BIOSPAGE1_IOCSET_BOOT_RM_SETTING (0x00000040)
#define MPI2_BIOSPAGE1_IOCSET_MEDIA_RM_SETTING (0x00000080)
#define MPI2_BIOSPAGE1_IOCSET_MASK_ADAPTER_SUPPORT (0x00000030)
#define MPI2_BIOSPAGE1_IOCSET_NO_SUPPORT (0x00000000)
#define MPI2_BIOSPAGE1_IOCSET_BIOS_SUPPORT (0x00000010)
#define MPI2_BIOSPAGE1_IOCSET_OS_SUPPORT (0x00000020)
#define MPI2_BIOSPAGE1_IOCSET_ALL_SUPPORT (0x00000030)
#define MPI2_BIOSPAGE1_IOCSET_ALTERNATE_CHS (0x00000008)
/*values for BIOS Page 1 DeviceSettings field */
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_SMART_POLLING (0x00000010)
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_SEQ_LUN (0x00000008)
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_RM_LUN (0x00000004)
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_NON_RM_LUN (0x00000002)
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_OTHER_LUN (0x00000001)
/*defines for BIOS Page 1 UEFIVersion field */
#define MPI2_BIOSPAGE1_UEFI_VER_MAJOR_MASK (0xFF00)
#define MPI2_BIOSPAGE1_UEFI_VER_MAJOR_SHIFT (8)
#define MPI2_BIOSPAGE1_UEFI_VER_MINOR_MASK (0x00FF)
#define MPI2_BIOSPAGE1_UEFI_VER_MINOR_SHIFT (0)
/*BIOS Page 2 */
typedef struct _MPI2_BOOT_DEVICE_ADAPTER_ORDER {
U32 Reserved1; /*0x00 */
U32 Reserved2; /*0x04 */
U32 Reserved3; /*0x08 */
U32 Reserved4; /*0x0C */
U32 Reserved5; /*0x10 */
U32 Reserved6; /*0x14 */
} MPI2_BOOT_DEVICE_ADAPTER_ORDER,
*PTR_MPI2_BOOT_DEVICE_ADAPTER_ORDER,
Mpi2BootDeviceAdapterOrder_t,
*pMpi2BootDeviceAdapterOrder_t;
typedef struct _MPI2_BOOT_DEVICE_SAS_WWID {
U64 SASAddress; /*0x00 */
U8 LUN[8]; /*0x08 */
U32 Reserved1; /*0x10 */
U32 Reserved2; /*0x14 */
} MPI2_BOOT_DEVICE_SAS_WWID,
*PTR_MPI2_BOOT_DEVICE_SAS_WWID,
Mpi2BootDeviceSasWwid_t,
*pMpi2BootDeviceSasWwid_t;
typedef struct _MPI2_BOOT_DEVICE_ENCLOSURE_SLOT {
U64 EnclosureLogicalID; /*0x00 */
U32 Reserved1; /*0x08 */
U32 Reserved2; /*0x0C */
U16 SlotNumber; /*0x10 */
U16 Reserved3; /*0x12 */
U32 Reserved4; /*0x14 */
} MPI2_BOOT_DEVICE_ENCLOSURE_SLOT,
*PTR_MPI2_BOOT_DEVICE_ENCLOSURE_SLOT,
Mpi2BootDeviceEnclosureSlot_t,
*pMpi2BootDeviceEnclosureSlot_t;
typedef struct _MPI2_BOOT_DEVICE_DEVICE_NAME {
U64 DeviceName; /*0x00 */
U8 LUN[8]; /*0x08 */
U32 Reserved1; /*0x10 */
U32 Reserved2; /*0x14 */
} MPI2_BOOT_DEVICE_DEVICE_NAME,
*PTR_MPI2_BOOT_DEVICE_DEVICE_NAME,
Mpi2BootDeviceDeviceName_t,
*pMpi2BootDeviceDeviceName_t;
typedef union _MPI2_MPI2_BIOSPAGE2_BOOT_DEVICE {
MPI2_BOOT_DEVICE_ADAPTER_ORDER AdapterOrder;
MPI2_BOOT_DEVICE_SAS_WWID SasWwid;
MPI2_BOOT_DEVICE_ENCLOSURE_SLOT EnclosureSlot;
MPI2_BOOT_DEVICE_DEVICE_NAME DeviceName;
} MPI2_BIOSPAGE2_BOOT_DEVICE,
*PTR_MPI2_BIOSPAGE2_BOOT_DEVICE,
Mpi2BiosPage2BootDevice_t,
*pMpi2BiosPage2BootDevice_t;
typedef struct _MPI2_CONFIG_PAGE_BIOS_2 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x04 */
U32 Reserved2; /*0x08 */
U32 Reserved3; /*0x0C */
U32 Reserved4; /*0x10 */
U32 Reserved5; /*0x14 */
U32 Reserved6; /*0x18 */
U8 ReqBootDeviceForm; /*0x1C */
U8 Reserved7; /*0x1D */
U16 Reserved8; /*0x1E */
MPI2_BIOSPAGE2_BOOT_DEVICE RequestedBootDevice; /*0x20 */
U8 ReqAltBootDeviceForm; /*0x38 */
U8 Reserved9; /*0x39 */
U16 Reserved10; /*0x3A */
MPI2_BIOSPAGE2_BOOT_DEVICE RequestedAltBootDevice; /*0x3C */
U8 CurrentBootDeviceForm; /*0x58 */
U8 Reserved11; /*0x59 */
U16 Reserved12; /*0x5A */
MPI2_BIOSPAGE2_BOOT_DEVICE CurrentBootDevice; /*0x58 */
} MPI2_CONFIG_PAGE_BIOS_2, *PTR_MPI2_CONFIG_PAGE_BIOS_2,
Mpi2BiosPage2_t, *pMpi2BiosPage2_t;
#define MPI2_BIOSPAGE2_PAGEVERSION (0x04)
/*values for BIOS Page 2 BootDeviceForm fields */
#define MPI2_BIOSPAGE2_FORM_MASK (0x0F)
#define MPI2_BIOSPAGE2_FORM_NO_DEVICE_SPECIFIED (0x00)
#define MPI2_BIOSPAGE2_FORM_SAS_WWID (0x05)
#define MPI2_BIOSPAGE2_FORM_ENCLOSURE_SLOT (0x06)
#define MPI2_BIOSPAGE2_FORM_DEVICE_NAME (0x07)
/*BIOS Page 3 */
typedef struct _MPI2_ADAPTER_INFO {
U8 PciBusNumber; /*0x00 */
U8 PciDeviceAndFunctionNumber; /*0x01 */
U16 AdapterFlags; /*0x02 */
} MPI2_ADAPTER_INFO, *PTR_MPI2_ADAPTER_INFO,
Mpi2AdapterInfo_t, *pMpi2AdapterInfo_t;
#define MPI2_ADAPTER_INFO_FLAGS_EMBEDDED (0x0001)
#define MPI2_ADAPTER_INFO_FLAGS_INIT_STATUS (0x0002)
typedef struct _MPI2_CONFIG_PAGE_BIOS_3 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U32 GlobalFlags; /*0x04 */
U32 BiosVersion; /*0x08 */
MPI2_ADAPTER_INFO AdapterOrder[4]; /*0x0C */
U32 Reserved1; /*0x1C */
} MPI2_CONFIG_PAGE_BIOS_3,
*PTR_MPI2_CONFIG_PAGE_BIOS_3,
Mpi2BiosPage3_t, *pMpi2BiosPage3_t;
#define MPI2_BIOSPAGE3_PAGEVERSION (0x00)
/*values for BIOS Page 3 GlobalFlags */
#define MPI2_BIOSPAGE3_FLAGS_PAUSE_ON_ERROR (0x00000002)
#define MPI2_BIOSPAGE3_FLAGS_VERBOSE_ENABLE (0x00000004)
#define MPI2_BIOSPAGE3_FLAGS_HOOK_INT_40_DISABLE (0x00000010)
#define MPI2_BIOSPAGE3_FLAGS_DEV_LIST_DISPLAY_MASK (0x000000E0)
#define MPI2_BIOSPAGE3_FLAGS_INSTALLED_DEV_DISPLAY (0x00000000)
#define MPI2_BIOSPAGE3_FLAGS_ADAPTER_DISPLAY (0x00000020)
#define MPI2_BIOSPAGE3_FLAGS_ADAPTER_DEV_DISPLAY (0x00000040)
/*BIOS Page 4 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_BIOS_PAGE_4_PHY_ENTRIES
#define MPI2_BIOS_PAGE_4_PHY_ENTRIES (1)
#endif
typedef struct _MPI2_BIOS4_ENTRY {
U64 ReassignmentWWID; /*0x00 */
U64 ReassignmentDeviceName; /*0x08 */
} MPI2_BIOS4_ENTRY, *PTR_MPI2_BIOS4_ENTRY,
Mpi2MBios4Entry_t, *pMpi2Bios4Entry_t;
typedef struct _MPI2_CONFIG_PAGE_BIOS_4 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 NumPhys; /*0x04 */
U8 Reserved1; /*0x05 */
U16 Reserved2; /*0x06 */
MPI2_BIOS4_ENTRY
Phy[MPI2_BIOS_PAGE_4_PHY_ENTRIES]; /*0x08 */
} MPI2_CONFIG_PAGE_BIOS_4, *PTR_MPI2_CONFIG_PAGE_BIOS_4,
Mpi2BiosPage4_t, *pMpi2BiosPage4_t;
#define MPI2_BIOSPAGE4_PAGEVERSION (0x01)
/****************************************************************************
* RAID Volume Config Pages
****************************************************************************/
/*RAID Volume Page 0 */
typedef struct _MPI2_RAIDVOL0_PHYS_DISK {
U8 RAIDSetNum; /*0x00 */
U8 PhysDiskMap; /*0x01 */
U8 PhysDiskNum; /*0x02 */
U8 Reserved; /*0x03 */
} MPI2_RAIDVOL0_PHYS_DISK, *PTR_MPI2_RAIDVOL0_PHYS_DISK,
Mpi2RaidVol0PhysDisk_t, *pMpi2RaidVol0PhysDisk_t;
/*defines for the PhysDiskMap field */
#define MPI2_RAIDVOL0_PHYSDISK_PRIMARY (0x01)
#define MPI2_RAIDVOL0_PHYSDISK_SECONDARY (0x02)
typedef struct _MPI2_RAIDVOL0_SETTINGS {
U16 Settings; /*0x00 */
U8 HotSparePool; /*0x01 */
U8 Reserved; /*0x02 */
} MPI2_RAIDVOL0_SETTINGS, *PTR_MPI2_RAIDVOL0_SETTINGS,
Mpi2RaidVol0Settings_t,
*pMpi2RaidVol0Settings_t;
/*RAID Volume Page 0 HotSparePool defines, also used in RAID Physical Disk */
#define MPI2_RAID_HOT_SPARE_POOL_0 (0x01)
#define MPI2_RAID_HOT_SPARE_POOL_1 (0x02)
#define MPI2_RAID_HOT_SPARE_POOL_2 (0x04)
#define MPI2_RAID_HOT_SPARE_POOL_3 (0x08)
#define MPI2_RAID_HOT_SPARE_POOL_4 (0x10)
#define MPI2_RAID_HOT_SPARE_POOL_5 (0x20)
#define MPI2_RAID_HOT_SPARE_POOL_6 (0x40)
#define MPI2_RAID_HOT_SPARE_POOL_7 (0x80)
/*RAID Volume Page 0 VolumeSettings defines */
#define MPI2_RAIDVOL0_SETTING_USE_PRODUCT_ID_SUFFIX (0x0008)
#define MPI2_RAIDVOL0_SETTING_AUTO_CONFIG_HSWAP_DISABLE (0x0004)
#define MPI2_RAIDVOL0_SETTING_MASK_WRITE_CACHING (0x0003)
#define MPI2_RAIDVOL0_SETTING_UNCHANGED (0x0000)
#define MPI2_RAIDVOL0_SETTING_DISABLE_WRITE_CACHING (0x0001)
#define MPI2_RAIDVOL0_SETTING_ENABLE_WRITE_CACHING (0x0002)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhysDisks at runtime.
*/
#ifndef MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX
#define MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_RAID_VOL_0 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U16 DevHandle; /*0x04 */
U8 VolumeState; /*0x06 */
U8 VolumeType; /*0x07 */
U32 VolumeStatusFlags; /*0x08 */
MPI2_RAIDVOL0_SETTINGS VolumeSettings; /*0x0C */
U64 MaxLBA; /*0x10 */
U32 StripeSize; /*0x18 */
U16 BlockSize; /*0x1C */
U16 Reserved1; /*0x1E */
U8 SupportedPhysDisks;/*0x20 */
U8 ResyncRate; /*0x21 */
U16 DataScrubDuration; /*0x22 */
U8 NumPhysDisks; /*0x24 */
U8 Reserved2; /*0x25 */
U8 Reserved3; /*0x26 */
U8 InactiveStatus; /*0x27 */
MPI2_RAIDVOL0_PHYS_DISK
PhysDisk[MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX]; /*0x28 */
} MPI2_CONFIG_PAGE_RAID_VOL_0,
*PTR_MPI2_CONFIG_PAGE_RAID_VOL_0,
Mpi2RaidVolPage0_t, *pMpi2RaidVolPage0_t;
#define MPI2_RAIDVOLPAGE0_PAGEVERSION (0x0A)
/*values for RAID VolumeState */
#define MPI2_RAID_VOL_STATE_MISSING (0x00)
#define MPI2_RAID_VOL_STATE_FAILED (0x01)
#define MPI2_RAID_VOL_STATE_INITIALIZING (0x02)
#define MPI2_RAID_VOL_STATE_ONLINE (0x03)
#define MPI2_RAID_VOL_STATE_DEGRADED (0x04)
#define MPI2_RAID_VOL_STATE_OPTIMAL (0x05)
/*values for RAID VolumeType */
#define MPI2_RAID_VOL_TYPE_RAID0 (0x00)
#define MPI2_RAID_VOL_TYPE_RAID1E (0x01)
#define MPI2_RAID_VOL_TYPE_RAID1 (0x02)
#define MPI2_RAID_VOL_TYPE_RAID10 (0x05)
#define MPI2_RAID_VOL_TYPE_UNKNOWN (0xFF)
/*values for RAID Volume Page 0 VolumeStatusFlags field */
#define MPI2_RAIDVOL0_STATUS_FLAG_PENDING_RESYNC (0x02000000)
#define MPI2_RAIDVOL0_STATUS_FLAG_BACKG_INIT_PENDING (0x01000000)
#define MPI2_RAIDVOL0_STATUS_FLAG_MDC_PENDING (0x00800000)
#define MPI2_RAIDVOL0_STATUS_FLAG_USER_CONSIST_PENDING (0x00400000)
#define MPI2_RAIDVOL0_STATUS_FLAG_MAKE_DATA_CONSISTENT (0x00200000)
#define MPI2_RAIDVOL0_STATUS_FLAG_DATA_SCRUB (0x00100000)
#define MPI2_RAIDVOL0_STATUS_FLAG_CONSISTENCY_CHECK (0x00080000)
#define MPI2_RAIDVOL0_STATUS_FLAG_CAPACITY_EXPANSION (0x00040000)
#define MPI2_RAIDVOL0_STATUS_FLAG_BACKGROUND_INIT (0x00020000)
#define MPI2_RAIDVOL0_STATUS_FLAG_RESYNC_IN_PROGRESS (0x00010000)
#define MPI2_RAIDVOL0_STATUS_FLAG_VOL_NOT_CONSISTENT (0x00000080)
#define MPI2_RAIDVOL0_STATUS_FLAG_OCE_ALLOWED (0x00000040)
#define MPI2_RAIDVOL0_STATUS_FLAG_BGI_COMPLETE (0x00000020)
#define MPI2_RAIDVOL0_STATUS_FLAG_1E_OFFSET_MIRROR (0x00000000)
#define MPI2_RAIDVOL0_STATUS_FLAG_1E_ADJACENT_MIRROR (0x00000010)
#define MPI2_RAIDVOL0_STATUS_FLAG_BAD_BLOCK_TABLE_FULL (0x00000008)
#define MPI2_RAIDVOL0_STATUS_FLAG_VOLUME_INACTIVE (0x00000004)
#define MPI2_RAIDVOL0_STATUS_FLAG_QUIESCED (0x00000002)
#define MPI2_RAIDVOL0_STATUS_FLAG_ENABLED (0x00000001)
/*values for RAID Volume Page 0 SupportedPhysDisks field */
#define MPI2_RAIDVOL0_SUPPORT_SOLID_STATE_DISKS (0x08)
#define MPI2_RAIDVOL0_SUPPORT_HARD_DISKS (0x04)
#define MPI2_RAIDVOL0_SUPPORT_SAS_PROTOCOL (0x02)
#define MPI2_RAIDVOL0_SUPPORT_SATA_PROTOCOL (0x01)
/*values for RAID Volume Page 0 InactiveStatus field */
#define MPI2_RAIDVOLPAGE0_UNKNOWN_INACTIVE (0x00)
#define MPI2_RAIDVOLPAGE0_STALE_METADATA_INACTIVE (0x01)
#define MPI2_RAIDVOLPAGE0_FOREIGN_VOLUME_INACTIVE (0x02)
#define MPI2_RAIDVOLPAGE0_INSUFFICIENT_RESOURCE_INACTIVE (0x03)
#define MPI2_RAIDVOLPAGE0_CLONE_VOLUME_INACTIVE (0x04)
#define MPI2_RAIDVOLPAGE0_INSUFFICIENT_METADATA_INACTIVE (0x05)
#define MPI2_RAIDVOLPAGE0_PREVIOUSLY_DELETED (0x06)
/*RAID Volume Page 1 */
typedef struct _MPI2_CONFIG_PAGE_RAID_VOL_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U16 DevHandle; /*0x04 */
U16 Reserved0; /*0x06 */
U8 GUID[24]; /*0x08 */
U8 Name[16]; /*0x20 */
U64 WWID; /*0x30 */
U32 Reserved1; /*0x38 */
U32 Reserved2; /*0x3C */
} MPI2_CONFIG_PAGE_RAID_VOL_1,
*PTR_MPI2_CONFIG_PAGE_RAID_VOL_1,
Mpi2RaidVolPage1_t, *pMpi2RaidVolPage1_t;
#define MPI2_RAIDVOLPAGE1_PAGEVERSION (0x03)
/****************************************************************************
* RAID Physical Disk Config Pages
****************************************************************************/
/*RAID Physical Disk Page 0 */
typedef struct _MPI2_RAIDPHYSDISK0_SETTINGS {
U16 Reserved1; /*0x00 */
U8 HotSparePool; /*0x02 */
U8 Reserved2; /*0x03 */
} MPI2_RAIDPHYSDISK0_SETTINGS,
*PTR_MPI2_RAIDPHYSDISK0_SETTINGS,
Mpi2RaidPhysDisk0Settings_t,
*pMpi2RaidPhysDisk0Settings_t;
/*use MPI2_RAID_HOT_SPARE_POOL_ defines for the HotSparePool field */
typedef struct _MPI2_RAIDPHYSDISK0_INQUIRY_DATA {
U8 VendorID[8]; /*0x00 */
U8 ProductID[16]; /*0x08 */
U8 ProductRevLevel[4]; /*0x18 */
U8 SerialNum[32]; /*0x1C */
} MPI2_RAIDPHYSDISK0_INQUIRY_DATA,
*PTR_MPI2_RAIDPHYSDISK0_INQUIRY_DATA,
Mpi2RaidPhysDisk0InquiryData_t,
*pMpi2RaidPhysDisk0InquiryData_t;
typedef struct _MPI2_CONFIG_PAGE_RD_PDISK_0 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U16 DevHandle; /*0x04 */
U8 Reserved1; /*0x06 */
U8 PhysDiskNum; /*0x07 */
MPI2_RAIDPHYSDISK0_SETTINGS PhysDiskSettings; /*0x08 */
U32 Reserved2; /*0x0C */
MPI2_RAIDPHYSDISK0_INQUIRY_DATA InquiryData; /*0x10 */
U32 Reserved3; /*0x4C */
U8 PhysDiskState; /*0x50 */
U8 OfflineReason; /*0x51 */
U8 IncompatibleReason; /*0x52 */
U8 PhysDiskAttributes; /*0x53 */
U32 PhysDiskStatusFlags;/*0x54 */
U64 DeviceMaxLBA; /*0x58 */
U64 HostMaxLBA; /*0x60 */
U64 CoercedMaxLBA; /*0x68 */
U16 BlockSize; /*0x70 */
U16 Reserved5; /*0x72 */
U32 Reserved6; /*0x74 */
} MPI2_CONFIG_PAGE_RD_PDISK_0,
*PTR_MPI2_CONFIG_PAGE_RD_PDISK_0,
Mpi2RaidPhysDiskPage0_t,
*pMpi2RaidPhysDiskPage0_t;
#define MPI2_RAIDPHYSDISKPAGE0_PAGEVERSION (0x05)
/*PhysDiskState defines */
#define MPI2_RAID_PD_STATE_NOT_CONFIGURED (0x00)
#define MPI2_RAID_PD_STATE_NOT_COMPATIBLE (0x01)
#define MPI2_RAID_PD_STATE_OFFLINE (0x02)
#define MPI2_RAID_PD_STATE_ONLINE (0x03)
#define MPI2_RAID_PD_STATE_HOT_SPARE (0x04)
#define MPI2_RAID_PD_STATE_DEGRADED (0x05)
#define MPI2_RAID_PD_STATE_REBUILDING (0x06)
#define MPI2_RAID_PD_STATE_OPTIMAL (0x07)
/*OfflineReason defines */
#define MPI2_PHYSDISK0_ONLINE (0x00)
#define MPI2_PHYSDISK0_OFFLINE_MISSING (0x01)
#define MPI2_PHYSDISK0_OFFLINE_FAILED (0x03)
#define MPI2_PHYSDISK0_OFFLINE_INITIALIZING (0x04)
#define MPI2_PHYSDISK0_OFFLINE_REQUESTED (0x05)
#define MPI2_PHYSDISK0_OFFLINE_FAILED_REQUESTED (0x06)
#define MPI2_PHYSDISK0_OFFLINE_OTHER (0xFF)
/*IncompatibleReason defines */
#define MPI2_PHYSDISK0_COMPATIBLE (0x00)
#define MPI2_PHYSDISK0_INCOMPATIBLE_PROTOCOL (0x01)
#define MPI2_PHYSDISK0_INCOMPATIBLE_BLOCKSIZE (0x02)
#define MPI2_PHYSDISK0_INCOMPATIBLE_MAX_LBA (0x03)
#define MPI2_PHYSDISK0_INCOMPATIBLE_SATA_EXTENDED_CMD (0x04)
#define MPI2_PHYSDISK0_INCOMPATIBLE_REMOVEABLE_MEDIA (0x05)
#define MPI2_PHYSDISK0_INCOMPATIBLE_MEDIA_TYPE (0x06)
#define MPI2_PHYSDISK0_INCOMPATIBLE_UNKNOWN (0xFF)
/*PhysDiskAttributes defines */
#define MPI2_PHYSDISK0_ATTRIB_MEDIA_MASK (0x0C)
#define MPI2_PHYSDISK0_ATTRIB_SOLID_STATE_DRIVE (0x08)
#define MPI2_PHYSDISK0_ATTRIB_HARD_DISK_DRIVE (0x04)
#define MPI2_PHYSDISK0_ATTRIB_PROTOCOL_MASK (0x03)
#define MPI2_PHYSDISK0_ATTRIB_SAS_PROTOCOL (0x02)
#define MPI2_PHYSDISK0_ATTRIB_SATA_PROTOCOL (0x01)
/*PhysDiskStatusFlags defines */
#define MPI2_PHYSDISK0_STATUS_FLAG_NOT_CERTIFIED (0x00000040)
#define MPI2_PHYSDISK0_STATUS_FLAG_OCE_TARGET (0x00000020)
#define MPI2_PHYSDISK0_STATUS_FLAG_WRITE_CACHE_ENABLED (0x00000010)
#define MPI2_PHYSDISK0_STATUS_FLAG_OPTIMAL_PREVIOUS (0x00000000)
#define MPI2_PHYSDISK0_STATUS_FLAG_NOT_OPTIMAL_PREVIOUS (0x00000008)
#define MPI2_PHYSDISK0_STATUS_FLAG_INACTIVE_VOLUME (0x00000004)
#define MPI2_PHYSDISK0_STATUS_FLAG_QUIESCED (0x00000002)
#define MPI2_PHYSDISK0_STATUS_FLAG_OUT_OF_SYNC (0x00000001)
/*RAID Physical Disk Page 1 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhysDiskPaths at runtime.
*/
#ifndef MPI2_RAID_PHYS_DISK1_PATH_MAX
#define MPI2_RAID_PHYS_DISK1_PATH_MAX (1)
#endif
typedef struct _MPI2_RAIDPHYSDISK1_PATH {
U16 DevHandle; /*0x00 */
U16 Reserved1; /*0x02 */
U64 WWID; /*0x04 */
U64 OwnerWWID; /*0x0C */
U8 OwnerIdentifier; /*0x14 */
U8 Reserved2; /*0x15 */
U16 Flags; /*0x16 */
} MPI2_RAIDPHYSDISK1_PATH, *PTR_MPI2_RAIDPHYSDISK1_PATH,
Mpi2RaidPhysDisk1Path_t,
*pMpi2RaidPhysDisk1Path_t;
/*RAID Physical Disk Page 1 Physical Disk Path Flags field defines */
#define MPI2_RAID_PHYSDISK1_FLAG_PRIMARY (0x0004)
#define MPI2_RAID_PHYSDISK1_FLAG_BROKEN (0x0002)
#define MPI2_RAID_PHYSDISK1_FLAG_INVALID (0x0001)
typedef struct _MPI2_CONFIG_PAGE_RD_PDISK_1 {
MPI2_CONFIG_PAGE_HEADER Header; /*0x00 */
U8 NumPhysDiskPaths; /*0x04 */
U8 PhysDiskNum; /*0x05 */
U16 Reserved1; /*0x06 */
U32 Reserved2; /*0x08 */
MPI2_RAIDPHYSDISK1_PATH
PhysicalDiskPath[MPI2_RAID_PHYS_DISK1_PATH_MAX];/*0x0C */
} MPI2_CONFIG_PAGE_RD_PDISK_1,
*PTR_MPI2_CONFIG_PAGE_RD_PDISK_1,
Mpi2RaidPhysDiskPage1_t,
*pMpi2RaidPhysDiskPage1_t;
#define MPI2_RAIDPHYSDISKPAGE1_PAGEVERSION (0x02)
/****************************************************************************
* values for fields used by several types of SAS Config Pages
****************************************************************************/
/*values for NegotiatedLinkRates fields */
#define MPI2_SAS_NEG_LINK_RATE_MASK_LOGICAL (0xF0)
#define MPI2_SAS_NEG_LINK_RATE_SHIFT_LOGICAL (4)
#define MPI2_SAS_NEG_LINK_RATE_MASK_PHYSICAL (0x0F)
/*link rates used for Negotiated Physical and Logical Link Rate */
#define MPI2_SAS_NEG_LINK_RATE_UNKNOWN_LINK_RATE (0x00)
#define MPI2_SAS_NEG_LINK_RATE_PHY_DISABLED (0x01)
#define MPI2_SAS_NEG_LINK_RATE_NEGOTIATION_FAILED (0x02)
#define MPI2_SAS_NEG_LINK_RATE_SATA_OOB_COMPLETE (0x03)
#define MPI2_SAS_NEG_LINK_RATE_PORT_SELECTOR (0x04)
#define MPI2_SAS_NEG_LINK_RATE_SMP_RESET_IN_PROGRESS (0x05)
#define MPI2_SAS_NEG_LINK_RATE_UNSUPPORTED_PHY (0x06)
#define MPI2_SAS_NEG_LINK_RATE_1_5 (0x08)
#define MPI2_SAS_NEG_LINK_RATE_3_0 (0x09)
#define MPI2_SAS_NEG_LINK_RATE_6_0 (0x0A)
#define MPI25_SAS_NEG_LINK_RATE_12_0 (0x0B)
/*values for AttachedPhyInfo fields */
#define MPI2_SAS_APHYINFO_INSIDE_ZPSDS_PERSISTENT (0x00000040)
#define MPI2_SAS_APHYINFO_REQUESTED_INSIDE_ZPSDS (0x00000020)
#define MPI2_SAS_APHYINFO_BREAK_REPLY_CAPABLE (0x00000010)
#define MPI2_SAS_APHYINFO_REASON_MASK (0x0000000F)
#define MPI2_SAS_APHYINFO_REASON_UNKNOWN (0x00000000)
#define MPI2_SAS_APHYINFO_REASON_POWER_ON (0x00000001)
#define MPI2_SAS_APHYINFO_REASON_HARD_RESET (0x00000002)
#define MPI2_SAS_APHYINFO_REASON_SMP_PHY_CONTROL (0x00000003)
#define MPI2_SAS_APHYINFO_REASON_LOSS_OF_SYNC (0x00000004)
#define MPI2_SAS_APHYINFO_REASON_MULTIPLEXING_SEQ (0x00000005)
#define MPI2_SAS_APHYINFO_REASON_IT_NEXUS_LOSS_TIMER (0x00000006)
#define MPI2_SAS_APHYINFO_REASON_BREAK_TIMEOUT (0x00000007)
#define MPI2_SAS_APHYINFO_REASON_PHY_TEST_STOPPED (0x00000008)
/*values for PhyInfo fields */
#define MPI2_SAS_PHYINFO_PHY_VACANT (0x80000000)
#define MPI2_SAS_PHYINFO_PHY_POWER_CONDITION_MASK (0x18000000)
#define MPI2_SAS_PHYINFO_SHIFT_PHY_POWER_CONDITION (27)
#define MPI2_SAS_PHYINFO_PHY_POWER_ACTIVE (0x00000000)
#define MPI2_SAS_PHYINFO_PHY_POWER_PARTIAL (0x08000000)
#define MPI2_SAS_PHYINFO_PHY_POWER_SLUMBER (0x10000000)
#define MPI2_SAS_PHYINFO_CHANGED_REQ_INSIDE_ZPSDS (0x04000000)
#define MPI2_SAS_PHYINFO_INSIDE_ZPSDS_PERSISTENT (0x02000000)
#define MPI2_SAS_PHYINFO_REQ_INSIDE_ZPSDS (0x01000000)
#define MPI2_SAS_PHYINFO_ZONE_GROUP_PERSISTENT (0x00400000)
#define MPI2_SAS_PHYINFO_INSIDE_ZPSDS (0x00200000)
#define MPI2_SAS_PHYINFO_ZONING_ENABLED (0x00100000)
#define MPI2_SAS_PHYINFO_REASON_MASK (0x000F0000)
#define MPI2_SAS_PHYINFO_REASON_UNKNOWN (0x00000000)
#define MPI2_SAS_PHYINFO_REASON_POWER_ON (0x00010000)
#define MPI2_SAS_PHYINFO_REASON_HARD_RESET (0x00020000)
#define MPI2_SAS_PHYINFO_REASON_SMP_PHY_CONTROL (0x00030000)
#define MPI2_SAS_PHYINFO_REASON_LOSS_OF_SYNC (0x00040000)
#define MPI2_SAS_PHYINFO_REASON_MULTIPLEXING_SEQ (0x00050000)
#define MPI2_SAS_PHYINFO_REASON_IT_NEXUS_LOSS_TIMER (0x00060000)
#define MPI2_SAS_PHYINFO_REASON_BREAK_TIMEOUT (0x00070000)
#define MPI2_SAS_PHYINFO_REASON_PHY_TEST_STOPPED (0x00080000)
#define MPI2_SAS_PHYINFO_MULTIPLEXING_SUPPORTED (0x00008000)
#define MPI2_SAS_PHYINFO_SATA_PORT_ACTIVE (0x00004000)
#define MPI2_SAS_PHYINFO_SATA_PORT_SELECTOR_PRESENT (0x00002000)
#define MPI2_SAS_PHYINFO_VIRTUAL_PHY (0x00001000)
#define MPI2_SAS_PHYINFO_MASK_PARTIAL_PATHWAY_TIME (0x00000F00)
#define MPI2_SAS_PHYINFO_SHIFT_PARTIAL_PATHWAY_TIME (8)
#define MPI2_SAS_PHYINFO_MASK_ROUTING_ATTRIBUTE (0x000000F0)
#define MPI2_SAS_PHYINFO_DIRECT_ROUTING (0x00000000)
#define MPI2_SAS_PHYINFO_SUBTRACTIVE_ROUTING (0x00000010)
#define MPI2_SAS_PHYINFO_TABLE_ROUTING (0x00000020)
/*values for SAS ProgrammedLinkRate fields */
#define MPI2_SAS_PRATE_MAX_RATE_MASK (0xF0)
#define MPI2_SAS_PRATE_MAX_RATE_NOT_PROGRAMMABLE (0x00)
#define MPI2_SAS_PRATE_MAX_RATE_1_5 (0x80)
#define MPI2_SAS_PRATE_MAX_RATE_3_0 (0x90)
#define MPI2_SAS_PRATE_MAX_RATE_6_0 (0xA0)
#define MPI25_SAS_PRATE_MAX_RATE_12_0 (0xB0)
#define MPI2_SAS_PRATE_MIN_RATE_MASK (0x0F)
#define MPI2_SAS_PRATE_MIN_RATE_NOT_PROGRAMMABLE (0x00)
#define MPI2_SAS_PRATE_MIN_RATE_1_5 (0x08)
#define MPI2_SAS_PRATE_MIN_RATE_3_0 (0x09)
#define MPI2_SAS_PRATE_MIN_RATE_6_0 (0x0A)
#define MPI25_SAS_PRATE_MIN_RATE_12_0 (0x0B)
/*values for SAS HwLinkRate fields */
#define MPI2_SAS_HWRATE_MAX_RATE_MASK (0xF0)
#define MPI2_SAS_HWRATE_MAX_RATE_1_5 (0x80)
#define MPI2_SAS_HWRATE_MAX_RATE_3_0 (0x90)
#define MPI2_SAS_HWRATE_MAX_RATE_6_0 (0xA0)
#define MPI25_SAS_HWRATE_MAX_RATE_12_0 (0xB0)
#define MPI2_SAS_HWRATE_MIN_RATE_MASK (0x0F)
#define MPI2_SAS_HWRATE_MIN_RATE_1_5 (0x08)
#define MPI2_SAS_HWRATE_MIN_RATE_3_0 (0x09)
#define MPI2_SAS_HWRATE_MIN_RATE_6_0 (0x0A)
#define MPI25_SAS_HWRATE_MIN_RATE_12_0 (0x0B)
/****************************************************************************
* SAS IO Unit Config Pages
****************************************************************************/
/*SAS IO Unit Page 0 */
typedef struct _MPI2_SAS_IO_UNIT0_PHY_DATA {
U8 Port; /*0x00 */
U8 PortFlags; /*0x01 */
U8 PhyFlags; /*0x02 */
U8 NegotiatedLinkRate; /*0x03 */
U32 ControllerPhyDeviceInfo;/*0x04 */
U16 AttachedDevHandle; /*0x08 */
U16 ControllerDevHandle; /*0x0A */
U32 DiscoveryStatus; /*0x0C */
U32 Reserved; /*0x10 */
} MPI2_SAS_IO_UNIT0_PHY_DATA,
*PTR_MPI2_SAS_IO_UNIT0_PHY_DATA,
Mpi2SasIOUnit0PhyData_t,
*pMpi2SasIOUnit0PhyData_t;
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_SAS_IOUNIT0_PHY_MAX
#define MPI2_SAS_IOUNIT0_PHY_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U32 Reserved1;/*0x08 */
U8 NumPhys; /*0x0C */
U8 Reserved2;/*0x0D */
U16 Reserved3;/*0x0E */
MPI2_SAS_IO_UNIT0_PHY_DATA
PhyData[MPI2_SAS_IOUNIT0_PHY_MAX]; /*0x10 */
} MPI2_CONFIG_PAGE_SASIOUNIT_0,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_0,
Mpi2SasIOUnitPage0_t, *pMpi2SasIOUnitPage0_t;
#define MPI2_SASIOUNITPAGE0_PAGEVERSION (0x05)
/*values for SAS IO Unit Page 0 PortFlags */
#define MPI2_SASIOUNIT0_PORTFLAGS_DISCOVERY_IN_PROGRESS (0x08)
#define MPI2_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG (0x01)
/*values for SAS IO Unit Page 0 PhyFlags */
#define MPI2_SASIOUNIT0_PHYFLAGS_ZONING_ENABLED (0x10)
#define MPI2_SASIOUNIT0_PHYFLAGS_PHY_DISABLED (0x08)
/*use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
/*see mpi2_sas.h for values for
*SAS IO Unit Page 0 ControllerPhyDeviceInfo values */
/*values for SAS IO Unit Page 0 DiscoveryStatus */
#define MPI2_SASIOUNIT0_DS_MAX_ENCLOSURES_EXCEED (0x80000000)
#define MPI2_SASIOUNIT0_DS_MAX_EXPANDERS_EXCEED (0x40000000)
#define MPI2_SASIOUNIT0_DS_MAX_DEVICES_EXCEED (0x20000000)
#define MPI2_SASIOUNIT0_DS_MAX_TOPO_PHYS_EXCEED (0x10000000)
#define MPI2_SASIOUNIT0_DS_DOWNSTREAM_INITIATOR (0x08000000)
#define MPI2_SASIOUNIT0_DS_MULTI_SUBTRACTIVE_SUBTRACTIVE (0x00008000)
#define MPI2_SASIOUNIT0_DS_EXP_MULTI_SUBTRACTIVE (0x00004000)
#define MPI2_SASIOUNIT0_DS_MULTI_PORT_DOMAIN (0x00002000)
#define MPI2_SASIOUNIT0_DS_TABLE_TO_SUBTRACTIVE_LINK (0x00001000)
#define MPI2_SASIOUNIT0_DS_UNSUPPORTED_DEVICE (0x00000800)
#define MPI2_SASIOUNIT0_DS_TABLE_LINK (0x00000400)
#define MPI2_SASIOUNIT0_DS_SUBTRACTIVE_LINK (0x00000200)
#define MPI2_SASIOUNIT0_DS_SMP_CRC_ERROR (0x00000100)
#define MPI2_SASIOUNIT0_DS_SMP_FUNCTION_FAILED (0x00000080)
#define MPI2_SASIOUNIT0_DS_INDEX_NOT_EXIST (0x00000040)
#define MPI2_SASIOUNIT0_DS_OUT_ROUTE_ENTRIES (0x00000020)
#define MPI2_SASIOUNIT0_DS_SMP_TIMEOUT (0x00000010)
#define MPI2_SASIOUNIT0_DS_MULTIPLE_PORTS (0x00000004)
#define MPI2_SASIOUNIT0_DS_UNADDRESSABLE_DEVICE (0x00000002)
#define MPI2_SASIOUNIT0_DS_LOOP_DETECTED (0x00000001)
/*SAS IO Unit Page 1 */
typedef struct _MPI2_SAS_IO_UNIT1_PHY_DATA {
U8 Port; /*0x00 */
U8 PortFlags; /*0x01 */
U8 PhyFlags; /*0x02 */
U8 MaxMinLinkRate; /*0x03 */
U32 ControllerPhyDeviceInfo; /*0x04 */
U16 MaxTargetPortConnectTime; /*0x08 */
U16 Reserved1; /*0x0A */
} MPI2_SAS_IO_UNIT1_PHY_DATA,
*PTR_MPI2_SAS_IO_UNIT1_PHY_DATA,
Mpi2SasIOUnit1PhyData_t,
*pMpi2SasIOUnit1PhyData_t;
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_SAS_IOUNIT1_PHY_MAX
#define MPI2_SAS_IOUNIT1_PHY_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_1 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U16
ControlFlags; /*0x08 */
U16
SASNarrowMaxQueueDepth; /*0x0A */
U16
AdditionalControlFlags; /*0x0C */
U16
SASWideMaxQueueDepth; /*0x0E */
U8
NumPhys; /*0x10 */
U8
SATAMaxQDepth; /*0x11 */
U8
ReportDeviceMissingDelay; /*0x12 */
U8
IODeviceMissingDelay; /*0x13 */
MPI2_SAS_IO_UNIT1_PHY_DATA
PhyData[MPI2_SAS_IOUNIT1_PHY_MAX]; /*0x14 */
} MPI2_CONFIG_PAGE_SASIOUNIT_1,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_1,
Mpi2SasIOUnitPage1_t, *pMpi2SasIOUnitPage1_t;
#define MPI2_SASIOUNITPAGE1_PAGEVERSION (0x09)
/*values for SAS IO Unit Page 1 ControlFlags */
#define MPI2_SASIOUNIT1_CONTROL_DEVICE_SELF_TEST (0x8000)
#define MPI2_SASIOUNIT1_CONTROL_SATA_3_0_MAX (0x4000)
#define MPI2_SASIOUNIT1_CONTROL_SATA_1_5_MAX (0x2000)
#define MPI2_SASIOUNIT1_CONTROL_SATA_SW_PRESERVE (0x1000)
#define MPI2_SASIOUNIT1_CONTROL_MASK_DEV_SUPPORT (0x0600)
#define MPI2_SASIOUNIT1_CONTROL_SHIFT_DEV_SUPPORT (9)
#define MPI2_SASIOUNIT1_CONTROL_DEV_SUPPORT_BOTH (0x0)
#define MPI2_SASIOUNIT1_CONTROL_DEV_SAS_SUPPORT (0x1)
#define MPI2_SASIOUNIT1_CONTROL_DEV_SATA_SUPPORT (0x2)
#define MPI2_SASIOUNIT1_CONTROL_SATA_48BIT_LBA_REQUIRED (0x0080)
#define MPI2_SASIOUNIT1_CONTROL_SATA_SMART_REQUIRED (0x0040)
#define MPI2_SASIOUNIT1_CONTROL_SATA_NCQ_REQUIRED (0x0020)
#define MPI2_SASIOUNIT1_CONTROL_SATA_FUA_REQUIRED (0x0010)
#define MPI2_SASIOUNIT1_CONTROL_TABLE_SUBTRACTIVE_ILLEGAL (0x0008)
#define MPI2_SASIOUNIT1_CONTROL_SUBTRACTIVE_ILLEGAL (0x0004)
#define MPI2_SASIOUNIT1_CONTROL_FIRST_LVL_DISC_ONLY (0x0002)
#define MPI2_SASIOUNIT1_CONTROL_CLEAR_AFFILIATION (0x0001)
/*values for SAS IO Unit Page 1 AdditionalControlFlags */
#define MPI2_SASIOUNIT1_ACONTROL_MULTI_PORT_DOMAIN_ILLEGAL (0x0080)
#define MPI2_SASIOUNIT1_ACONTROL_SATA_ASYNCHROUNOUS_NOTIFICATION (0x0040)
#define MPI2_SASIOUNIT1_ACONTROL_INVALID_TOPOLOGY_CORRECTION (0x0020)
#define MPI2_SASIOUNIT1_ACONTROL_PORT_ENABLE_ONLY_SATA_LINK_RESET (0x0010)
#define MPI2_SASIOUNIT1_ACONTROL_OTHER_AFFILIATION_SATA_LINK_RESET (0x0008)
#define MPI2_SASIOUNIT1_ACONTROL_SELF_AFFILIATION_SATA_LINK_RESET (0x0004)
#define MPI2_SASIOUNIT1_ACONTROL_NO_AFFILIATION_SATA_LINK_RESET (0x0002)
#define MPI2_SASIOUNIT1_ACONTROL_ALLOW_TABLE_TO_TABLE (0x0001)
/*defines for SAS IO Unit Page 1 ReportDeviceMissingDelay */
#define MPI2_SASIOUNIT1_REPORT_MISSING_TIMEOUT_MASK (0x7F)
#define MPI2_SASIOUNIT1_REPORT_MISSING_UNIT_16 (0x80)
/*values for SAS IO Unit Page 1 PortFlags */
#define MPI2_SASIOUNIT1_PORT_FLAGS_AUTO_PORT_CONFIG (0x01)
/*values for SAS IO Unit Page 1 PhyFlags */
#define MPI2_SASIOUNIT1_PHYFLAGS_ZONING_ENABLE (0x10)
#define MPI2_SASIOUNIT1_PHYFLAGS_PHY_DISABLE (0x08)
/*values for SAS IO Unit Page 1 MaxMinLinkRate */
#define MPI2_SASIOUNIT1_MAX_RATE_MASK (0xF0)
#define MPI2_SASIOUNIT1_MAX_RATE_1_5 (0x80)
#define MPI2_SASIOUNIT1_MAX_RATE_3_0 (0x90)
#define MPI2_SASIOUNIT1_MAX_RATE_6_0 (0xA0)
#define MPI25_SASIOUNIT1_MAX_RATE_12_0 (0xB0)
#define MPI2_SASIOUNIT1_MIN_RATE_MASK (0x0F)
#define MPI2_SASIOUNIT1_MIN_RATE_1_5 (0x08)
#define MPI2_SASIOUNIT1_MIN_RATE_3_0 (0x09)
#define MPI2_SASIOUNIT1_MIN_RATE_6_0 (0x0A)
#define MPI25_SASIOUNIT1_MIN_RATE_12_0 (0x0B)
/*see mpi2_sas.h for values for
*SAS IO Unit Page 1 ControllerPhyDeviceInfo values */
/*SAS IO Unit Page 4 */
typedef struct _MPI2_SAS_IOUNIT4_SPINUP_GROUP {
U8 MaxTargetSpinup; /*0x00 */
U8 SpinupDelay; /*0x01 */
U8 SpinupFlags; /*0x02 */
U8 Reserved1; /*0x03 */
} MPI2_SAS_IOUNIT4_SPINUP_GROUP,
*PTR_MPI2_SAS_IOUNIT4_SPINUP_GROUP,
Mpi2SasIOUnit4SpinupGroup_t,
*pMpi2SasIOUnit4SpinupGroup_t;
/*defines for SAS IO Unit Page 4 SpinupFlags */
#define MPI2_SASIOUNIT4_SPINUP_DISABLE_FLAG (0x01)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_SAS_IOUNIT4_PHY_MAX
#define MPI2_SAS_IOUNIT4_PHY_MAX (4)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_4 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header;/*0x00 */
MPI2_SAS_IOUNIT4_SPINUP_GROUP
SpinupGroupParameters[4]; /*0x08 */
U32
Reserved1; /*0x18 */
U32
Reserved2; /*0x1C */
U32
Reserved3; /*0x20 */
U8
BootDeviceWaitTime; /*0x24 */
U8
Reserved4; /*0x25 */
U16
Reserved5; /*0x26 */
U8
NumPhys; /*0x28 */
U8
PEInitialSpinupDelay; /*0x29 */
U8
PEReplyDelay; /*0x2A */
U8
Flags; /*0x2B */
U8
PHY[MPI2_SAS_IOUNIT4_PHY_MAX]; /*0x2C */
} MPI2_CONFIG_PAGE_SASIOUNIT_4,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_4,
Mpi2SasIOUnitPage4_t, *pMpi2SasIOUnitPage4_t;
#define MPI2_SASIOUNITPAGE4_PAGEVERSION (0x02)
/*defines for Flags field */
#define MPI2_SASIOUNIT4_FLAGS_AUTO_PORTENABLE (0x01)
/*defines for PHY field */
#define MPI2_SASIOUNIT4_PHY_SPINUP_GROUP_MASK (0x03)
/*SAS IO Unit Page 5 */
typedef struct _MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS {
U8 ControlFlags; /*0x00 */
U8 PortWidthModGroup; /*0x01 */
U16 InactivityTimerExponent; /*0x02 */
U8 SATAPartialTimeout; /*0x04 */
U8 Reserved2; /*0x05 */
U8 SATASlumberTimeout; /*0x06 */
U8 Reserved3; /*0x07 */
U8 SASPartialTimeout; /*0x08 */
U8 Reserved4; /*0x09 */
U8 SASSlumberTimeout; /*0x0A */
U8 Reserved5; /*0x0B */
} MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS,
*PTR_MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS,
Mpi2SasIOUnit5PhyPmSettings_t,
*pMpi2SasIOUnit5PhyPmSettings_t;
/*defines for ControlFlags field */
#define MPI2_SASIOUNIT5_CONTROL_SAS_SLUMBER_ENABLE (0x08)
#define MPI2_SASIOUNIT5_CONTROL_SAS_PARTIAL_ENABLE (0x04)
#define MPI2_SASIOUNIT5_CONTROL_SATA_SLUMBER_ENABLE (0x02)
#define MPI2_SASIOUNIT5_CONTROL_SATA_PARTIAL_ENABLE (0x01)
/*defines for PortWidthModeGroup field */
#define MPI2_SASIOUNIT5_PWMG_DISABLE (0xFF)
/*defines for InactivityTimerExponent field */
#define MPI2_SASIOUNIT5_ITE_MASK_SAS_SLUMBER (0x7000)
#define MPI2_SASIOUNIT5_ITE_SHIFT_SAS_SLUMBER (12)
#define MPI2_SASIOUNIT5_ITE_MASK_SAS_PARTIAL (0x0700)
#define MPI2_SASIOUNIT5_ITE_SHIFT_SAS_PARTIAL (8)
#define MPI2_SASIOUNIT5_ITE_MASK_SATA_SLUMBER (0x0070)
#define MPI2_SASIOUNIT5_ITE_SHIFT_SATA_SLUMBER (4)
#define MPI2_SASIOUNIT5_ITE_MASK_SATA_PARTIAL (0x0007)
#define MPI2_SASIOUNIT5_ITE_SHIFT_SATA_PARTIAL (0)
#define MPI2_SASIOUNIT5_ITE_TEN_SECONDS (7)
#define MPI2_SASIOUNIT5_ITE_ONE_SECOND (6)
#define MPI2_SASIOUNIT5_ITE_HUNDRED_MILLISECONDS (5)
#define MPI2_SASIOUNIT5_ITE_TEN_MILLISECONDS (4)
#define MPI2_SASIOUNIT5_ITE_ONE_MILLISECOND (3)
#define MPI2_SASIOUNIT5_ITE_HUNDRED_MICROSECONDS (2)
#define MPI2_SASIOUNIT5_ITE_TEN_MICROSECONDS (1)
#define MPI2_SASIOUNIT5_ITE_ONE_MICROSECOND (0)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhys at runtime.
*/
#ifndef MPI2_SAS_IOUNIT5_PHY_MAX
#define MPI2_SAS_IOUNIT5_PHY_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_5 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U8 NumPhys; /*0x08 */
U8 Reserved1;/*0x09 */
U16 Reserved2;/*0x0A */
U32 Reserved3;/*0x0C */
MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS
SASPhyPowerManagementSettings[MPI2_SAS_IOUNIT5_PHY_MAX];/*0x10 */
} MPI2_CONFIG_PAGE_SASIOUNIT_5,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_5,
Mpi2SasIOUnitPage5_t, *pMpi2SasIOUnitPage5_t;
#define MPI2_SASIOUNITPAGE5_PAGEVERSION (0x01)
/*SAS IO Unit Page 6 */
typedef struct _MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS {
U8 CurrentStatus; /*0x00 */
U8 CurrentModulation; /*0x01 */
U8 CurrentUtilization; /*0x02 */
U8 Reserved1; /*0x03 */
U32 Reserved2; /*0x04 */
} MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS,
*PTR_MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS,
Mpi2SasIOUnit6PortWidthModGroupStatus_t,
*pMpi2SasIOUnit6PortWidthModGroupStatus_t;
/*defines for CurrentStatus field */
#define MPI2_SASIOUNIT6_STATUS_UNAVAILABLE (0x00)
#define MPI2_SASIOUNIT6_STATUS_UNCONFIGURED (0x01)
#define MPI2_SASIOUNIT6_STATUS_INVALID_CONFIG (0x02)
#define MPI2_SASIOUNIT6_STATUS_LINK_DOWN (0x03)
#define MPI2_SASIOUNIT6_STATUS_OBSERVATION_ONLY (0x04)
#define MPI2_SASIOUNIT6_STATUS_INACTIVE (0x05)
#define MPI2_SASIOUNIT6_STATUS_ACTIVE_IOUNIT (0x06)
#define MPI2_SASIOUNIT6_STATUS_ACTIVE_HOST (0x07)
/*defines for CurrentModulation field */
#define MPI2_SASIOUNIT6_MODULATION_25_PERCENT (0x00)
#define MPI2_SASIOUNIT6_MODULATION_50_PERCENT (0x01)
#define MPI2_SASIOUNIT6_MODULATION_75_PERCENT (0x02)
#define MPI2_SASIOUNIT6_MODULATION_100_PERCENT (0x03)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumGroups at runtime.
*/
#ifndef MPI2_SAS_IOUNIT6_GROUP_MAX
#define MPI2_SAS_IOUNIT6_GROUP_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_6 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x08 */
U32 Reserved2; /*0x0C */
U8 NumGroups; /*0x10 */
U8 Reserved3; /*0x11 */
U16 Reserved4; /*0x12 */
MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS
PortWidthModulationGroupStatus[MPI2_SAS_IOUNIT6_GROUP_MAX]; /*0x14 */
} MPI2_CONFIG_PAGE_SASIOUNIT_6,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_6,
Mpi2SasIOUnitPage6_t, *pMpi2SasIOUnitPage6_t;
#define MPI2_SASIOUNITPAGE6_PAGEVERSION (0x00)
/*SAS IO Unit Page 7 */
typedef struct _MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS {
U8 Flags; /*0x00 */
U8 Reserved1; /*0x01 */
U16 Reserved2; /*0x02 */
U8 Threshold75Pct; /*0x04 */
U8 Threshold50Pct; /*0x05 */
U8 Threshold25Pct; /*0x06 */
U8 Reserved3; /*0x07 */
} MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS,
*PTR_MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS,
Mpi2SasIOUnit7PortWidthModGroupSettings_t,
*pMpi2SasIOUnit7PortWidthModGroupSettings_t;
/*defines for Flags field */
#define MPI2_SASIOUNIT7_FLAGS_ENABLE_PORT_WIDTH_MODULATION (0x01)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumGroups at runtime.
*/
#ifndef MPI2_SAS_IOUNIT7_GROUP_MAX
#define MPI2_SAS_IOUNIT7_GROUP_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_7 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U8 SamplingInterval; /*0x08 */
U8 WindowLength; /*0x09 */
U16 Reserved1; /*0x0A */
U32 Reserved2; /*0x0C */
U32 Reserved3; /*0x10 */
U8 NumGroups; /*0x14 */
U8 Reserved4; /*0x15 */
U16 Reserved5; /*0x16 */
MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS
PortWidthModulationGroupSettings[MPI2_SAS_IOUNIT7_GROUP_MAX];/*0x18 */
} MPI2_CONFIG_PAGE_SASIOUNIT_7,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_7,
Mpi2SasIOUnitPage7_t, *pMpi2SasIOUnitPage7_t;
#define MPI2_SASIOUNITPAGE7_PAGEVERSION (0x00)
/*SAS IO Unit Page 8 */
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_8 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U32
PowerManagementCapabilities; /*0x0C */
U8
TxRxSleepStatus; /*0x10 */
U8
Reserved2; /*0x11 */
U16
Reserved3; /*0x12 */
} MPI2_CONFIG_PAGE_SASIOUNIT_8,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT_8,
Mpi2SasIOUnitPage8_t, *pMpi2SasIOUnitPage8_t;
#define MPI2_SASIOUNITPAGE8_PAGEVERSION (0x00)
/*defines for PowerManagementCapabilities field */
#define MPI2_SASIOUNIT8_PM_HOST_PORT_WIDTH_MOD (0x00001000)
#define MPI2_SASIOUNIT8_PM_HOST_SAS_SLUMBER_MODE (0x00000800)
#define MPI2_SASIOUNIT8_PM_HOST_SAS_PARTIAL_MODE (0x00000400)
#define MPI2_SASIOUNIT8_PM_HOST_SATA_SLUMBER_MODE (0x00000200)
#define MPI2_SASIOUNIT8_PM_HOST_SATA_PARTIAL_MODE (0x00000100)
#define MPI2_SASIOUNIT8_PM_IOUNIT_PORT_WIDTH_MOD (0x00000010)
#define MPI2_SASIOUNIT8_PM_IOUNIT_SAS_SLUMBER_MODE (0x00000008)
#define MPI2_SASIOUNIT8_PM_IOUNIT_SAS_PARTIAL_MODE (0x00000004)
#define MPI2_SASIOUNIT8_PM_IOUNIT_SATA_SLUMBER_MODE (0x00000002)
#define MPI2_SASIOUNIT8_PM_IOUNIT_SATA_PARTIAL_MODE (0x00000001)
/*defines for TxRxSleepStatus field */
#define MPI25_SASIOUNIT8_TXRXSLEEP_UNSUPPORTED (0x00)
#define MPI25_SASIOUNIT8_TXRXSLEEP_DISENGAGED (0x01)
#define MPI25_SASIOUNIT8_TXRXSLEEP_ACTIVE (0x02)
#define MPI25_SASIOUNIT8_TXRXSLEEP_SHUTDOWN (0x03)
/*SAS IO Unit Page 16 */
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT16 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U64
TimeStamp; /*0x08 */
U32
Reserved1; /*0x10 */
U32
Reserved2; /*0x14 */
U32
FastPathPendedRequests; /*0x18 */
U32
FastPathUnPendedRequests; /*0x1C */
U32
FastPathHostRequestStarts; /*0x20 */
U32
FastPathFirmwareRequestStarts; /*0x24 */
U32
FastPathHostCompletions; /*0x28 */
U32
FastPathFirmwareCompletions; /*0x2C */
U32
NonFastPathRequestStarts; /*0x30 */
U32
NonFastPathHostCompletions; /*0x30 */
} MPI2_CONFIG_PAGE_SASIOUNIT16,
*PTR_MPI2_CONFIG_PAGE_SASIOUNIT16,
Mpi2SasIOUnitPage16_t, *pMpi2SasIOUnitPage16_t;
#define MPI2_SASIOUNITPAGE16_PAGEVERSION (0x00)
/****************************************************************************
* SAS Expander Config Pages
****************************************************************************/
/*SAS Expander Page 0 */
typedef struct _MPI2_CONFIG_PAGE_EXPANDER_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U8
PhysicalPort; /*0x08 */
U8
ReportGenLength; /*0x09 */
U16
EnclosureHandle; /*0x0A */
U64
SASAddress; /*0x0C */
U32
DiscoveryStatus; /*0x14 */
U16
DevHandle; /*0x18 */
U16
ParentDevHandle; /*0x1A */
U16
ExpanderChangeCount; /*0x1C */
U16
ExpanderRouteIndexes; /*0x1E */
U8
NumPhys; /*0x20 */
U8
SASLevel; /*0x21 */
U16
Flags; /*0x22 */
U16
STPBusInactivityTimeLimit; /*0x24 */
U16
STPMaxConnectTimeLimit; /*0x26 */
U16
STP_SMP_NexusLossTime; /*0x28 */
U16
MaxNumRoutedSasAddresses; /*0x2A */
U64
ActiveZoneManagerSASAddress;/*0x2C */
U16
ZoneLockInactivityLimit; /*0x34 */
U16
Reserved1; /*0x36 */
U8
TimeToReducedFunc; /*0x38 */
U8
InitialTimeToReducedFunc; /*0x39 */
U8
MaxReducedFuncTime; /*0x3A */
U8
Reserved2; /*0x3B */
} MPI2_CONFIG_PAGE_EXPANDER_0,
*PTR_MPI2_CONFIG_PAGE_EXPANDER_0,
Mpi2ExpanderPage0_t, *pMpi2ExpanderPage0_t;
#define MPI2_SASEXPANDER0_PAGEVERSION (0x06)
/*values for SAS Expander Page 0 DiscoveryStatus field */
#define MPI2_SAS_EXPANDER0_DS_MAX_ENCLOSURES_EXCEED (0x80000000)
#define MPI2_SAS_EXPANDER0_DS_MAX_EXPANDERS_EXCEED (0x40000000)
#define MPI2_SAS_EXPANDER0_DS_MAX_DEVICES_EXCEED (0x20000000)
#define MPI2_SAS_EXPANDER0_DS_MAX_TOPO_PHYS_EXCEED (0x10000000)
#define MPI2_SAS_EXPANDER0_DS_DOWNSTREAM_INITIATOR (0x08000000)
#define MPI2_SAS_EXPANDER0_DS_MULTI_SUBTRACTIVE_SUBTRACTIVE (0x00008000)
#define MPI2_SAS_EXPANDER0_DS_EXP_MULTI_SUBTRACTIVE (0x00004000)
#define MPI2_SAS_EXPANDER0_DS_MULTI_PORT_DOMAIN (0x00002000)
#define MPI2_SAS_EXPANDER0_DS_TABLE_TO_SUBTRACTIVE_LINK (0x00001000)
#define MPI2_SAS_EXPANDER0_DS_UNSUPPORTED_DEVICE (0x00000800)
#define MPI2_SAS_EXPANDER0_DS_TABLE_LINK (0x00000400)
#define MPI2_SAS_EXPANDER0_DS_SUBTRACTIVE_LINK (0x00000200)
#define MPI2_SAS_EXPANDER0_DS_SMP_CRC_ERROR (0x00000100)
#define MPI2_SAS_EXPANDER0_DS_SMP_FUNCTION_FAILED (0x00000080)
#define MPI2_SAS_EXPANDER0_DS_INDEX_NOT_EXIST (0x00000040)
#define MPI2_SAS_EXPANDER0_DS_OUT_ROUTE_ENTRIES (0x00000020)
#define MPI2_SAS_EXPANDER0_DS_SMP_TIMEOUT (0x00000010)
#define MPI2_SAS_EXPANDER0_DS_MULTIPLE_PORTS (0x00000004)
#define MPI2_SAS_EXPANDER0_DS_UNADDRESSABLE_DEVICE (0x00000002)
#define MPI2_SAS_EXPANDER0_DS_LOOP_DETECTED (0x00000001)
/*values for SAS Expander Page 0 Flags field */
#define MPI2_SAS_EXPANDER0_FLAGS_REDUCED_FUNCTIONALITY (0x2000)
#define MPI2_SAS_EXPANDER0_FLAGS_ZONE_LOCKED (0x1000)
#define MPI2_SAS_EXPANDER0_FLAGS_SUPPORTED_PHYSICAL_PRES (0x0800)
#define MPI2_SAS_EXPANDER0_FLAGS_ASSERTED_PHYSICAL_PRES (0x0400)
#define MPI2_SAS_EXPANDER0_FLAGS_ZONING_SUPPORT (0x0200)
#define MPI2_SAS_EXPANDER0_FLAGS_ENABLED_ZONING (0x0100)
#define MPI2_SAS_EXPANDER0_FLAGS_TABLE_TO_TABLE_SUPPORT (0x0080)
#define MPI2_SAS_EXPANDER0_FLAGS_CONNECTOR_END_DEVICE (0x0010)
#define MPI2_SAS_EXPANDER0_FLAGS_OTHERS_CONFIG (0x0004)
#define MPI2_SAS_EXPANDER0_FLAGS_CONFIG_IN_PROGRESS (0x0002)
#define MPI2_SAS_EXPANDER0_FLAGS_ROUTE_TABLE_CONFIG (0x0001)
/*SAS Expander Page 1 */
typedef struct _MPI2_CONFIG_PAGE_EXPANDER_1 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U8
PhysicalPort; /*0x08 */
U8
Reserved1; /*0x09 */
U16
Reserved2; /*0x0A */
U8
NumPhys; /*0x0C */
U8
Phy; /*0x0D */
U16
NumTableEntriesProgrammed; /*0x0E */
U8
ProgrammedLinkRate; /*0x10 */
U8
HwLinkRate; /*0x11 */
U16
AttachedDevHandle; /*0x12 */
U32
PhyInfo; /*0x14 */
U32
AttachedDeviceInfo; /*0x18 */
U16
ExpanderDevHandle; /*0x1C */
U8
ChangeCount; /*0x1E */
U8
NegotiatedLinkRate; /*0x1F */
U8
PhyIdentifier; /*0x20 */
U8
AttachedPhyIdentifier; /*0x21 */
U8
Reserved3; /*0x22 */
U8
DiscoveryInfo; /*0x23 */
U32
AttachedPhyInfo; /*0x24 */
U8
ZoneGroup; /*0x28 */
U8
SelfConfigStatus; /*0x29 */
U16
Reserved4; /*0x2A */
} MPI2_CONFIG_PAGE_EXPANDER_1,
*PTR_MPI2_CONFIG_PAGE_EXPANDER_1,
Mpi2ExpanderPage1_t, *pMpi2ExpanderPage1_t;
#define MPI2_SASEXPANDER1_PAGEVERSION (0x02)
/*use MPI2_SAS_PRATE_ defines for the ProgrammedLinkRate field */
/*use MPI2_SAS_HWRATE_ defines for the HwLinkRate field */
/*use MPI2_SAS_PHYINFO_ for the PhyInfo field */
/*see mpi2_sas.h for the MPI2_SAS_DEVICE_INFO_ defines
*used for the AttachedDeviceInfo field */
/*use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
/*values for SAS Expander Page 1 DiscoveryInfo field */
#define MPI2_SAS_EXPANDER1_DISCINFO_BAD_PHY_DISABLED (0x04)
#define MPI2_SAS_EXPANDER1_DISCINFO_LINK_STATUS_CHANGE (0x02)
#define MPI2_SAS_EXPANDER1_DISCINFO_NO_ROUTING_ENTRIES (0x01)
/*use MPI2_SAS_APHYINFO_ defines for AttachedPhyInfo field */
/****************************************************************************
* SAS Device Config Pages
****************************************************************************/
/*SAS Device Page 0 */
typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U16
Slot; /*0x08 */
U16
EnclosureHandle; /*0x0A */
U64
SASAddress; /*0x0C */
U16
ParentDevHandle; /*0x14 */
U8
PhyNum; /*0x16 */
U8
AccessStatus; /*0x17 */
U16
DevHandle; /*0x18 */
U8
AttachedPhyIdentifier; /*0x1A */
U8
ZoneGroup; /*0x1B */
U32
DeviceInfo; /*0x1C */
U16
Flags; /*0x20 */
U8
PhysicalPort; /*0x22 */
U8
MaxPortConnections; /*0x23 */
U64
DeviceName; /*0x24 */
U8
PortGroups; /*0x2C */
U8
DmaGroup; /*0x2D */
U8
ControlGroup; /*0x2E */
U8
Reserved1; /*0x2F */
U32
Reserved2; /*0x30 */
U32
Reserved3; /*0x34 */
} MPI2_CONFIG_PAGE_SAS_DEV_0,
*PTR_MPI2_CONFIG_PAGE_SAS_DEV_0,
Mpi2SasDevicePage0_t,
*pMpi2SasDevicePage0_t;
#define MPI2_SASDEVICE0_PAGEVERSION (0x08)
/*values for SAS Device Page 0 AccessStatus field */
#define MPI2_SAS_DEVICE0_ASTATUS_NO_ERRORS (0x00)
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_INIT_FAILED (0x01)
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_CAPABILITY_FAILED (0x02)
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_AFFILIATION_CONFLICT (0x03)
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_NEEDS_INITIALIZATION (0x04)
#define MPI2_SAS_DEVICE0_ASTATUS_ROUTE_NOT_ADDRESSABLE (0x05)
#define MPI2_SAS_DEVICE0_ASTATUS_SMP_ERROR_NOT_ADDRESSABLE (0x06)
#define MPI2_SAS_DEVICE0_ASTATUS_DEVICE_BLOCKED (0x07)
/*specific values for SATA Init failures */
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_UNKNOWN (0x10)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_AFFILIATION_CONFLICT (0x11)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_DIAG (0x12)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_IDENTIFICATION (0x13)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_CHECK_POWER (0x14)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_PIO_SN (0x15)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_MDMA_SN (0x16)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_UDMA_SN (0x17)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_ZONING_VIOLATION (0x18)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_NOT_ADDRESSABLE (0x19)
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_MAX (0x1F)
/*see mpi2_sas.h for values for SAS Device Page 0 DeviceInfo values */
/*values for SAS Device Page 0 Flags field */
#define MPI2_SAS_DEVICE0_FLAGS_UNAUTHORIZED_DEVICE (0x8000)
#define MPI25_SAS_DEVICE0_FLAGS_ENABLED_FAST_PATH (0x4000)
#define MPI25_SAS_DEVICE0_FLAGS_FAST_PATH_CAPABLE (0x2000)
#define MPI2_SAS_DEVICE0_FLAGS_SLUMBER_PM_CAPABLE (0x1000)
#define MPI2_SAS_DEVICE0_FLAGS_PARTIAL_PM_CAPABLE (0x0800)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_ASYNCHRONOUS_NOTIFY (0x0400)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_SW_PRESERVE (0x0200)
#define MPI2_SAS_DEVICE0_FLAGS_UNSUPPORTED_DEVICE (0x0100)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_48BIT_LBA_SUPPORTED (0x0080)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_SMART_SUPPORTED (0x0040)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_NCQ_SUPPORTED (0x0020)
#define MPI2_SAS_DEVICE0_FLAGS_SATA_FUA_SUPPORTED (0x0010)
#define MPI2_SAS_DEVICE0_FLAGS_PORT_SELECTOR_ATTACH (0x0008)
#define MPI2_SAS_DEVICE0_FLAGS_DEVICE_PRESENT (0x0001)
/*SAS Device Page 1 */
typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_1 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U64
SASAddress; /*0x0C */
U32
Reserved2; /*0x14 */
U16
DevHandle; /*0x18 */
U16
Reserved3; /*0x1A */
U8
InitialRegDeviceFIS[20];/*0x1C */
} MPI2_CONFIG_PAGE_SAS_DEV_1,
*PTR_MPI2_CONFIG_PAGE_SAS_DEV_1,
Mpi2SasDevicePage1_t,
*pMpi2SasDevicePage1_t;
#define MPI2_SASDEVICE1_PAGEVERSION (0x01)
/****************************************************************************
* SAS PHY Config Pages
****************************************************************************/
/*SAS PHY Page 0 */
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U16
OwnerDevHandle; /*0x08 */
U16
Reserved1; /*0x0A */
U16
AttachedDevHandle; /*0x0C */
U8
AttachedPhyIdentifier; /*0x0E */
U8
Reserved2; /*0x0F */
U32
AttachedPhyInfo; /*0x10 */
U8
ProgrammedLinkRate; /*0x14 */
U8
HwLinkRate; /*0x15 */
U8
ChangeCount; /*0x16 */
U8
Flags; /*0x17 */
U32
PhyInfo; /*0x18 */
U8
NegotiatedLinkRate; /*0x1C */
U8
Reserved3; /*0x1D */
U16
Reserved4; /*0x1E */
} MPI2_CONFIG_PAGE_SAS_PHY_0,
*PTR_MPI2_CONFIG_PAGE_SAS_PHY_0,
Mpi2SasPhyPage0_t, *pMpi2SasPhyPage0_t;
#define MPI2_SASPHY0_PAGEVERSION (0x03)
/*use MPI2_SAS_APHYINFO_ defines for AttachedPhyInfo field */
/*use MPI2_SAS_PRATE_ defines for the ProgrammedLinkRate field */
/*use MPI2_SAS_HWRATE_ defines for the HwLinkRate field */
/*values for SAS PHY Page 0 Flags field */
#define MPI2_SAS_PHY0_FLAGS_SGPIO_DIRECT_ATTACH_ENC (0x01)
/*use MPI2_SAS_PHYINFO_ for the PhyInfo field */
/*use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
/*SAS PHY Page 1 */
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_1 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U32
InvalidDwordCount; /*0x0C */
U32
RunningDisparityErrorCount; /*0x10 */
U32
LossDwordSynchCount; /*0x14 */
U32
PhyResetProblemCount; /*0x18 */
} MPI2_CONFIG_PAGE_SAS_PHY_1,
*PTR_MPI2_CONFIG_PAGE_SAS_PHY_1,
Mpi2SasPhyPage1_t, *pMpi2SasPhyPage1_t;
#define MPI2_SASPHY1_PAGEVERSION (0x01)
/*SAS PHY Page 2 */
typedef struct _MPI2_SASPHY2_PHY_EVENT {
U8 PhyEventCode; /*0x00 */
U8 Reserved1; /*0x01 */
U16 Reserved2; /*0x02 */
U32 PhyEventInfo; /*0x04 */
} MPI2_SASPHY2_PHY_EVENT, *PTR_MPI2_SASPHY2_PHY_EVENT,
Mpi2SasPhy2PhyEvent_t, *pMpi2SasPhy2PhyEvent_t;
/*use MPI2_SASPHY3_EVENT_CODE_ for the PhyEventCode field */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhyEvents at runtime.
*/
#ifndef MPI2_SASPHY2_PHY_EVENT_MAX
#define MPI2_SASPHY2_PHY_EVENT_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_2 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U8
NumPhyEvents; /*0x0C */
U8
Reserved2; /*0x0D */
U16
Reserved3; /*0x0E */
MPI2_SASPHY2_PHY_EVENT
PhyEvent[MPI2_SASPHY2_PHY_EVENT_MAX]; /*0x10 */
} MPI2_CONFIG_PAGE_SAS_PHY_2,
*PTR_MPI2_CONFIG_PAGE_SAS_PHY_2,
Mpi2SasPhyPage2_t,
*pMpi2SasPhyPage2_t;
#define MPI2_SASPHY2_PAGEVERSION (0x00)
/*SAS PHY Page 3 */
typedef struct _MPI2_SASPHY3_PHY_EVENT_CONFIG {
U8 PhyEventCode; /*0x00 */
U8 Reserved1; /*0x01 */
U16 Reserved2; /*0x02 */
U8 CounterType; /*0x04 */
U8 ThresholdWindow; /*0x05 */
U8 TimeUnits; /*0x06 */
U8 Reserved3; /*0x07 */
U32 EventThreshold; /*0x08 */
U16 ThresholdFlags; /*0x0C */
U16 Reserved4; /*0x0E */
} MPI2_SASPHY3_PHY_EVENT_CONFIG,
*PTR_MPI2_SASPHY3_PHY_EVENT_CONFIG,
Mpi2SasPhy3PhyEventConfig_t,
*pMpi2SasPhy3PhyEventConfig_t;
/*values for PhyEventCode field */
#define MPI2_SASPHY3_EVENT_CODE_NO_EVENT (0x00)
#define MPI2_SASPHY3_EVENT_CODE_INVALID_DWORD (0x01)
#define MPI2_SASPHY3_EVENT_CODE_RUNNING_DISPARITY_ERROR (0x02)
#define MPI2_SASPHY3_EVENT_CODE_LOSS_DWORD_SYNC (0x03)
#define MPI2_SASPHY3_EVENT_CODE_PHY_RESET_PROBLEM (0x04)
#define MPI2_SASPHY3_EVENT_CODE_ELASTICITY_BUF_OVERFLOW (0x05)
#define MPI2_SASPHY3_EVENT_CODE_RX_ERROR (0x06)
#define MPI2_SASPHY3_EVENT_CODE_RX_ADDR_FRAME_ERROR (0x20)
#define MPI2_SASPHY3_EVENT_CODE_TX_AC_OPEN_REJECT (0x21)
#define MPI2_SASPHY3_EVENT_CODE_RX_AC_OPEN_REJECT (0x22)
#define MPI2_SASPHY3_EVENT_CODE_TX_RC_OPEN_REJECT (0x23)
#define MPI2_SASPHY3_EVENT_CODE_RX_RC_OPEN_REJECT (0x24)
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP_PARTIAL_WAITING_ON (0x25)
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP_CONNECT_WAITING_ON (0x26)
#define MPI2_SASPHY3_EVENT_CODE_TX_BREAK (0x27)
#define MPI2_SASPHY3_EVENT_CODE_RX_BREAK (0x28)
#define MPI2_SASPHY3_EVENT_CODE_BREAK_TIMEOUT (0x29)
#define MPI2_SASPHY3_EVENT_CODE_CONNECTION (0x2A)
#define MPI2_SASPHY3_EVENT_CODE_PEAKTX_PATHWAY_BLOCKED (0x2B)
#define MPI2_SASPHY3_EVENT_CODE_PEAKTX_ARB_WAIT_TIME (0x2C)
#define MPI2_SASPHY3_EVENT_CODE_PEAK_ARB_WAIT_TIME (0x2D)
#define MPI2_SASPHY3_EVENT_CODE_PEAK_CONNECT_TIME (0x2E)
#define MPI2_SASPHY3_EVENT_CODE_TX_SSP_FRAMES (0x40)
#define MPI2_SASPHY3_EVENT_CODE_RX_SSP_FRAMES (0x41)
#define MPI2_SASPHY3_EVENT_CODE_TX_SSP_ERROR_FRAMES (0x42)
#define MPI2_SASPHY3_EVENT_CODE_RX_SSP_ERROR_FRAMES (0x43)
#define MPI2_SASPHY3_EVENT_CODE_TX_CREDIT_BLOCKED (0x44)
#define MPI2_SASPHY3_EVENT_CODE_RX_CREDIT_BLOCKED (0x45)
#define MPI2_SASPHY3_EVENT_CODE_TX_SATA_FRAMES (0x50)
#define MPI2_SASPHY3_EVENT_CODE_RX_SATA_FRAMES (0x51)
#define MPI2_SASPHY3_EVENT_CODE_SATA_OVERFLOW (0x52)
#define MPI2_SASPHY3_EVENT_CODE_TX_SMP_FRAMES (0x60)
#define MPI2_SASPHY3_EVENT_CODE_RX_SMP_FRAMES (0x61)
#define MPI2_SASPHY3_EVENT_CODE_RX_SMP_ERROR_FRAMES (0x63)
#define MPI2_SASPHY3_EVENT_CODE_HOTPLUG_TIMEOUT (0xD0)
#define MPI2_SASPHY3_EVENT_CODE_MISALIGNED_MUX_PRIMITIVE (0xD1)
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP (0xD2)
/*values for the CounterType field */
#define MPI2_SASPHY3_COUNTER_TYPE_WRAPPING (0x00)
#define MPI2_SASPHY3_COUNTER_TYPE_SATURATING (0x01)
#define MPI2_SASPHY3_COUNTER_TYPE_PEAK_VALUE (0x02)
/*values for the TimeUnits field */
#define MPI2_SASPHY3_TIME_UNITS_10_MICROSECONDS (0x00)
#define MPI2_SASPHY3_TIME_UNITS_100_MICROSECONDS (0x01)
#define MPI2_SASPHY3_TIME_UNITS_1_MILLISECOND (0x02)
#define MPI2_SASPHY3_TIME_UNITS_10_MILLISECONDS (0x03)
/*values for the ThresholdFlags field */
#define MPI2_SASPHY3_TFLAGS_PHY_RESET (0x0002)
#define MPI2_SASPHY3_TFLAGS_EVENT_NOTIFY (0x0001)
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumPhyEvents at runtime.
*/
#ifndef MPI2_SASPHY3_PHY_EVENT_MAX
#define MPI2_SASPHY3_PHY_EVENT_MAX (1)
#endif
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_3 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U8
NumPhyEvents; /*0x0C */
U8
Reserved2; /*0x0D */
U16
Reserved3; /*0x0E */
MPI2_SASPHY3_PHY_EVENT_CONFIG
PhyEventConfig[MPI2_SASPHY3_PHY_EVENT_MAX]; /*0x10 */
} MPI2_CONFIG_PAGE_SAS_PHY_3,
*PTR_MPI2_CONFIG_PAGE_SAS_PHY_3,
Mpi2SasPhyPage3_t, *pMpi2SasPhyPage3_t;
#define MPI2_SASPHY3_PAGEVERSION (0x00)
/*SAS PHY Page 4 */
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_4 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U16
Reserved1; /*0x08 */
U8
Reserved2; /*0x0A */
U8
Flags; /*0x0B */
U8
InitialFrame[28]; /*0x0C */
} MPI2_CONFIG_PAGE_SAS_PHY_4,
*PTR_MPI2_CONFIG_PAGE_SAS_PHY_4,
Mpi2SasPhyPage4_t, *pMpi2SasPhyPage4_t;
#define MPI2_SASPHY4_PAGEVERSION (0x00)
/*values for the Flags field */
#define MPI2_SASPHY4_FLAGS_FRAME_VALID (0x02)
#define MPI2_SASPHY4_FLAGS_SATA_FRAME (0x01)
/****************************************************************************
* SAS Port Config Pages
****************************************************************************/
/*SAS Port Page 0 */
typedef struct _MPI2_CONFIG_PAGE_SAS_PORT_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U8
PortNumber; /*0x08 */
U8
PhysicalPort; /*0x09 */
U8
PortWidth; /*0x0A */
U8
PhysicalPortWidth; /*0x0B */
U8
ZoneGroup; /*0x0C */
U8
Reserved1; /*0x0D */
U16
Reserved2; /*0x0E */
U64
SASAddress; /*0x10 */
U32
DeviceInfo; /*0x18 */
U32
Reserved3; /*0x1C */
U32
Reserved4; /*0x20 */
} MPI2_CONFIG_PAGE_SAS_PORT_0,
*PTR_MPI2_CONFIG_PAGE_SAS_PORT_0,
Mpi2SasPortPage0_t, *pMpi2SasPortPage0_t;
#define MPI2_SASPORT0_PAGEVERSION (0x00)
/*see mpi2_sas.h for values for SAS Port Page 0 DeviceInfo values */
/****************************************************************************
* SAS Enclosure Config Pages
****************************************************************************/
/*SAS Enclosure Page 0 */
typedef struct _MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved1; /*0x08 */
U64
EnclosureLogicalID; /*0x0C */
U16
Flags; /*0x14 */
U16
EnclosureHandle; /*0x16 */
U16
NumSlots; /*0x18 */
U16
StartSlot; /*0x1A */
U16
Reserved2; /*0x1C */
U16
SEPDevHandle; /*0x1E */
U32
Reserved3; /*0x20 */
U32
Reserved4; /*0x24 */
} MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0,
*PTR_MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0,
Mpi2SasEnclosurePage0_t, *pMpi2SasEnclosurePage0_t;
#define MPI2_SASENCLOSURE0_PAGEVERSION (0x03)
/*values for SAS Enclosure Page 0 Flags field */
#define MPI2_SAS_ENCLS0_FLAGS_MNG_MASK (0x000F)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_UNKNOWN (0x0000)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_SES (0x0001)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_SGPIO (0x0002)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_EXP_SGPIO (0x0003)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_SES_ENCLOSURE (0x0004)
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_GPIO (0x0005)
/****************************************************************************
* Log Config Page
****************************************************************************/
/*Log Page 0 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumLogEntries at runtime.
*/
#ifndef MPI2_LOG_0_NUM_LOG_ENTRIES
#define MPI2_LOG_0_NUM_LOG_ENTRIES (1)
#endif
#define MPI2_LOG_0_LOG_DATA_LENGTH (0x1C)
typedef struct _MPI2_LOG_0_ENTRY {
U64 TimeStamp; /*0x00 */
U32 Reserved1; /*0x08 */
U16 LogSequence; /*0x0C */
U16 LogEntryQualifier; /*0x0E */
U8 VP_ID; /*0x10 */
U8 VF_ID; /*0x11 */
U16 Reserved2; /*0x12 */
U8
LogData[MPI2_LOG_0_LOG_DATA_LENGTH];/*0x14 */
} MPI2_LOG_0_ENTRY, *PTR_MPI2_LOG_0_ENTRY,
Mpi2Log0Entry_t, *pMpi2Log0Entry_t;
/*values for Log Page 0 LogEntry LogEntryQualifier field */
#define MPI2_LOG_0_ENTRY_QUAL_ENTRY_UNUSED (0x0000)
#define MPI2_LOG_0_ENTRY_QUAL_POWER_ON_RESET (0x0001)
#define MPI2_LOG_0_ENTRY_QUAL_TIMESTAMP_UPDATE (0x0002)
#define MPI2_LOG_0_ENTRY_QUAL_MIN_IMPLEMENT_SPEC (0x8000)
#define MPI2_LOG_0_ENTRY_QUAL_MAX_IMPLEMENT_SPEC (0xFFFF)
typedef struct _MPI2_CONFIG_PAGE_LOG_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U32 Reserved1; /*0x08 */
U32 Reserved2; /*0x0C */
U16 NumLogEntries;/*0x10 */
U16 Reserved3; /*0x12 */
MPI2_LOG_0_ENTRY
LogEntry[MPI2_LOG_0_NUM_LOG_ENTRIES]; /*0x14 */
} MPI2_CONFIG_PAGE_LOG_0, *PTR_MPI2_CONFIG_PAGE_LOG_0,
Mpi2LogPage0_t, *pMpi2LogPage0_t;
#define MPI2_LOG_0_PAGEVERSION (0x02)
/****************************************************************************
* RAID Config Page
****************************************************************************/
/*RAID Page 0 */
/*
*Host code (drivers, BIOS, utilities, etc.) should leave this define set to
*one and check the value returned for NumElements at runtime.
*/
#ifndef MPI2_RAIDCONFIG0_MAX_ELEMENTS
#define MPI2_RAIDCONFIG0_MAX_ELEMENTS (1)
#endif
typedef struct _MPI2_RAIDCONFIG0_CONFIG_ELEMENT {
U16 ElementFlags; /*0x00 */
U16 VolDevHandle; /*0x02 */
U8 HotSparePool; /*0x04 */
U8 PhysDiskNum; /*0x05 */
U16 PhysDiskDevHandle; /*0x06 */
} MPI2_RAIDCONFIG0_CONFIG_ELEMENT,
*PTR_MPI2_RAIDCONFIG0_CONFIG_ELEMENT,
Mpi2RaidConfig0ConfigElement_t,
*pMpi2RaidConfig0ConfigElement_t;
/*values for the ElementFlags field */
#define MPI2_RAIDCONFIG0_EFLAGS_MASK_ELEMENT_TYPE (0x000F)
#define MPI2_RAIDCONFIG0_EFLAGS_VOLUME_ELEMENT (0x0000)
#define MPI2_RAIDCONFIG0_EFLAGS_VOL_PHYS_DISK_ELEMENT (0x0001)
#define MPI2_RAIDCONFIG0_EFLAGS_HOT_SPARE_ELEMENT (0x0002)
#define MPI2_RAIDCONFIG0_EFLAGS_OCE_ELEMENT (0x0003)
typedef struct _MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U8 NumHotSpares; /*0x08 */
U8 NumPhysDisks; /*0x09 */
U8 NumVolumes; /*0x0A */
U8 ConfigNum; /*0x0B */
U32 Flags; /*0x0C */
U8 ConfigGUID[24]; /*0x10 */
U32 Reserved1; /*0x28 */
U8 NumElements; /*0x2C */
U8 Reserved2; /*0x2D */
U16 Reserved3; /*0x2E */
MPI2_RAIDCONFIG0_CONFIG_ELEMENT
ConfigElement[MPI2_RAIDCONFIG0_MAX_ELEMENTS]; /*0x30 */
} MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0,
*PTR_MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0,
Mpi2RaidConfigurationPage0_t,
*pMpi2RaidConfigurationPage0_t;
#define MPI2_RAIDCONFIG0_PAGEVERSION (0x00)
/*values for RAID Configuration Page 0 Flags field */
#define MPI2_RAIDCONFIG0_FLAG_FOREIGN_CONFIG (0x00000001)
/****************************************************************************
* Driver Persistent Mapping Config Pages
****************************************************************************/
/*Driver Persistent Mapping Page 0 */
typedef struct _MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY {
U64 PhysicalIdentifier; /*0x00 */
U16 MappingInformation; /*0x08 */
U16 DeviceIndex; /*0x0A */
U32 PhysicalBitsMapping; /*0x0C */
U32 Reserved1; /*0x10 */
} MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY,
*PTR_MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY,
Mpi2DriverMap0Entry_t, *pMpi2DriverMap0Entry_t;
typedef struct _MPI2_CONFIG_PAGE_DRIVER_MAPPING_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY Entry; /*0x08 */
} MPI2_CONFIG_PAGE_DRIVER_MAPPING_0,
*PTR_MPI2_CONFIG_PAGE_DRIVER_MAPPING_0,
Mpi2DriverMappingPage0_t, *pMpi2DriverMappingPage0_t;
#define MPI2_DRIVERMAPPING0_PAGEVERSION (0x00)
/*values for Driver Persistent Mapping Page 0 MappingInformation field */
#define MPI2_DRVMAP0_MAPINFO_SLOT_MASK (0x07F0)
#define MPI2_DRVMAP0_MAPINFO_SLOT_SHIFT (4)
#define MPI2_DRVMAP0_MAPINFO_MISSING_MASK (0x000F)
/****************************************************************************
* Ethernet Config Pages
****************************************************************************/
/*Ethernet Page 0 */
/*IP address (union of IPv4 and IPv6) */
typedef union _MPI2_ETHERNET_IP_ADDR {
U32 IPv4Addr;
U32 IPv6Addr[4];
} MPI2_ETHERNET_IP_ADDR, *PTR_MPI2_ETHERNET_IP_ADDR,
Mpi2EthernetIpAddr_t, *pMpi2EthernetIpAddr_t;
#define MPI2_ETHERNET_HOST_NAME_LENGTH (32)
typedef struct _MPI2_CONFIG_PAGE_ETHERNET_0 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /*0x00 */
U8 NumInterfaces; /*0x08 */
U8 Reserved0; /*0x09 */
U16 Reserved1; /*0x0A */
U32 Status; /*0x0C */
U8 MediaState; /*0x10 */
U8 Reserved2; /*0x11 */
U16 Reserved3; /*0x12 */
U8 MacAddress[6]; /*0x14 */
U8 Reserved4; /*0x1A */
U8 Reserved5; /*0x1B */
MPI2_ETHERNET_IP_ADDR IpAddress; /*0x1C */
MPI2_ETHERNET_IP_ADDR SubnetMask; /*0x2C */
MPI2_ETHERNET_IP_ADDR GatewayIpAddress;/*0x3C */
MPI2_ETHERNET_IP_ADDR DNS1IpAddress; /*0x4C */
MPI2_ETHERNET_IP_ADDR DNS2IpAddress; /*0x5C */
MPI2_ETHERNET_IP_ADDR DhcpIpAddress; /*0x6C */
U8
HostName[MPI2_ETHERNET_HOST_NAME_LENGTH];/*0x7C */
} MPI2_CONFIG_PAGE_ETHERNET_0,
*PTR_MPI2_CONFIG_PAGE_ETHERNET_0,
Mpi2EthernetPage0_t, *pMpi2EthernetPage0_t;
#define MPI2_ETHERNETPAGE0_PAGEVERSION (0x00)
/*values for Ethernet Page 0 Status field */
#define MPI2_ETHPG0_STATUS_IPV6_CAPABLE (0x80000000)
#define MPI2_ETHPG0_STATUS_IPV4_CAPABLE (0x40000000)
#define MPI2_ETHPG0_STATUS_CONSOLE_CONNECTED (0x20000000)
#define MPI2_ETHPG0_STATUS_DEFAULT_IF (0x00000100)
#define MPI2_ETHPG0_STATUS_FW_DWNLD_ENABLED (0x00000080)
#define MPI2_ETHPG0_STATUS_TELNET_ENABLED (0x00000040)
#define MPI2_ETHPG0_STATUS_SSH2_ENABLED (0x00000020)
#define MPI2_ETHPG0_STATUS_DHCP_CLIENT_ENABLED (0x00000010)
#define MPI2_ETHPG0_STATUS_IPV6_ENABLED (0x00000008)
#define MPI2_ETHPG0_STATUS_IPV4_ENABLED (0x00000004)
#define MPI2_ETHPG0_STATUS_IPV6_ADDRESSES (0x00000002)
#define MPI2_ETHPG0_STATUS_ETH_IF_ENABLED (0x00000001)
/*values for Ethernet Page 0 MediaState field */
#define MPI2_ETHPG0_MS_DUPLEX_MASK (0x80)
#define MPI2_ETHPG0_MS_HALF_DUPLEX (0x00)
#define MPI2_ETHPG0_MS_FULL_DUPLEX (0x80)
#define MPI2_ETHPG0_MS_CONNECT_SPEED_MASK (0x07)
#define MPI2_ETHPG0_MS_NOT_CONNECTED (0x00)
#define MPI2_ETHPG0_MS_10MBIT (0x01)
#define MPI2_ETHPG0_MS_100MBIT (0x02)
#define MPI2_ETHPG0_MS_1GBIT (0x03)
/*Ethernet Page 1 */
typedef struct _MPI2_CONFIG_PAGE_ETHERNET_1 {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
Reserved0; /*0x08 */
U32
Flags; /*0x0C */
U8
MediaState; /*0x10 */
U8
Reserved1; /*0x11 */
U16
Reserved2; /*0x12 */
U8
MacAddress[6]; /*0x14 */
U8
Reserved3; /*0x1A */
U8
Reserved4; /*0x1B */
MPI2_ETHERNET_IP_ADDR
StaticIpAddress; /*0x1C */
MPI2_ETHERNET_IP_ADDR
StaticSubnetMask; /*0x2C */
MPI2_ETHERNET_IP_ADDR
StaticGatewayIpAddress; /*0x3C */
MPI2_ETHERNET_IP_ADDR
StaticDNS1IpAddress; /*0x4C */
MPI2_ETHERNET_IP_ADDR
StaticDNS2IpAddress; /*0x5C */
U32
Reserved5; /*0x6C */
U32
Reserved6; /*0x70 */
U32
Reserved7; /*0x74 */
U32
Reserved8; /*0x78 */
U8
HostName[MPI2_ETHERNET_HOST_NAME_LENGTH];/*0x7C */
} MPI2_CONFIG_PAGE_ETHERNET_1,
*PTR_MPI2_CONFIG_PAGE_ETHERNET_1,
Mpi2EthernetPage1_t, *pMpi2EthernetPage1_t;
#define MPI2_ETHERNETPAGE1_PAGEVERSION (0x00)
/*values for Ethernet Page 1 Flags field */
#define MPI2_ETHPG1_FLAG_SET_DEFAULT_IF (0x00000100)
#define MPI2_ETHPG1_FLAG_ENABLE_FW_DOWNLOAD (0x00000080)
#define MPI2_ETHPG1_FLAG_ENABLE_TELNET (0x00000040)
#define MPI2_ETHPG1_FLAG_ENABLE_SSH2 (0x00000020)
#define MPI2_ETHPG1_FLAG_ENABLE_DHCP_CLIENT (0x00000010)
#define MPI2_ETHPG1_FLAG_ENABLE_IPV6 (0x00000008)
#define MPI2_ETHPG1_FLAG_ENABLE_IPV4 (0x00000004)
#define MPI2_ETHPG1_FLAG_USE_IPV6_ADDRESSES (0x00000002)
#define MPI2_ETHPG1_FLAG_ENABLE_ETH_IF (0x00000001)
/*values for Ethernet Page 1 MediaState field */
#define MPI2_ETHPG1_MS_DUPLEX_MASK (0x80)
#define MPI2_ETHPG1_MS_HALF_DUPLEX (0x00)
#define MPI2_ETHPG1_MS_FULL_DUPLEX (0x80)
#define MPI2_ETHPG1_MS_DATA_RATE_MASK (0x07)
#define MPI2_ETHPG1_MS_DATA_RATE_AUTO (0x00)
#define MPI2_ETHPG1_MS_DATA_RATE_10MBIT (0x01)
#define MPI2_ETHPG1_MS_DATA_RATE_100MBIT (0x02)
#define MPI2_ETHPG1_MS_DATA_RATE_1GBIT (0x03)
/****************************************************************************
* Extended Manufacturing Config Pages
****************************************************************************/
/*
*Generic structure to use for product-specific extended manufacturing pages
*(currently Extended Manufacturing Page 40 through Extended Manufacturing
*Page 60).
*/
typedef struct _MPI2_CONFIG_PAGE_EXT_MAN_PS {
MPI2_CONFIG_EXTENDED_PAGE_HEADER
Header; /*0x00 */
U32
ProductSpecificInfo; /*0x08 */
} MPI2_CONFIG_PAGE_EXT_MAN_PS,
*PTR_MPI2_CONFIG_PAGE_EXT_MAN_PS,
Mpi2ExtManufacturingPagePS_t,
*pMpi2ExtManufacturingPagePS_t;
/*PageVersion should be provided by product-specific code */
#endif
View Git Blame Copy Permalink