mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-29 15:43:59 +08:00
9ca1839776
Correct spelling typo in devicetree/bindings. Singed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
67 lines
2.0 KiB
Plaintext
67 lines
2.0 KiB
Plaintext
* DMA40 DMA Controller
|
|
|
|
Required properties:
|
|
- compatible: "stericsson,dma40"
|
|
- reg: Address range of the DMAC registers
|
|
- reg-names: Names of the above areas to use during resource look-up
|
|
- interrupt: Should contain the DMAC interrupt number
|
|
- #dma-cells: must be <3>
|
|
- memcpy-channels: Channels to be used for memcpy
|
|
|
|
Optional properties:
|
|
- dma-channels: Number of channels supported by hardware - if not present
|
|
the driver will attempt to obtain the information from H/W
|
|
- disabled-channels: Channels which can not be used
|
|
|
|
Example:
|
|
|
|
dma: dma-controller@801C0000 {
|
|
compatible = "stericsson,db8500-dma40", "stericsson,dma40";
|
|
reg = <0x801C0000 0x1000 0x40010000 0x800>;
|
|
reg-names = "base", "lcpa";
|
|
interrupt-parent = <&intc>;
|
|
interrupts = <0 25 0x4>;
|
|
|
|
#dma-cells = <2>;
|
|
memcpy-channels = <56 57 58 59 60>;
|
|
disabled-channels = <12>;
|
|
dma-channels = <8>;
|
|
};
|
|
|
|
Clients
|
|
Required properties:
|
|
- dmas: Comma separated list of dma channel requests
|
|
- dma-names: Names of the aforementioned requested channels
|
|
|
|
Each dmas request consists of 4 cells:
|
|
1. A phandle pointing to the DMA controller
|
|
2. Device Type
|
|
3. The DMA request line number (only when 'use fixed channel' is set)
|
|
4. A 32bit mask specifying; mode, direction and endianness [NB: This list will grow]
|
|
0x00000001: Mode:
|
|
Logical channel when unset
|
|
Physical channel when set
|
|
0x00000002: Direction:
|
|
Memory to Device when unset
|
|
Device to Memory when set
|
|
0x00000004: Endianness:
|
|
Little endian when unset
|
|
Big endian when set
|
|
0x00000008: Use fixed channel:
|
|
Use automatic channel selection when unset
|
|
Use DMA request line number when set
|
|
|
|
Example:
|
|
|
|
uart@80120000 {
|
|
compatible = "arm,pl011", "arm,primecell";
|
|
reg = <0x80120000 0x1000>;
|
|
interrupts = <0 11 0x4>;
|
|
|
|
dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */
|
|
<&dma 13 0 0x0>; /* Logical - MemToDev */
|
|
dma-names = "rx", "rx";
|
|
|
|
status = "disabled";
|
|
};
|