mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-24 21:24:00 +08:00
f18ac1a3d7
It's LDO2, not LD02. Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
164 lines
5.7 KiB
Plaintext
164 lines
5.7 KiB
Plaintext
* Samsung S5M8767 Voltage and Current Regulator
|
|
|
|
The Samsung S5M8767 is a multi-function device which includes voltage and
|
|
current regulators, rtc, charger controller and other sub-blocks. It is
|
|
interfaced to the host controller using a i2c interface. Each sub-block is
|
|
addressed by the host system using different i2c slave address. This document
|
|
describes the bindings for 'pmic' sub-block of s5m8767.
|
|
|
|
Required properties:
|
|
- compatible: Should be "samsung,s5m8767-pmic".
|
|
- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
|
|
|
|
- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
units for buck2 when changing voltage using gpio dvs. Refer to [1] below
|
|
for additional information.
|
|
|
|
- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
units for buck3 when changing voltage using gpio dvs. Refer to [1] below
|
|
for additional information.
|
|
|
|
- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
units for buck4 when changing voltage using gpio dvs. Refer to [1] below
|
|
for additional information.
|
|
|
|
- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
|
|
for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
|
|
|
|
[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
|
|
property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
|
|
property should specify atleast one voltage level (which would be a
|
|
safe operating voltage).
|
|
|
|
If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
|
|
property is specified, then all the eight voltage values for the
|
|
's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
|
|
|
|
Optional properties:
|
|
- interrupt-parent: Specifies the phandle of the interrupt controller to which
|
|
the interrupts from s5m8767 are delivered to.
|
|
- interrupts: Interrupt specifiers for two interrupt sources.
|
|
- First interrupt specifier is for 'irq1' interrupt.
|
|
- Second interrupt specifier is for 'alert' interrupt.
|
|
- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
|
|
- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
|
|
- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
|
|
|
|
Additional properties required if either of the optional properties are used:
|
|
|
|
- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
|
|
the possible 8 options selectable by the dvs gpios. The value of this
|
|
property should be between 0 and 7. If not specified or if out of range, the
|
|
default value of this property is set to 0.
|
|
|
|
- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
|
|
for dvs. The format of the gpio specifier depends in the gpio controller.
|
|
|
|
Regulators: The regulators of s5m8767 that have to be instantiated should be
|
|
included in a sub-node named 'regulators'. Regulator nodes included in this
|
|
sub-node should be of the format as listed below.
|
|
|
|
regulator_name {
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "VDD_ALIVE_1.0V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
op_mode = <1>; /* Normal Mode */
|
|
};
|
|
};
|
|
The above regulator entries are defined in regulator bindings documentation
|
|
except these properties:
|
|
- op_mode: describes the different operating modes of the LDO's with
|
|
power mode change in SOC. The different possible values are,
|
|
0 - always off mode
|
|
1 - on in normal mode
|
|
2 - low power mode
|
|
3 - suspend mode
|
|
- s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
|
|
GPIO controlling this regulator (enable/disable); This is
|
|
valid only for buck9.
|
|
|
|
The following are the names of the regulators that the s5m8767 pmic block
|
|
supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
|
|
as per the datasheet of s5m8767.
|
|
|
|
- LDOn
|
|
- valid values for n are 1 to 28
|
|
- Example: LDO1, LDO2, LDO28
|
|
- BUCKn
|
|
- valid values for n are 1 to 9.
|
|
- Example: BUCK1, BUCK2, BUCK9
|
|
|
|
The bindings inside the regulator nodes use the standard regulator bindings
|
|
which are documented elsewhere.
|
|
|
|
Example:
|
|
|
|
s5m8767_pmic@66 {
|
|
compatible = "samsung,s5m8767-pmic";
|
|
reg = <0x66>;
|
|
|
|
s5m8767,pmic-buck2-uses-gpio-dvs;
|
|
s5m8767,pmic-buck3-uses-gpio-dvs;
|
|
s5m8767,pmic-buck4-uses-gpio-dvs;
|
|
|
|
s5m8767,pmic-buck-default-dvs-idx = <0>;
|
|
|
|
s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
|
|
<&gpx0 1 0>, /* DVS2 */
|
|
<&gpx0 2 0>; /* DVS3 */
|
|
|
|
s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
|
|
<&gpx2 4 0>, /* SET2 */
|
|
<&gpx2 5 0>; /* SET3 */
|
|
|
|
s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
|
|
<1250000>, <1200000>,
|
|
<1150000>, <1100000>,
|
|
<1000000>, <950000>;
|
|
|
|
s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
|
|
<1100000>, <1100000>,
|
|
<1000000>, <1000000>,
|
|
<1000000>, <1000000>;
|
|
|
|
s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
|
|
<1200000>, <1200000>,
|
|
<1200000>, <1200000>,
|
|
<1200000>, <1200000>;
|
|
|
|
regulators {
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "VDD_ABB_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
op_mode = <1>; /* Normal Mode */
|
|
};
|
|
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "VDD_ALIVE_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "VDD_MIF_1.2V";
|
|
regulator-min-microvolt = <950000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vemmc_reg: BUCK9 {
|
|
regulator-name = "VMEM_VDD_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
op_mode = <3>; /* Standby Mode */
|
|
s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
|
|
};
|
|
};
|
|
};
|