renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-29 07:34:06 +08:00
Code
8b1d920fa5
linux-next/drivers/net/pcmcia/3c589_cs.c
Linus Torvalds f8965467f3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6 
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
2010-05-20 21:04:44 -07:00

980 lines
28 KiB
C
Raw Blame History

/*======================================================================
A PCMCIA ethernet driver for the 3com 3c589 card.
Copyright (C) 1999 David A. Hinds -- dahinds@users.sourceforge.net
3c589_cs.c 1.162 2001/10/13 00:08:50
The network driver code is based on Donald Becker's 3c589 code:
Written 1994 by Donald Becker.
Copyright 1993 United States Government as represented by the
Director, National Security Agency. This software may be used and
distributed according to the terms of the GNU General Public License,
incorporated herein by reference.
Donald Becker may be reached at becker@scyld.com
Updated for 2.5.x by Alan Cox <alan@lxorguk.ukuu.org.uk>
======================================================================*/
#define DRV_NAME "3c589_cs"
#define DRV_VERSION "1.162-ac"
#include <linux/module.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/ptrace.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/in.h>
#include <linux/delay.h>
#include <linux/ethtool.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
#include <linux/ioport.h>
#include <linux/bitops.h>
#include <linux/jiffies.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
#include <pcmcia/cistpl.h>
#include <pcmcia/cisreg.h>
#include <pcmcia/ciscode.h>
#include <pcmcia/ds.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/system.h>
/* To minimize the size of the driver source I only define operating
constants if they are used several times. You'll need the manual
if you want to understand driver details. */
/* Offsets from base I/O address. */
#define EL3_DATA 0x00
#define EL3_TIMER 0x0a
#define EL3_CMD 0x0e
#define EL3_STATUS 0x0e
#define EEPROM_READ 0x0080
#define EEPROM_BUSY 0x8000
#define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD)
/* The top five bits written to EL3_CMD are a command, the lower
11 bits are the parameter, if applicable. */
enum c509cmd {
TotalReset = 0<<11,
SelectWindow = 1<<11,
StartCoax = 2<<11,
RxDisable = 3<<11,
RxEnable = 4<<11,
RxReset = 5<<11,
RxDiscard = 8<<11,
TxEnable = 9<<11,
TxDisable = 10<<11,
TxReset = 11<<11,
FakeIntr = 12<<11,
AckIntr = 13<<11,
SetIntrEnb = 14<<11,
SetStatusEnb = 15<<11,
SetRxFilter = 16<<11,
SetRxThreshold = 17<<11,
SetTxThreshold = 18<<11,
SetTxStart = 19<<11,
StatsEnable = 21<<11,
StatsDisable = 22<<11,
StopCoax = 23<<11
};
enum c509status {
IntLatch = 0x0001,
AdapterFailure = 0x0002,
TxComplete = 0x0004,
TxAvailable = 0x0008,
RxComplete = 0x0010,
RxEarly = 0x0020,
IntReq = 0x0040,
StatsFull = 0x0080,
CmdBusy = 0x1000
};
/* The SetRxFilter command accepts the following classes: */
enum RxFilter {
RxStation = 1,
RxMulticast = 2,
RxBroadcast = 4,
RxProm = 8
};
/* Register window 1 offsets, the window used in normal operation. */
#define TX_FIFO 0x00
#define RX_FIFO 0x00
#define RX_STATUS 0x08
#define TX_STATUS 0x0B
#define TX_FREE 0x0C /* Remaining free bytes in Tx buffer. */
#define WN0_IRQ 0x08 /* Window 0: Set IRQ line in bits 12-15. */
#define WN4_MEDIA 0x0A /* Window 4: Various transcvr/media bits. */
#define MEDIA_TP 0x00C0 /* Enable link beat and jabber for 10baseT. */
#define MEDIA_LED 0x0001 /* Enable link light on 3C589E cards. */
/* Time in jiffies before concluding Tx hung */
#define TX_TIMEOUT ((400*HZ)/1000)
struct el3_private {
struct pcmcia_device *p_dev;
/* For transceiver monitoring */
struct timer_list media;
u16 media_status;
u16 fast_poll;
unsigned long last_irq;
spinlock_t lock;
};
static const char *if_names[] = { "auto", "10baseT", "10base2", "AUI" };
/*====================================================================*/
/* Module parameters */
MODULE_AUTHOR("David Hinds <dahinds@users.sourceforge.net>");
MODULE_DESCRIPTION("3Com 3c589 series PCMCIA ethernet driver");
MODULE_LICENSE("GPL");
#define INT_MODULE_PARM(n, v) static int n = v; module_param(n, int, 0)
/* Special hook for setting if_port when module is loaded */
INT_MODULE_PARM(if_port, 0);
/*====================================================================*/
static int tc589_config(struct pcmcia_device *link);
static void tc589_release(struct pcmcia_device *link);
static u16 read_eeprom(unsigned int ioaddr, int index);
static void tc589_reset(struct net_device *dev);
static void media_check(unsigned long arg);
static int el3_config(struct net_device *dev, struct ifmap *map);
static int el3_open(struct net_device *dev);
static netdev_tx_t el3_start_xmit(struct sk_buff *skb,
struct net_device *dev);
static irqreturn_t el3_interrupt(int irq, void *dev_id);
static void update_stats(struct net_device *dev);
static struct net_device_stats *el3_get_stats(struct net_device *dev);
static int el3_rx(struct net_device *dev);
static int el3_close(struct net_device *dev);
static void el3_tx_timeout(struct net_device *dev);
static void set_rx_mode(struct net_device *dev);
static void set_multicast_list(struct net_device *dev);
static const struct ethtool_ops netdev_ethtool_ops;
static void tc589_detach(struct pcmcia_device *p_dev);
/*======================================================================
tc589_attach() creates an "instance" of the driver, allocating
local data structures for one device. The device is registered
with Card Services.
======================================================================*/
static const struct net_device_ops el3_netdev_ops = {
.ndo_open = el3_open,
.ndo_stop = el3_close,
.ndo_start_xmit = el3_start_xmit,
.ndo_tx_timeout = el3_tx_timeout,
.ndo_set_config = el3_config,
.ndo_get_stats = el3_get_stats,
.ndo_set_multicast_list = set_multicast_list,
.ndo_change_mtu = eth_change_mtu,
.ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
};
static int tc589_probe(struct pcmcia_device *link)
{
struct el3_private *lp;
struct net_device *dev;
dev_dbg(&link->dev, "3c589_attach()\n");
/* Create new ethernet device */
dev = alloc_etherdev(sizeof(struct el3_private));
if (!dev)
return -ENOMEM;
lp = netdev_priv(dev);
link->priv = dev;
lp->p_dev = link;
spin_lock_init(&lp->lock);
link->io.NumPorts1 = 16;
link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
link->conf.ConfigIndex = 1;
dev->netdev_ops = &el3_netdev_ops;
dev->watchdog_timeo = TX_TIMEOUT;
SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
return tc589_config(link);
} /* tc589_attach */
/*======================================================================
This deletes a driver "instance". The device is de-registered
with Card Services. If it has been released, all local data
structures are freed. Otherwise, the structures will be freed
when the device is released.
======================================================================*/
static void tc589_detach(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
dev_dbg(&link->dev, "3c589_detach\n");
unregister_netdev(dev);
tc589_release(link);
free_netdev(dev);
} /* tc589_detach */
/*======================================================================
tc589_config() is scheduled to run after a CARD_INSERTION event
is received, to configure the PCMCIA socket, and to make the
ethernet device available to the system.
======================================================================*/
static int tc589_config(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
__be16 *phys_addr;
int ret, i, j, multi = 0, fifo;
unsigned int ioaddr;
char *ram_split[] = {"5:3", "3:1", "1:1", "3:5"};
u8 *buf;
size_t len;
dev_dbg(&link->dev, "3c589_config\n");
phys_addr = (__be16 *)dev->dev_addr;
/* Is this a 3c562? */
if (link->manf_id != MANFID_3COM)
printk(KERN_INFO "3c589_cs: hmmm, is this really a "
"3Com card??\n");
multi = (link->card_id == PRODID_3COM_3C562);
/* For the 3c562, the base address must be xx00-xx7f */
link->io.IOAddrLines = 16;
for (i = j = 0; j < 0x400; j += 0x10) {
if (multi && (j & 0x80)) continue;
link->io.BasePort1 = j ^ 0x300;
i = pcmcia_request_io(link, &link->io);
if (i == 0)
break;
}
if (i != 0)
goto failed;
ret = pcmcia_request_irq(link, el3_interrupt);
if (ret)
goto failed;
ret = pcmcia_request_configuration(link, &link->conf);
if (ret)
goto failed;
dev->irq = link->irq;
dev->base_addr = link->io.BasePort1;
ioaddr = dev->base_addr;
EL3WINDOW(0);
/* The 3c589 has an extra EEPROM for configuration info, including
the hardware address. The 3c562 puts the address in the CIS. */
len = pcmcia_get_tuple(link, 0x88, &buf);
if (buf && len >= 6) {
for (i = 0; i < 3; i++)
phys_addr[i] = htons(le16_to_cpu(buf[i*2]));
kfree(buf);
} else {
kfree(buf); /* 0 < len < 6 */
for (i = 0; i < 3; i++)
phys_addr[i] = htons(read_eeprom(ioaddr, i));
if (phys_addr[0] == htons(0x6060)) {
printk(KERN_ERR "3c589_cs: IO port conflict at 0x%03lx"
"-0x%03lx\n", dev->base_addr, dev->base_addr+15);
goto failed;
}
}
/* The address and resource configuration register aren't loaded from
the EEPROM and *must* be set to 0 and IRQ3 for the PCMCIA version. */
outw(0x3f00, ioaddr + 8);
fifo = inl(ioaddr);
/* The if_port symbol can be set when the module is loaded */
if ((if_port >= 0) && (if_port <= 3))
dev->if_port = if_port;
else
printk(KERN_ERR "3c589_cs: invalid if_port requested\n");
SET_NETDEV_DEV(dev, &link->dev);
if (register_netdev(dev) != 0) {
printk(KERN_ERR "3c589_cs: register_netdev() failed\n");
goto failed;
}
netdev_info(dev, "3Com 3c%s, io %#3lx, irq %d, hw_addr %pM\n",
(multi ? "562" : "589"), dev->base_addr, dev->irq,
dev->dev_addr);
netdev_info(dev, " %dK FIFO split %s Rx:Tx, %s xcvr\n",
(fifo & 7) ? 32 : 8, ram_split[(fifo >> 16) & 3],
if_names[dev->if_port]);
return 0;
failed:
tc589_release(link);
return -ENODEV;
} /* tc589_config */
/*======================================================================
After a card is removed, tc589_release() will unregister the net
device, and release the PCMCIA configuration. If the device is
still open, this will be postponed until it is closed.
======================================================================*/
static void tc589_release(struct pcmcia_device *link)
{
pcmcia_disable_device(link);
}
static int tc589_suspend(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
if (link->open)
netif_device_detach(dev);
return 0;
}
static int tc589_resume(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
if (link->open) {
tc589_reset(dev);
netif_device_attach(dev);
}
return 0;
}
/*====================================================================*/
/*
Use this for commands that may take time to finish
*/
static void tc589_wait_for_completion(struct net_device *dev, int cmd)
{
int i = 100;
outw(cmd, dev->base_addr + EL3_CMD);
while (--i > 0)
if (!(inw(dev->base_addr + EL3_STATUS) & 0x1000)) break;
if (i == 0)
netdev_warn(dev, "command 0x%04x did not complete!\n", cmd);
}
/*
Read a word from the EEPROM using the regular EEPROM access register.
Assume that we are in register window zero.
*/
static u16 read_eeprom(unsigned int ioaddr, int index)
{
int i;
outw(EEPROM_READ + index, ioaddr + 10);
/* Reading the eeprom takes 162 us */
for (i = 1620; i >= 0; i--)
if ((inw(ioaddr + 10) & EEPROM_BUSY) == 0)
break;
return inw(ioaddr + 12);
}
/*
Set transceiver type, perhaps to something other than what the user
specified in dev->if_port.
*/
static void tc589_set_xcvr(struct net_device *dev, int if_port)
{
struct el3_private *lp = netdev_priv(dev);
unsigned int ioaddr = dev->base_addr;
EL3WINDOW(0);
switch (if_port) {
case 0: case 1: outw(0, ioaddr + 6); break;
case 2: outw(3<<14, ioaddr + 6); break;
case 3: outw(1<<14, ioaddr + 6); break;
}
/* On PCMCIA, this just turns on the LED */
outw((if_port == 2) ? StartCoax : StopCoax, ioaddr + EL3_CMD);
/* 10baseT interface, enable link beat and jabber check. */
EL3WINDOW(4);
outw(MEDIA_LED | ((if_port < 2) ? MEDIA_TP : 0), ioaddr + WN4_MEDIA);
EL3WINDOW(1);
if (if_port == 2)
lp->media_status = ((dev->if_port == 0) ? 0x8000 : 0x4000);
else
lp->media_status = ((dev->if_port == 0) ? 0x4010 : 0x8800);
}
static void dump_status(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
EL3WINDOW(1);
netdev_info(dev, " irq status %04x, rx status %04x, tx status %02x tx free %04x\n",
inw(ioaddr+EL3_STATUS), inw(ioaddr+RX_STATUS),
inb(ioaddr+TX_STATUS), inw(ioaddr+TX_FREE));
EL3WINDOW(4);
netdev_info(dev, " diagnostics: fifo %04x net %04x ethernet %04x media %04x\n",
inw(ioaddr+0x04), inw(ioaddr+0x06), inw(ioaddr+0x08),
inw(ioaddr+0x0a));
EL3WINDOW(1);
}
/* Reset and restore all of the 3c589 registers. */
static void tc589_reset(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
int i;
EL3WINDOW(0);
outw(0x0001, ioaddr + 4); /* Activate board. */
outw(0x3f00, ioaddr + 8); /* Set the IRQ line. */
/* Set the station address in window 2. */
EL3WINDOW(2);
for (i = 0; i < 6; i++)
outb(dev->dev_addr[i], ioaddr + i);
tc589_set_xcvr(dev, dev->if_port);
/* Switch to the stats window, and clear all stats by reading. */
outw(StatsDisable, ioaddr + EL3_CMD);
EL3WINDOW(6);
for (i = 0; i < 9; i++)
inb(ioaddr+i);
inw(ioaddr + 10);
inw(ioaddr + 12);
/* Switch to register set 1 for normal use. */
EL3WINDOW(1);
set_rx_mode(dev);
outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */
outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */
/* Allow status bits to be seen. */
outw(SetStatusEnb | 0xff, ioaddr + EL3_CMD);
/* Ack all pending events, and set active indicator mask. */
outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq,
ioaddr + EL3_CMD);
outw(SetIntrEnb | IntLatch | TxAvailable | RxComplete | StatsFull
| AdapterFailure, ioaddr + EL3_CMD);
}
static void netdev_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
strcpy(info->driver, DRV_NAME);
strcpy(info->version, DRV_VERSION);
sprintf(info->bus_info, "PCMCIA 0x%lx", dev->base_addr);
}
static const struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
};
static int el3_config(struct net_device *dev, struct ifmap *map)
{
if ((map->port != (u_char)(-1)) && (map->port != dev->if_port)) {
if (map->port <= 3) {
dev->if_port = map->port;
netdev_info(dev, "switched to %s port\n", if_names[dev->if_port]);
tc589_set_xcvr(dev, dev->if_port);
} else
return -EINVAL;
}
return 0;
}
static int el3_open(struct net_device *dev)
{
struct el3_private *lp = netdev_priv(dev);
struct pcmcia_device *link = lp->p_dev;
if (!pcmcia_dev_present(link))
return -ENODEV;
link->open++;
netif_start_queue(dev);
tc589_reset(dev);
init_timer(&lp->media);
lp->media.function = &media_check;
lp->media.data = (unsigned long) dev;
lp->media.expires = jiffies + HZ;
add_timer(&lp->media);
dev_dbg(&link->dev, "%s: opened, status %4.4x.\n",
dev->name, inw(dev->base_addr + EL3_STATUS));
return 0;
}
static void el3_tx_timeout(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
netdev_warn(dev, "Transmit timed out!\n");
dump_status(dev);
dev->stats.tx_errors++;
dev->trans_start = jiffies; /* prevent tx timeout */
/* Issue TX_RESET and TX_START commands. */
tc589_wait_for_completion(dev, TxReset);
outw(TxEnable, ioaddr + EL3_CMD);
netif_wake_queue(dev);
}
static void pop_tx_status(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
int i;
/* Clear the Tx status stack. */
for (i = 32; i > 0; i--) {
u_char tx_status = inb(ioaddr + TX_STATUS);
if (!(tx_status & 0x84)) break;
/* reset transmitter on jabber error or underrun */
if (tx_status & 0x30)
tc589_wait_for_completion(dev, TxReset);
if (tx_status & 0x38) {
netdev_dbg(dev, "transmit error: status 0x%02x\n", tx_status);
outw(TxEnable, ioaddr + EL3_CMD);
dev->stats.tx_aborted_errors++;
}
outb(0x00, ioaddr + TX_STATUS); /* Pop the status stack. */
}
}
static netdev_tx_t el3_start_xmit(struct sk_buff *skb,
struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
struct el3_private *priv = netdev_priv(dev);
unsigned long flags;
netdev_dbg(dev, "el3_start_xmit(length = %ld) called, status %4.4x.\n",
(long)skb->len, inw(ioaddr + EL3_STATUS));
spin_lock_irqsave(&priv->lock, flags);
dev->stats.tx_bytes += skb->len;
/* Put out the doubleword header... */
outw(skb->len, ioaddr + TX_FIFO);
outw(0x00, ioaddr + TX_FIFO);
/* ... and the packet rounded to a doubleword. */
outsl(ioaddr + TX_FIFO, skb->data, (skb->len + 3) >> 2);
if (inw(ioaddr + TX_FREE) <= 1536) {
netif_stop_queue(dev);
/* Interrupt us when the FIFO has room for max-sized packet. */
outw(SetTxThreshold + 1536, ioaddr + EL3_CMD);
}
pop_tx_status(dev);
spin_unlock_irqrestore(&priv->lock, flags);
dev_kfree_skb(skb);
return NETDEV_TX_OK;
}
/* The EL3 interrupt handler. */
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
struct net_device *dev = (struct net_device *) dev_id;
struct el3_private *lp = netdev_priv(dev);
unsigned int ioaddr;
__u16 status;
int i = 0, handled = 1;
if (!netif_device_present(dev))
return IRQ_NONE;
ioaddr = dev->base_addr;
netdev_dbg(dev, "interrupt, status %4.4x.\n", inw(ioaddr + EL3_STATUS));
spin_lock(&lp->lock);
while ((status = inw(ioaddr + EL3_STATUS)) &
(IntLatch | RxComplete | StatsFull)) {
if ((status & 0xe000) != 0x2000) {
netdev_dbg(dev, "interrupt from dead card\n");
handled = 0;
break;
}
if (status & RxComplete)
el3_rx(dev);
if (status & TxAvailable) {
netdev_dbg(dev, " TX room bit was handled.\n");
/* There's room in the FIFO for a full-sized packet. */
outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
netif_wake_queue(dev);
}
if (status & TxComplete)
pop_tx_status(dev);
if (status & (AdapterFailure | RxEarly | StatsFull)) {
/* Handle all uncommon interrupts. */
if (status & StatsFull) /* Empty statistics. */
update_stats(dev);
if (status & RxEarly) { /* Rx early is unused. */
el3_rx(dev);
outw(AckIntr | RxEarly, ioaddr + EL3_CMD);
}
if (status & AdapterFailure) {
u16 fifo_diag;
EL3WINDOW(4);
fifo_diag = inw(ioaddr + 4);
EL3WINDOW(1);
netdev_warn(dev, "adapter failure, FIFO diagnostic register %04x.\n",
fifo_diag);
if (fifo_diag & 0x0400) {
/* Tx overrun */
tc589_wait_for_completion(dev, TxReset);
outw(TxEnable, ioaddr + EL3_CMD);
}
if (fifo_diag & 0x2000) {
/* Rx underrun */
tc589_wait_for_completion(dev, RxReset);
set_rx_mode(dev);
outw(RxEnable, ioaddr + EL3_CMD);
}
outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD);
}
}
if (++i > 10) {
netdev_err(dev, "infinite loop in interrupt, status %4.4x.\n",
status);
/* Clear all interrupts */
outw(AckIntr | 0xFF, ioaddr + EL3_CMD);
break;
}
/* Acknowledge the IRQ. */
outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD);
}
lp->last_irq = jiffies;
spin_unlock(&lp->lock);
netdev_dbg(dev, "exiting interrupt, status %4.4x.\n",
inw(ioaddr + EL3_STATUS));
return IRQ_RETVAL(handled);
}
static void media_check(unsigned long arg)
{
struct net_device *dev = (struct net_device *)(arg);
struct el3_private *lp = netdev_priv(dev);
unsigned int ioaddr = dev->base_addr;
u16 media, errs;
unsigned long flags;
if (!netif_device_present(dev)) goto reschedule;
/* Check for pending interrupt with expired latency timer: with
this, we can limp along even if the interrupt is blocked */
if ((inw(ioaddr + EL3_STATUS) & IntLatch) &&
(inb(ioaddr + EL3_TIMER) == 0xff)) {
if (!lp->fast_poll)
netdev_warn(dev, "interrupt(s) dropped!\n");
local_irq_save(flags);
el3_interrupt(dev->irq, dev);
local_irq_restore(flags);
lp->fast_poll = HZ;
}
if (lp->fast_poll) {
lp->fast_poll--;
lp->media.expires = jiffies + HZ/100;
add_timer(&lp->media);
return;
}
/* lp->lock guards the EL3 window. Window should always be 1 except
when the lock is held */
spin_lock_irqsave(&lp->lock, flags);
EL3WINDOW(4);
media = inw(ioaddr+WN4_MEDIA) & 0xc810;
/* Ignore collisions unless we've had no irq's recently */
if (time_before(jiffies, lp->last_irq + HZ)) {
media &= ~0x0010;
} else {
/* Try harder to detect carrier errors */
EL3WINDOW(6);
outw(StatsDisable, ioaddr + EL3_CMD);
errs = inb(ioaddr + 0);
outw(StatsEnable, ioaddr + EL3_CMD);
dev->stats.tx_carrier_errors += errs;
if (errs || (lp->media_status & 0x0010)) media |= 0x0010;
}
if (media != lp->media_status) {
if ((media & lp->media_status & 0x8000) &&
((lp->media_status ^ media) & 0x0800))
netdev_info(dev, "%s link beat\n",
(lp->media_status & 0x0800 ? "lost" : "found"));
else if ((media & lp->media_status & 0x4000) &&
((lp->media_status ^ media) & 0x0010))
netdev_info(dev, "coax cable %s\n",
(lp->media_status & 0x0010 ? "ok" : "problem"));
if (dev->if_port == 0) {
if (media & 0x8000) {
if (media & 0x0800)
netdev_info(dev, "flipped to 10baseT\n");
else
tc589_set_xcvr(dev, 2);
} else if (media & 0x4000) {
if (media & 0x0010)
tc589_set_xcvr(dev, 1);
else
netdev_info(dev, "flipped to 10base2\n");
}
}
lp->media_status = media;
}
EL3WINDOW(1);
spin_unlock_irqrestore(&lp->lock, flags);
reschedule:
lp->media.expires = jiffies + HZ;
add_timer(&lp->media);
}
static struct net_device_stats *el3_get_stats(struct net_device *dev)
{
struct el3_private *lp = netdev_priv(dev);
unsigned long flags;
struct pcmcia_device *link = lp->p_dev;
if (pcmcia_dev_present(link)) {
spin_lock_irqsave(&lp->lock, flags);
update_stats(dev);
spin_unlock_irqrestore(&lp->lock, flags);
}
return &dev->stats;
}
/*
Update statistics. We change to register window 6, so this should be run
single-threaded if the device is active. This is expected to be a rare
operation, and it's simpler for the rest of the driver to assume that
window 1 is always valid rather than use a special window-state variable.
Caller must hold the lock for this
*/
static void update_stats(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
netdev_dbg(dev, "updating the statistics.\n");
/* Turn off statistics updates while reading. */
outw(StatsDisable, ioaddr + EL3_CMD);
/* Switch to the stats window, and read everything. */
EL3WINDOW(6);
dev->stats.tx_carrier_errors += inb(ioaddr + 0);
dev->stats.tx_heartbeat_errors += inb(ioaddr + 1);
/* Multiple collisions. */ inb(ioaddr + 2);
dev->stats.collisions += inb(ioaddr + 3);
dev->stats.tx_window_errors += inb(ioaddr + 4);
dev->stats.rx_fifo_errors += inb(ioaddr + 5);
dev->stats.tx_packets += inb(ioaddr + 6);
/* Rx packets */ inb(ioaddr + 7);
/* Tx deferrals */ inb(ioaddr + 8);
/* Rx octets */ inw(ioaddr + 10);
/* Tx octets */ inw(ioaddr + 12);
/* Back to window 1, and turn statistics back on. */
EL3WINDOW(1);
outw(StatsEnable, ioaddr + EL3_CMD);
}
static int el3_rx(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
int worklimit = 32;
short rx_status;
netdev_dbg(dev, "in rx_packet(), status %4.4x, rx_status %4.4x.\n",
inw(ioaddr+EL3_STATUS), inw(ioaddr+RX_STATUS));
while (!((rx_status = inw(ioaddr + RX_STATUS)) & 0x8000) &&
worklimit > 0) {
worklimit--;
if (rx_status & 0x4000) { /* Error, update stats. */
short error = rx_status & 0x3800;
dev->stats.rx_errors++;
switch (error) {
case 0x0000: dev->stats.rx_over_errors++; break;
case 0x0800: dev->stats.rx_length_errors++; break;
case 0x1000: dev->stats.rx_frame_errors++; break;
case 0x1800: dev->stats.rx_length_errors++; break;
case 0x2000: dev->stats.rx_frame_errors++; break;
case 0x2800: dev->stats.rx_crc_errors++; break;
}
} else {
short pkt_len = rx_status & 0x7ff;
struct sk_buff *skb;
skb = dev_alloc_skb(pkt_len+5);
netdev_dbg(dev, " Receiving packet size %d status %4.4x.\n",
pkt_len, rx_status);
if (skb != NULL) {
skb_reserve(skb, 2);
insl(ioaddr+RX_FIFO, skb_put(skb, pkt_len),
(pkt_len+3)>>2);
skb->protocol = eth_type_trans(skb, dev);
netif_rx(skb);
dev->stats.rx_packets++;
dev->stats.rx_bytes += pkt_len;
} else {
netdev_dbg(dev, "couldn't allocate a sk_buff of size %d.\n",
pkt_len);
dev->stats.rx_dropped++;
}
}
/* Pop the top of the Rx FIFO */
tc589_wait_for_completion(dev, RxDiscard);
}
if (worklimit == 0)
netdev_warn(dev, "too much work in el3_rx!\n");
return 0;
}
static void set_rx_mode(struct net_device *dev)
{
unsigned int ioaddr = dev->base_addr;
u16 opts = SetRxFilter | RxStation | RxBroadcast;
if (dev->flags & IFF_PROMISC)
opts |= RxMulticast | RxProm;
else if (!netdev_mc_empty(dev) || (dev->flags & IFF_ALLMULTI))
opts |= RxMulticast;
outw(opts, ioaddr + EL3_CMD);
}
static void set_multicast_list(struct net_device *dev)
{
struct el3_private *priv = netdev_priv(dev);
unsigned long flags;
spin_lock_irqsave(&priv->lock, flags);
set_rx_mode(dev);
spin_unlock_irqrestore(&priv->lock, flags);
}
static int el3_close(struct net_device *dev)
{
struct el3_private *lp = netdev_priv(dev);
struct pcmcia_device *link = lp->p_dev;
unsigned int ioaddr = dev->base_addr;
dev_dbg(&link->dev, "%s: shutting down ethercard.\n", dev->name);
if (pcmcia_dev_present(link)) {
/* Turn off statistics ASAP. We update dev->stats below. */
outw(StatsDisable, ioaddr + EL3_CMD);
/* Disable the receiver and transmitter. */
outw(RxDisable, ioaddr + EL3_CMD);
outw(TxDisable, ioaddr + EL3_CMD);
if (dev->if_port == 2)
/* Turn off thinnet power. Green! */
outw(StopCoax, ioaddr + EL3_CMD);
else if (dev->if_port == 1) {
/* Disable link beat and jabber */
EL3WINDOW(4);
outw(0, ioaddr + WN4_MEDIA);
}
/* Switching back to window 0 disables the IRQ. */
EL3WINDOW(0);
/* But we explicitly zero the IRQ line select anyway. */
outw(0x0f00, ioaddr + WN0_IRQ);
/* Check if the card still exists */
if ((inw(ioaddr+EL3_STATUS) & 0xe000) == 0x2000)
update_stats(dev);
}
link->open--;
netif_stop_queue(dev);
del_timer_sync(&lp->media);
return 0;
}
static struct pcmcia_device_id tc589_ids[] = {
PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0101, 0x0562),
PCMCIA_MFC_DEVICE_PROD_ID1(0, "Motorola MARQUIS", 0xf03e4e77),
PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0589),
PCMCIA_DEVICE_PROD_ID12("Farallon", "ENet", 0x58d93fc4, 0x992c2202),
PCMCIA_MFC_DEVICE_CIS_MANF_CARD(0, 0x0101, 0x0035, "cis/3CXEM556.cis"),
PCMCIA_MFC_DEVICE_CIS_MANF_CARD(0, 0x0101, 0x003d, "cis/3CXEM556.cis"),
PCMCIA_DEVICE_NULL,
};
MODULE_DEVICE_TABLE(pcmcia, tc589_ids);
static struct pcmcia_driver tc589_driver = {
.owner = THIS_MODULE,
.drv = {
.name = "3c589_cs",
},
.probe = tc589_probe,
.remove = tc589_detach,
.id_table = tc589_ids,
.suspend = tc589_suspend,
.resume = tc589_resume,
};
static int __init init_tc589(void)
{
return pcmcia_register_driver(&tc589_driver);
}
static void __exit exit_tc589(void)
{
pcmcia_unregister_driver(&tc589_driver);
}
module_init(init_tc589);
module_exit(exit_tc589);
View Git Blame Copy Permalink