mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 20:53:53 +08:00
961a86d22e
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Signed-off-by: Joachim Eastwood <manabian@gmail.com>
128 lines
3.6 KiB
Plaintext
128 lines
3.6 KiB
Plaintext
* Device tree bindings for ARM PL172/PL175/PL176 MultiPort Memory Controller
|
|
|
|
Required properties:
|
|
|
|
- compatible: Must be "arm,primecell" and exactly one from
|
|
"arm,pl172", "arm,pl175" or "arm,pl176".
|
|
|
|
- reg: Must contains offset/length value for controller.
|
|
|
|
- #address-cells: Must be 2. The partition number has to be encoded in the
|
|
first address cell and it may accept values 0..N-1
|
|
(N - total number of partitions). The second cell is the
|
|
offset into the partition.
|
|
|
|
- #size-cells: Must be set to 1.
|
|
|
|
- ranges: Must contain one or more chip select memory regions.
|
|
|
|
- clocks: Must contain references to controller clocks.
|
|
|
|
- clock-names: Must contain "mpmcclk" and "apb_pclk".
|
|
|
|
- clock-ranges: Empty property indicating that child nodes can inherit
|
|
named clocks. Required only if clock tree data present
|
|
in device tree.
|
|
See clock-bindings.txt
|
|
|
|
Child chip-select (cs) nodes contain the memory devices nodes connected to
|
|
such as NOR (e.g. cfi-flash) and NAND.
|
|
|
|
Required child cs node properties:
|
|
|
|
- #address-cells: Must be 2.
|
|
|
|
- #size-cells: Must be 1.
|
|
|
|
- ranges: Empty property indicating that child nodes can inherit
|
|
memory layout.
|
|
|
|
- clock-ranges: Empty property indicating that child nodes can inherit
|
|
named clocks. Required only if clock tree data present
|
|
in device tree.
|
|
|
|
- mpmc,cs: Chip select number. Indicates to the pl0172 driver
|
|
which chipselect is used for accessing the memory.
|
|
|
|
- mpmc,memory-width: Width of the chip select memory. Must be equal to
|
|
either 8, 16 or 32.
|
|
|
|
Optional child cs node config properties:
|
|
|
|
- mpmc,async-page-mode: Enable asynchronous page mode.
|
|
|
|
- mpmc,cs-active-high: Set chip select polarity to active high.
|
|
|
|
- mpmc,byte-lane-low: Set byte lane state to low.
|
|
|
|
- mpmc,extended-wait: Enable extended wait.
|
|
|
|
- mpmc,buffer-enable: Enable write buffer, option is not supported by
|
|
PL175 and PL176 controllers.
|
|
|
|
- mpmc,write-protect: Enable write protect.
|
|
|
|
Optional child cs node timing properties:
|
|
|
|
- mpmc,write-enable-delay: Delay from chip select assertion to write
|
|
enable (WE signal) in nano seconds.
|
|
|
|
- mpmc,output-enable-delay: Delay from chip select assertion to output
|
|
enable (OE signal) in nano seconds.
|
|
|
|
- mpmc,write-access-delay: Delay from chip select assertion to write
|
|
access in nano seconds.
|
|
|
|
- mpmc,read-access-delay: Delay from chip select assertion to read
|
|
access in nano seconds.
|
|
|
|
- mpmc,page-mode-read-delay: Delay for asynchronous page mode sequential
|
|
accesses in nano seconds.
|
|
|
|
- mpmc,turn-round-delay: Delay between access to memory banks in nano
|
|
seconds.
|
|
|
|
If any of the above timing parameters are absent, current parameter value will
|
|
be taken from the corresponding HW reg.
|
|
|
|
Example for pl172 with nor flash on chip select 0 shown below.
|
|
|
|
emc: memory-controller@40005000 {
|
|
compatible = "arm,pl172", "arm,primecell";
|
|
reg = <0x40005000 0x1000>;
|
|
clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
|
|
clock-names = "mpmcclk", "apb_pclk";
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0 0x1c000000 0x1000000
|
|
1 0 0x1d000000 0x1000000
|
|
2 0 0x1e000000 0x1000000
|
|
3 0 0x1f000000 0x1000000>;
|
|
|
|
cs0 {
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
mpmc,cs = <0>;
|
|
mpmc,memory-width = <16>;
|
|
mpmc,byte-lane-low;
|
|
mpmc,write-enable-delay = <0>;
|
|
mpmc,output-enable-delay = <0>;
|
|
mpmc,read-enable-delay = <70>;
|
|
mpmc,page-mode-read-delay = <70>;
|
|
|
|
flash@0,0 {
|
|
compatible = "sst,sst39vf320", "cfi-flash";
|
|
reg = <0 0 0x400000>;
|
|
bank-width = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
partition@0 {
|
|
label = "data";
|
|
reg = <0 0x400000>;
|
|
};
|
|
};
|
|
};
|
|
};
|