mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-25 05:34:00 +08:00
597 lines
14 KiB
C
597 lines
14 KiB
C
/*
|
|
* linux/arch/arm/mach-omap2/board-omap3beagle.c
|
|
*
|
|
* Copyright (C) 2008 Texas Instruments
|
|
*
|
|
* Modified from mach-omap2/board-3430sdp.c
|
|
*
|
|
* Initial code: Syed Mohammed Khasim
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/err.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/input.h>
|
|
#include <linux/gpio_keys.h>
|
|
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mmc/host.h>
|
|
|
|
#include <linux/regulator/machine.h>
|
|
#include <linux/i2c/twl.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/flash.h>
|
|
|
|
#include <plat/board.h>
|
|
#include <plat/common.h>
|
|
#include <plat/display.h>
|
|
#include <plat/gpmc.h>
|
|
#include <plat/nand.h>
|
|
#include <plat/usb.h>
|
|
#include <plat/timer-gp.h>
|
|
|
|
#include "mux.h"
|
|
#include "hsmmc.h"
|
|
|
|
#define NAND_BLOCK_SIZE SZ_128K
|
|
|
|
/*
|
|
* OMAP3 Beagle revision
|
|
* Run time detection of Beagle revision is done by reading GPIO.
|
|
* GPIO ID -
|
|
* AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
|
|
* C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
|
|
* C4 = GPIO173, GPIO172, GPIO171: 1 0 1
|
|
* XM = GPIO173, GPIO172, GPIO171: 0 0 0
|
|
*/
|
|
enum {
|
|
OMAP3BEAGLE_BOARD_UNKN = 0,
|
|
OMAP3BEAGLE_BOARD_AXBX,
|
|
OMAP3BEAGLE_BOARD_C1_3,
|
|
OMAP3BEAGLE_BOARD_C4,
|
|
OMAP3BEAGLE_BOARD_XM,
|
|
};
|
|
|
|
static u8 omap3_beagle_version;
|
|
|
|
static u8 omap3_beagle_get_rev(void)
|
|
{
|
|
return omap3_beagle_version;
|
|
}
|
|
|
|
static void __init omap3_beagle_init_rev(void)
|
|
{
|
|
int ret;
|
|
u16 beagle_rev = 0;
|
|
|
|
omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
|
|
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
|
|
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
|
|
|
|
ret = gpio_request(171, "rev_id_0");
|
|
if (ret < 0)
|
|
goto fail0;
|
|
|
|
ret = gpio_request(172, "rev_id_1");
|
|
if (ret < 0)
|
|
goto fail1;
|
|
|
|
ret = gpio_request(173, "rev_id_2");
|
|
if (ret < 0)
|
|
goto fail2;
|
|
|
|
gpio_direction_input(171);
|
|
gpio_direction_input(172);
|
|
gpio_direction_input(173);
|
|
|
|
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
|
|
| (gpio_get_value(173) << 2);
|
|
|
|
switch (beagle_rev) {
|
|
case 7:
|
|
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
|
|
break;
|
|
case 6:
|
|
printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
|
|
break;
|
|
case 5:
|
|
printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
|
|
break;
|
|
case 0:
|
|
printk(KERN_INFO "OMAP3 Beagle Rev: xM\n");
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
|
|
break;
|
|
default:
|
|
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
|
|
}
|
|
|
|
return;
|
|
|
|
fail2:
|
|
gpio_free(172);
|
|
fail1:
|
|
gpio_free(171);
|
|
fail0:
|
|
printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
|
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
|
|
|
|
return;
|
|
}
|
|
|
|
static struct mtd_partition omap3beagle_nand_partitions[] = {
|
|
/* All the partition sizes are listed in terms of NAND block size */
|
|
{
|
|
.name = "X-Loader",
|
|
.offset = 0,
|
|
.size = 4 * NAND_BLOCK_SIZE,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "U-Boot",
|
|
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
|
|
.size = 15 * NAND_BLOCK_SIZE,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "U-Boot Env",
|
|
.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
|
|
.size = 1 * NAND_BLOCK_SIZE,
|
|
},
|
|
{
|
|
.name = "Kernel",
|
|
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
|
|
.size = 32 * NAND_BLOCK_SIZE,
|
|
},
|
|
{
|
|
.name = "File System",
|
|
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
static struct omap_nand_platform_data omap3beagle_nand_data = {
|
|
.options = NAND_BUSWIDTH_16,
|
|
.parts = omap3beagle_nand_partitions,
|
|
.nr_parts = ARRAY_SIZE(omap3beagle_nand_partitions),
|
|
.dma_channel = -1, /* disable DMA in OMAP NAND driver */
|
|
.nand_setup = NULL,
|
|
.dev_ready = NULL,
|
|
};
|
|
|
|
/* DSS */
|
|
|
|
static int beagle_enable_dvi(struct omap_dss_device *dssdev)
|
|
{
|
|
if (gpio_is_valid(dssdev->reset_gpio))
|
|
gpio_set_value(dssdev->reset_gpio, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void beagle_disable_dvi(struct omap_dss_device *dssdev)
|
|
{
|
|
if (gpio_is_valid(dssdev->reset_gpio))
|
|
gpio_set_value(dssdev->reset_gpio, 0);
|
|
}
|
|
|
|
static struct omap_dss_device beagle_dvi_device = {
|
|
.type = OMAP_DISPLAY_TYPE_DPI,
|
|
.name = "dvi",
|
|
.driver_name = "generic_panel",
|
|
.phy.dpi.data_lines = 24,
|
|
.reset_gpio = 170,
|
|
.platform_enable = beagle_enable_dvi,
|
|
.platform_disable = beagle_disable_dvi,
|
|
};
|
|
|
|
static struct omap_dss_device beagle_tv_device = {
|
|
.name = "tv",
|
|
.driver_name = "venc",
|
|
.type = OMAP_DISPLAY_TYPE_VENC,
|
|
.phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
|
|
};
|
|
|
|
static struct omap_dss_device *beagle_dss_devices[] = {
|
|
&beagle_dvi_device,
|
|
&beagle_tv_device,
|
|
};
|
|
|
|
static struct omap_dss_board_info beagle_dss_data = {
|
|
.num_devices = ARRAY_SIZE(beagle_dss_devices),
|
|
.devices = beagle_dss_devices,
|
|
.default_device = &beagle_dvi_device,
|
|
};
|
|
|
|
static struct platform_device beagle_dss_device = {
|
|
.name = "omapdss",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &beagle_dss_data,
|
|
},
|
|
};
|
|
|
|
static struct regulator_consumer_supply beagle_vdac_supply =
|
|
REGULATOR_SUPPLY("vdda_dac", "omapdss");
|
|
|
|
static struct regulator_consumer_supply beagle_vdvi_supply =
|
|
REGULATOR_SUPPLY("vdds_dsi", "omapdss");
|
|
|
|
static void __init beagle_display_init(void)
|
|
{
|
|
int r;
|
|
|
|
r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
|
|
if (r < 0) {
|
|
printk(KERN_ERR "Unable to get DVI reset GPIO\n");
|
|
return;
|
|
}
|
|
|
|
gpio_direction_output(beagle_dvi_device.reset_gpio, 0);
|
|
}
|
|
|
|
#include "sdram-micron-mt46h32m32lf-6.h"
|
|
|
|
static struct omap2_hsmmc_info mmc[] = {
|
|
{
|
|
.mmc = 1,
|
|
.caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
|
|
.gpio_wp = 29,
|
|
},
|
|
{} /* Terminator */
|
|
};
|
|
|
|
static struct regulator_consumer_supply beagle_vmmc1_supply = {
|
|
.supply = "vmmc",
|
|
};
|
|
|
|
static struct regulator_consumer_supply beagle_vsim_supply = {
|
|
.supply = "vmmc_aux",
|
|
};
|
|
|
|
static struct gpio_led gpio_leds[];
|
|
|
|
static int beagle_twl_gpio_setup(struct device *dev,
|
|
unsigned gpio, unsigned ngpio)
|
|
{
|
|
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
|
|
mmc[0].gpio_wp = -EINVAL;
|
|
} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
|
|
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
|
|
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
|
|
mmc[0].gpio_wp = 23;
|
|
} else {
|
|
omap_mux_init_gpio(29, OMAP_PIN_INPUT);
|
|
}
|
|
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
|
|
mmc[0].gpio_cd = gpio + 0;
|
|
omap2_hsmmc_init(mmc);
|
|
|
|
/* link regulators to MMC adapters */
|
|
beagle_vmmc1_supply.dev = mmc[0].dev;
|
|
beagle_vsim_supply.dev = mmc[0].dev;
|
|
|
|
/* REVISIT: need ehci-omap hooks for external VBUS
|
|
* power switch and overcurrent detect
|
|
*/
|
|
|
|
gpio_request(gpio + 1, "EHCI_nOC");
|
|
gpio_direction_input(gpio + 1);
|
|
|
|
/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
|
|
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
|
|
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
|
|
|
|
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
|
|
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct twl4030_gpio_platform_data beagle_gpio_data = {
|
|
.gpio_base = OMAP_MAX_GPIO_LINES,
|
|
.irq_base = TWL4030_GPIO_IRQ_BASE,
|
|
.irq_end = TWL4030_GPIO_IRQ_END,
|
|
.use_leds = true,
|
|
.pullups = BIT(1),
|
|
.pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
|
|
| BIT(15) | BIT(16) | BIT(17),
|
|
.setup = beagle_twl_gpio_setup,
|
|
};
|
|
|
|
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
|
|
static struct regulator_init_data beagle_vmmc1 = {
|
|
.constraints = {
|
|
.min_uV = 1850000,
|
|
.max_uV = 3150000,
|
|
.valid_modes_mask = REGULATOR_MODE_NORMAL
|
|
| REGULATOR_MODE_STANDBY,
|
|
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
|
|
| REGULATOR_CHANGE_MODE
|
|
| REGULATOR_CHANGE_STATUS,
|
|
},
|
|
.num_consumer_supplies = 1,
|
|
.consumer_supplies = &beagle_vmmc1_supply,
|
|
};
|
|
|
|
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
|
|
static struct regulator_init_data beagle_vsim = {
|
|
.constraints = {
|
|
.min_uV = 1800000,
|
|
.max_uV = 3000000,
|
|
.valid_modes_mask = REGULATOR_MODE_NORMAL
|
|
| REGULATOR_MODE_STANDBY,
|
|
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
|
|
| REGULATOR_CHANGE_MODE
|
|
| REGULATOR_CHANGE_STATUS,
|
|
},
|
|
.num_consumer_supplies = 1,
|
|
.consumer_supplies = &beagle_vsim_supply,
|
|
};
|
|
|
|
/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
|
|
static struct regulator_init_data beagle_vdac = {
|
|
.constraints = {
|
|
.min_uV = 1800000,
|
|
.max_uV = 1800000,
|
|
.valid_modes_mask = REGULATOR_MODE_NORMAL
|
|
| REGULATOR_MODE_STANDBY,
|
|
.valid_ops_mask = REGULATOR_CHANGE_MODE
|
|
| REGULATOR_CHANGE_STATUS,
|
|
},
|
|
.num_consumer_supplies = 1,
|
|
.consumer_supplies = &beagle_vdac_supply,
|
|
};
|
|
|
|
/* VPLL2 for digital video outputs */
|
|
static struct regulator_init_data beagle_vpll2 = {
|
|
.constraints = {
|
|
.name = "VDVI",
|
|
.min_uV = 1800000,
|
|
.max_uV = 1800000,
|
|
.valid_modes_mask = REGULATOR_MODE_NORMAL
|
|
| REGULATOR_MODE_STANDBY,
|
|
.valid_ops_mask = REGULATOR_CHANGE_MODE
|
|
| REGULATOR_CHANGE_STATUS,
|
|
},
|
|
.num_consumer_supplies = 1,
|
|
.consumer_supplies = &beagle_vdvi_supply,
|
|
};
|
|
|
|
static struct twl4030_usb_data beagle_usb_data = {
|
|
.usb_mode = T2_USB_MODE_ULPI,
|
|
};
|
|
|
|
static struct twl4030_codec_audio_data beagle_audio_data = {
|
|
.audio_mclk = 26000000,
|
|
};
|
|
|
|
static struct twl4030_codec_data beagle_codec_data = {
|
|
.audio_mclk = 26000000,
|
|
.audio = &beagle_audio_data,
|
|
};
|
|
|
|
static struct twl4030_platform_data beagle_twldata = {
|
|
.irq_base = TWL4030_IRQ_BASE,
|
|
.irq_end = TWL4030_IRQ_END,
|
|
|
|
/* platform_data for children goes here */
|
|
.usb = &beagle_usb_data,
|
|
.gpio = &beagle_gpio_data,
|
|
.codec = &beagle_codec_data,
|
|
.vmmc1 = &beagle_vmmc1,
|
|
.vsim = &beagle_vsim,
|
|
.vdac = &beagle_vdac,
|
|
.vpll2 = &beagle_vpll2,
|
|
};
|
|
|
|
static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
|
|
{
|
|
I2C_BOARD_INFO("twl4030", 0x48),
|
|
.flags = I2C_CLIENT_WAKE,
|
|
.irq = INT_34XX_SYS_NIRQ,
|
|
.platform_data = &beagle_twldata,
|
|
},
|
|
};
|
|
|
|
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
|
|
{
|
|
I2C_BOARD_INFO("eeprom", 0x50),
|
|
},
|
|
};
|
|
|
|
static int __init omap3_beagle_i2c_init(void)
|
|
{
|
|
omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
|
|
ARRAY_SIZE(beagle_i2c_boardinfo));
|
|
/* Bus 3 is attached to the DVI port where devices like the pico DLP
|
|
* projector don't work reliably with 400kHz */
|
|
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
|
|
return 0;
|
|
}
|
|
|
|
static struct gpio_led gpio_leds[] = {
|
|
{
|
|
.name = "beagleboard::usr0",
|
|
.default_trigger = "heartbeat",
|
|
.gpio = 150,
|
|
},
|
|
{
|
|
.name = "beagleboard::usr1",
|
|
.default_trigger = "mmc0",
|
|
.gpio = 149,
|
|
},
|
|
{
|
|
.name = "beagleboard::pmu_stat",
|
|
.gpio = -EINVAL, /* gets replaced */
|
|
.active_low = true,
|
|
},
|
|
};
|
|
|
|
static struct gpio_led_platform_data gpio_led_info = {
|
|
.leds = gpio_leds,
|
|
.num_leds = ARRAY_SIZE(gpio_leds),
|
|
};
|
|
|
|
static struct platform_device leds_gpio = {
|
|
.name = "leds-gpio",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &gpio_led_info,
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_button gpio_buttons[] = {
|
|
{
|
|
.code = BTN_EXTRA,
|
|
.gpio = 7,
|
|
.desc = "user",
|
|
.wakeup = 1,
|
|
},
|
|
};
|
|
|
|
static struct gpio_keys_platform_data gpio_key_info = {
|
|
.buttons = gpio_buttons,
|
|
.nbuttons = ARRAY_SIZE(gpio_buttons),
|
|
};
|
|
|
|
static struct platform_device keys_gpio = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &gpio_key_info,
|
|
},
|
|
};
|
|
|
|
static void __init omap3_beagle_init_irq(void)
|
|
{
|
|
omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
|
|
mt46h32m32lf6_sdrc_params);
|
|
omap_init_irq();
|
|
#ifdef CONFIG_OMAP_32K_TIMER
|
|
omap2_gp_clockevent_set_gptimer(12);
|
|
#endif
|
|
omap_gpio_init();
|
|
}
|
|
|
|
static struct platform_device *omap3_beagle_devices[] __initdata = {
|
|
&leds_gpio,
|
|
&keys_gpio,
|
|
&beagle_dss_device,
|
|
};
|
|
|
|
static void __init omap3beagle_flash_init(void)
|
|
{
|
|
u8 cs = 0;
|
|
u8 nandcs = GPMC_CS_NUM + 1;
|
|
|
|
/* find out the chip-select on which NAND exists */
|
|
while (cs < GPMC_CS_NUM) {
|
|
u32 ret = 0;
|
|
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
|
|
|
|
if ((ret & 0xC00) == 0x800) {
|
|
printk(KERN_INFO "Found NAND on CS%d\n", cs);
|
|
if (nandcs > GPMC_CS_NUM)
|
|
nandcs = cs;
|
|
}
|
|
cs++;
|
|
}
|
|
|
|
if (nandcs > GPMC_CS_NUM) {
|
|
printk(KERN_INFO "NAND: Unable to find configuration "
|
|
"in GPMC\n ");
|
|
return;
|
|
}
|
|
|
|
if (nandcs < GPMC_CS_NUM) {
|
|
omap3beagle_nand_data.cs = nandcs;
|
|
|
|
printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
|
|
if (gpmc_nand_init(&omap3beagle_nand_data) < 0)
|
|
printk(KERN_ERR "Unable to register NAND device\n");
|
|
}
|
|
}
|
|
|
|
static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
|
|
|
|
.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
|
|
.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
|
|
.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
|
|
|
|
.phy_reset = true,
|
|
.reset_gpio_port[0] = -EINVAL,
|
|
.reset_gpio_port[1] = 147,
|
|
.reset_gpio_port[2] = -EINVAL
|
|
};
|
|
|
|
#ifdef CONFIG_OMAP_MUX
|
|
static struct omap_board_mux board_mux[] __initdata = {
|
|
{ .reg_offset = OMAP_MUX_TERMINATOR },
|
|
};
|
|
#else
|
|
#define board_mux NULL
|
|
#endif
|
|
|
|
static struct omap_musb_board_data musb_board_data = {
|
|
.interface_type = MUSB_INTERFACE_ULPI,
|
|
.mode = MUSB_OTG,
|
|
.power = 100,
|
|
};
|
|
|
|
static void __init omap3_beagle_init(void)
|
|
{
|
|
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
|
|
omap3_beagle_init_rev();
|
|
omap3_beagle_i2c_init();
|
|
platform_add_devices(omap3_beagle_devices,
|
|
ARRAY_SIZE(omap3_beagle_devices));
|
|
omap_serial_init();
|
|
|
|
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
|
|
gpio_request(170, "DVI_nPD");
|
|
/* REVISIT leave DVI powered down until it's needed ... */
|
|
gpio_direction_output(170, true);
|
|
|
|
usb_musb_init(&musb_board_data);
|
|
usb_ehci_init(&ehci_pdata);
|
|
omap3beagle_flash_init();
|
|
|
|
/* Ensure SDRC pins are mux'd for self-refresh */
|
|
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
|
|
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
|
|
|
|
beagle_display_init();
|
|
}
|
|
|
|
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
|
|
/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
|
|
.phys_io = 0x48000000,
|
|
.io_pg_offst = ((0xfa000000) >> 18) & 0xfffc,
|
|
.boot_params = 0x80000100,
|
|
.map_io = omap3_map_io,
|
|
.reserve = omap_reserve,
|
|
.init_irq = omap3_beagle_init_irq,
|
|
.init_machine = omap3_beagle_init,
|
|
.timer = &omap_timer,
|
|
MACHINE_END
|