renegade-project/linux-next
2
0
Fork 0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-22 20:23:57 +08:00
Code
7923811a46
linux-next/drivers/usb/gadget/omap_udc.h
David Brownell 65111084c6 [PATCH] USB: more omap_udc updates (dma and omap1710) 
More omap_udc updates:

  * OMAP 1710 updates
      - new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT
      - new OTG bits affecting wakeup
  * Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in
    for under 1024 bytes (not "up to 1024 bytes")
  * Handle transceiver setup more intelligently
      - use transceiver whenever one's available; this can be handy
        for GPIO based, loopback, or transceiverless configs
      - cleanup correctly after the "unrecognized HMC" case
  * DMA performance tweaks
      - allow burst/pack for memory access
      - use 16 bit DMA access most of the time on TIPB
  * Add workarounds for some DMA errata (not observed "in the wild"):
      - DMA CSAC/CDAC reads returning zero
      - RX/TX DMA config registers bit 12 always reads as zero (TI patch)
  * More "sparse" warnings removed, notably "changing" the SETUP packet
    to return data in USB byteorder (an API change, null effect on OMAP
    except for these warnings).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27 14:43:50 -07:00

211 lines
6.6 KiB
C
Raw Blame History

/*
* omap_udc.h -- for omap 3.2 udc, with OTG support
*
* 2004 (C) Texas Instruments, Inc.
* 2004 (C) David Brownell
*/
/*
* USB device/endpoint management registers
*/
#define UDC_REG(offset) __REG16(UDC_BASE + (offset))
#define UDC_REV_REG UDC_REG(0x0) /* Revision */
#define UDC_EP_NUM_REG UDC_REG(0x4) /* Which endpoint */
# define UDC_SETUP_SEL (1 << 6)
# define UDC_EP_SEL (1 << 5)
# define UDC_EP_DIR (1 << 4)
/* low 4 bits for endpoint number */
#define UDC_DATA_REG UDC_REG(0x08) /* Endpoint FIFO */
#define UDC_CTRL_REG UDC_REG(0x0C) /* Endpoint control */
# define UDC_CLR_HALT (1 << 7)
# define UDC_SET_HALT (1 << 6)
# define UDC_CLRDATA_TOGGLE (1 << 3)
# define UDC_SET_FIFO_EN (1 << 2)
# define UDC_CLR_EP (1 << 1)
# define UDC_RESET_EP (1 << 0)
#define UDC_STAT_FLG_REG UDC_REG(0x10) /* Endpoint status */
# define UDC_NO_RXPACKET (1 << 15)
# define UDC_MISS_IN (1 << 14)
# define UDC_DATA_FLUSH (1 << 13)
# define UDC_ISO_ERR (1 << 12)
# define UDC_ISO_FIFO_EMPTY (1 << 9)
# define UDC_ISO_FIFO_FULL (1 << 8)
# define UDC_EP_HALTED (1 << 6)
# define UDC_STALL (1 << 5)
# define UDC_NAK (1 << 4)
# define UDC_ACK (1 << 3)
# define UDC_FIFO_EN (1 << 2)
# define UDC_NON_ISO_FIFO_EMPTY (1 << 1)
# define UDC_NON_ISO_FIFO_FULL (1 << 0)
#define UDC_RXFSTAT_REG UDC_REG(0x14) /* OUT bytecount */
#define UDC_SYSCON1_REG UDC_REG(0x18) /* System config 1 */
# define UDC_CFG_LOCK (1 << 8)
# define UDC_DATA_ENDIAN (1 << 7)
# define UDC_DMA_ENDIAN (1 << 6)
# define UDC_NAK_EN (1 << 4)
# define UDC_AUTODECODE_DIS (1 << 3)
# define UDC_SELF_PWR (1 << 2)
# define UDC_SOFF_DIS (1 << 1)
# define UDC_PULLUP_EN (1 << 0)
#define UDC_SYSCON2_REG UDC_REG(0x1C) /* System config 2 */
# define UDC_RMT_WKP (1 << 6)
# define UDC_STALL_CMD (1 << 5)
# define UDC_DEV_CFG (1 << 3)
# define UDC_CLR_CFG (1 << 2)
#define UDC_DEVSTAT_REG UDC_REG(0x20) /* Device status */
# define UDC_B_HNP_ENABLE (1 << 9)
# define UDC_A_HNP_SUPPORT (1 << 8)
# define UDC_A_ALT_HNP_SUPPORT (1 << 7)
# define UDC_R_WK_OK (1 << 6)
# define UDC_USB_RESET (1 << 5)
# define UDC_SUS (1 << 4)
# define UDC_CFG (1 << 3)
# define UDC_ADD (1 << 2)
# define UDC_DEF (1 << 1)
# define UDC_ATT (1 << 0)
#define UDC_SOF_REG UDC_REG(0x24) /* Start of frame */
# define UDC_FT_LOCK (1 << 12)
# define UDC_TS_OK (1 << 11)
# define UDC_TS 0x03ff
#define UDC_IRQ_EN_REG UDC_REG(0x28) /* Interrupt enable */
# define UDC_SOF_IE (1 << 7)
# define UDC_EPN_RX_IE (1 << 5)
# define UDC_EPN_TX_IE (1 << 4)
# define UDC_DS_CHG_IE (1 << 3)
# define UDC_EP0_IE (1 << 0)
#define UDC_DMA_IRQ_EN_REG UDC_REG(0x2C) /* DMA irq enable */
/* rx/tx dma channels numbered 1-3 not 0-2 */
# define UDC_TX_DONE_IE(n) (1 << (4 * (n) - 2))
# define UDC_RX_CNT_IE(n) (1 << (4 * (n) - 3))
# define UDC_RX_EOT_IE(n) (1 << (4 * (n) - 4))
#define UDC_IRQ_SRC_REG UDC_REG(0x30) /* Interrupt source */
# define UDC_TXN_DONE (1 << 10)
# define UDC_RXN_CNT (1 << 9)
# define UDC_RXN_EOT (1 << 8)
# define UDC_SOF (1 << 7)
# define UDC_EPN_RX (1 << 5)
# define UDC_EPN_TX (1 << 4)
# define UDC_DS_CHG (1 << 3)
# define UDC_SETUP (1 << 2)
# define UDC_EP0_RX (1 << 1)
# define UDC_EP0_TX (1 << 0)
# define UDC_IRQ_SRC_MASK 0x7bf
#define UDC_EPN_STAT_REG UDC_REG(0x34) /* EP irq status */
#define UDC_DMAN_STAT_REG UDC_REG(0x38) /* DMA irq status */
# define UDC_DMA_RX_SB (1 << 12)
# define UDC_DMA_RX_SRC(x) (((x)>>8) & 0xf)
# define UDC_DMA_TX_SRC(x) (((x)>>0) & 0xf)
/* DMA configuration registers: up to three channels in each direction. */
#define UDC_RXDMA_CFG_REG UDC_REG(0x40) /* 3 eps for RX DMA */
# define UDC_DMA_REQ (1 << 12)
#define UDC_TXDMA_CFG_REG UDC_REG(0x44) /* 3 eps for TX DMA */
#define UDC_DATA_DMA_REG UDC_REG(0x48) /* rx/tx fifo addr */
/* rx/tx dma control, numbering channels 1-3 not 0-2 */
#define UDC_TXDMA_REG(chan) UDC_REG(0x50 - 4 + 4 * (chan))
# define UDC_TXN_EOT (1 << 15) /* bytes vs packets */
# define UDC_TXN_START (1 << 14) /* start transfer */
# define UDC_TXN_TSC 0x03ff /* units in xfer */
#define UDC_RXDMA_REG(chan) UDC_REG(0x60 - 4 + 4 * (chan))
# define UDC_RXN_STOP (1 << 15) /* enable EOT irq */
# define UDC_RXN_TC 0x00ff /* packets in xfer */
/*
* Endpoint configuration registers (used before CFG_LOCK is set)
* UDC_EP_TX_REG(0) is unused
*/
#define UDC_EP_RX_REG(endpoint) UDC_REG(0x80 + (endpoint)*4)
# define UDC_EPN_RX_VALID (1 << 15)
# define UDC_EPN_RX_DB (1 << 14)
/* buffer size in bits 13, 12 */
# define UDC_EPN_RX_ISO (1 << 11)
/* buffer pointer in low 11 bits */
#define UDC_EP_TX_REG(endpoint) UDC_REG(0xc0 + (endpoint)*4)
/* same bitfields as in RX_REG */
/*-------------------------------------------------------------------------*/
struct omap_req {
struct usb_request req;
struct list_head queue;
unsigned dma_bytes;
unsigned mapped:1;
};
struct omap_ep {
struct usb_ep ep;
struct list_head queue;
unsigned long irqs;
struct list_head iso;
const struct usb_endpoint_descriptor *desc;
char name[14];
u16 maxpacket;
u8 bEndpointAddress;
u8 bmAttributes;
unsigned double_buf:1;
unsigned stopped:1;
unsigned fnf:1;
unsigned has_dma:1;
u8 ackwait;
u8 dma_channel;
u16 dma_counter;
int lch;
struct omap_udc *udc;
struct timer_list timer;
};
struct omap_udc {
struct usb_gadget gadget;
struct usb_gadget_driver *driver;
spinlock_t lock;
struct omap_ep ep[32];
u16 devstat;
u16 clr_halt;
struct otg_transceiver *transceiver;
struct list_head iso;
unsigned softconnect:1;
unsigned vbus_active:1;
unsigned ep0_pending:1;
unsigned ep0_in:1;
unsigned ep0_set_config:1;
unsigned ep0_reset_config:1;
unsigned ep0_setup:1;
struct completion *done;
};
/*-------------------------------------------------------------------------*/
#ifdef DEBUG
#define DBG(stuff...) printk(KERN_DEBUG "udc: " stuff)
#else
#define DBG(stuff...) do{}while(0)
#endif
#ifdef VERBOSE
# define VDBG DBG
#else
# define VDBG(stuff...) do{}while(0)
#endif
#define ERR(stuff...) printk(KERN_ERR "udc: " stuff)
#define WARN(stuff...) printk(KERN_WARNING "udc: " stuff)
#define INFO(stuff...) printk(KERN_INFO "udc: " stuff)
/*-------------------------------------------------------------------------*/
#define MOD_CONF_CTRL_0_REG __REG32(MOD_CONF_CTRL_0)
#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */
#define FUNC_MUX_CTRL_0_REG __REG32(FUNC_MUX_CTRL_0)
#define VBUS_CTRL_1510 (1 << 19) /* 1 connected (software) */
#define VBUS_MODE_1510 (1 << 18) /* 0 hardware, 1 software */
#define HMC_1510 ((MOD_CONF_CTRL_0_REG >> 1) & 0x3f)
#define HMC_1610 (OTG_SYSCON_2_REG & 0x3f)
#define HMC (cpu_is_omap15xx() ? HMC_1510 : HMC_1610)
View Git Blame Copy Permalink