Ido Yariv 6836989c35 ARM: davinci: DA850: Add GPIO pinmux configuration for wl1271 ... The wl1271 daughter board makes use of a few GPIOs: GPIO6_9 is used for powering down/up the WLAN functionality. GPIO6_10 is used as an input IRQ line from the WLAN chip. Add the required pinmux configuration for these GPIOs. Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>		2011-09-17 15:53:22 +05:30
..
aemif.h	davinci: add support for aemif timing configuration	2010-09-24 07:40:26 -07:00
asp.h	ASoC: davinci: let platform data define edma queue numbers	2010-07-20 09:57:20 +01:00
cdce949.h	davinci: add support for CDCE949 clock synthesizer	2010-02-04 13:29:58 -08:00
clock.h	davinci: major rework of clock, PLL, PSC infrastructure	2009-04-23 09:31:00 -07:00
common.h	Davinci: iotable based ioremap() interception	2010-05-13 10:05:31 -07:00
cp_intc.h	Davinci: aintc/cpintc - use ioremap()	2010-05-13 10:05:28 -07:00
cpufreq.h	davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator	2009-11-25 10:21:37 -08:00
cpuidle.h	davinci: cpuidle: move mapping of DDR2 controller registers out of driver	2010-02-04 13:29:38 -08:00
cputype.h	Fix common misspellings	2011-03-31 11:26:23 -03:00
da8xx.h	davinci: da850: add support for SATA interface	2011-07-08 11:13:08 +05:30
debug-macro.S	davinci: fix DEBUG_LL code for p2v changes	2011-04-19 16:54:15 -07:00
dm355.h	DaVinci: move AEMIF #define's to the proper headers	2010-05-06 15:02:06 -07:00
dm365.h	davinci: cleanup mdio arch code and switch to phy_id	2010-09-24 07:40:30 -07:00
dm644x.h	davinci: cleanup mdio arch code and switch to phy_id	2010-09-24 07:40:30 -07:00
dm646x.h	davinci: dm6467/T EVM: fix setting up of reference clock rate	2011-07-06 16:48:45 +05:30
edma.h	davinci: remove unused DA830_edma_ch enum	2011-03-11 10:48:28 -08:00
entry-macro.S	ARM: entry: remove unused irq_prio_table macro	2011-06-28 10:34:58 +01:00
gpio.h	Davinci: tnetv107x initial gpio support	2010-06-21 12:48:31 -07:00
hardware.h	davinci: move DM64XX_VDD3P3V_PWDN to devices.c	2011-05-23 22:18:26 +05:30
i2c.h	Merge branch 'for-next' into for-linus	2010-03-08 16:55:37 +01:00
io.h	ARM: io: make iounmap() a simple macro	2010-12-08 13:57:04 +00:00
irqs.h	Davinci: tnetv107x IRQ definitions	2010-05-06 15:02:05 -07:00
keyscan.h	Input: davinci_keyscan - add device_enable method to platform data	2010-01-06 00:17:11 -08:00
memory.h	ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size	2011-07-18 15:29:58 -04:00
mmc.h	davinci: mmc: pass number of SG segments as platform data	2010-05-27 09:12:39 -07:00
mux.h	ARM: davinci: DA850: Add GPIO pinmux configuration for wl1271	2011-09-17 15:53:22 +05:30
nand.h	nand: davinci: add support for timing configuration	2010-09-24 07:40:26 -07:00
pm.h	davinci: add power management support	2010-02-04 13:29:55 -08:00
psc.h	ARM: davinci: correct MDSTAT_STATE_MASK	2011-09-07 14:23:02 +05:30
serial.h	davinci: fix DEBUG_LL code for p2v changes	2011-04-19 16:54:15 -07:00
spi.h	davinci: spi: move event queue parameter to platform data	2011-02-28 14:53:29 -08:00
sram.h	davinci: add SRAM allocator	2009-05-28 15:18:13 -07:00
system.h	Davinci: watchdog reset separation across socs	2010-05-06 15:02:09 -07:00
time.h	davinci: Add watchdog base address flexibility	2009-05-26 08:20:31 -07:00
timex.h	davinci: explain CLOCK_TICK_RATE of 27MHz in include/mach/timex.h	2010-02-04 13:29:41 -08:00
tnetv107x.h	davinci: add tnetv107x ssp platform device	2011-03-15 08:17:22 -07:00
uncompress.h	ARM: zImage: remove the static qualifier from global data variables	2011-05-07 00:08:02 -04:00
usb.h	DaVinci: rename setup_usb() to davinci_setup_usb()	2009-11-25 10:21:33 -08:00
vmalloc.h	davinci: Move IO device mapping macros from io.h to hardware.h	2009-08-26 10:57:01 +03:00