mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-22 20:23:57 +08:00
4ffea5e083
The max8998 has a current regulator for charging control. The charger driver in drivers/power/supply/max8998_charger.c has a comment in it stating that 'charger control is done by a current regulator "CHARGER"', but this regulator was never added until now. The current values have been extracted from a downstream driver for the SGH-T959V. Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Link: https://lore.kernel.org/r/BN6PR04MB0660E1F4A3D5A348BE88311CA3BA0@BN6PR04MB0660.namprd04.prod.outlook.com Signed-off-by: Mark Brown <broonie@kernel.org>
107 lines
2.9 KiB
C
107 lines
2.9 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* max8998.h - Voltage regulator driver for the Maxim 8998
|
|
*
|
|
* Copyright (C) 2009-2010 Samsung Electrnoics
|
|
* Kyungmin Park <kyungmin.park@samsung.com>
|
|
* Marek Szyprowski <m.szyprowski@samsung.com>
|
|
*/
|
|
|
|
#ifndef __LINUX_MFD_MAX8998_H
|
|
#define __LINUX_MFD_MAX8998_H
|
|
|
|
#include <linux/regulator/machine.h>
|
|
|
|
/* MAX 8998 regulator ids */
|
|
enum {
|
|
MAX8998_LDO2 = 2,
|
|
MAX8998_LDO3,
|
|
MAX8998_LDO4,
|
|
MAX8998_LDO5,
|
|
MAX8998_LDO6,
|
|
MAX8998_LDO7,
|
|
MAX8998_LDO8,
|
|
MAX8998_LDO9,
|
|
MAX8998_LDO10,
|
|
MAX8998_LDO11,
|
|
MAX8998_LDO12,
|
|
MAX8998_LDO13,
|
|
MAX8998_LDO14,
|
|
MAX8998_LDO15,
|
|
MAX8998_LDO16,
|
|
MAX8998_LDO17,
|
|
MAX8998_BUCK1,
|
|
MAX8998_BUCK2,
|
|
MAX8998_BUCK3,
|
|
MAX8998_BUCK4,
|
|
MAX8998_EN32KHZ_AP,
|
|
MAX8998_EN32KHZ_CP,
|
|
MAX8998_ENVICHG,
|
|
MAX8998_ESAFEOUT1,
|
|
MAX8998_ESAFEOUT2,
|
|
MAX8998_CHARGER,
|
|
};
|
|
|
|
/**
|
|
* max8998_regulator_data - regulator data
|
|
* @id: regulator id
|
|
* @initdata: regulator init data (contraints, supplies, ...)
|
|
* @reg_node: DT node of regulator (unused on non-DT platforms)
|
|
*/
|
|
struct max8998_regulator_data {
|
|
int id;
|
|
struct regulator_init_data *initdata;
|
|
struct device_node *reg_node;
|
|
};
|
|
|
|
/**
|
|
* struct max8998_board - packages regulator init data
|
|
* @regulators: array of defined regulators
|
|
* @num_regulators: number of regulators used
|
|
* @irq_base: base IRQ number for max8998, required for IRQs
|
|
* @ono: power onoff IRQ number for max8998
|
|
* @buck_voltage_lock: Do NOT change the values of the following six
|
|
* registers set by buck?_voltage?. The voltage of BUCK1/2 cannot
|
|
* be other than the preset values.
|
|
* @buck1_voltage: BUCK1 DVS mode 1 voltage registers
|
|
* @buck2_voltage: BUCK2 DVS mode 2 voltage registers
|
|
* @buck1_set1: BUCK1 gpio pin 1 to set output voltage
|
|
* @buck1_set2: BUCK1 gpio pin 2 to set output voltage
|
|
* @buck1_default_idx: Default for BUCK1 gpio pin 1, 2
|
|
* @buck2_set3: BUCK2 gpio pin to set output voltage
|
|
* @buck2_default_idx: Default for BUCK2 gpio pin.
|
|
* @wakeup: Allow to wake up from suspend
|
|
* @rtc_delay: LP3974 RTC chip bug that requires delay after a register
|
|
* write before reading it.
|
|
* @eoc: End of Charge Level in percent: 10% ~ 45% by 5% step
|
|
* If it equals 0, leave it unchanged.
|
|
* Otherwise, it is a invalid value.
|
|
* @restart: Restart Level in mV: 100, 150, 200, and -1 for disable.
|
|
* If it equals 0, leave it unchanged.
|
|
* Otherwise, it is a invalid value.
|
|
* @timeout: Full Timeout in hours: 5, 6, 7, and -1 for disable.
|
|
* If it equals 0, leave it unchanged.
|
|
* Otherwise, leave it unchanged.
|
|
*/
|
|
struct max8998_platform_data {
|
|
struct max8998_regulator_data *regulators;
|
|
int num_regulators;
|
|
unsigned int irq_base;
|
|
int ono;
|
|
bool buck_voltage_lock;
|
|
int buck1_voltage[4];
|
|
int buck2_voltage[2];
|
|
int buck1_set1;
|
|
int buck1_set2;
|
|
int buck1_default_idx;
|
|
int buck2_set3;
|
|
int buck2_default_idx;
|
|
bool wakeup;
|
|
bool rtc_delay;
|
|
int eoc;
|
|
int restart;
|
|
int timeout;
|
|
};
|
|
|
|
#endif /* __LINUX_MFD_MAX8998_H */
|