mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 14:43:58 +08:00
53e1941ce8
The property marvell,wakeup-pin and marvell,wakeup-gap-ms are read as u16 in the driver. Fix documentation and example accordingly. Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org> Signed-off-by: Rob Herring <robh@kernel.org>
57 lines
1.9 KiB
Plaintext
57 lines
1.9 KiB
Plaintext
Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices
|
|
------
|
|
|
|
Required properties:
|
|
|
|
- compatible : should be one of the following:
|
|
* "marvell,sd8897-bt"
|
|
* "marvell,sd8997-bt"
|
|
|
|
Optional properties:
|
|
|
|
- marvell,cal-data: Calibration data downloaded to the device during
|
|
initialization. This is an array of 28 values(u8).
|
|
|
|
- marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
|
|
firmware will use the pin to wakeup host system (u16).
|
|
- marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
|
|
platform. The value will be configured to firmware. This
|
|
is needed to work chip's sleep feature as expected (u16).
|
|
- interrupt-parent: phandle of the parent interrupt controller
|
|
- interrupts : interrupt pin number to the cpu. Driver will request an irq based
|
|
on this interrupt number. During system suspend, the irq will be
|
|
enabled so that the bluetooth chip can wakeup host platform under
|
|
certain condition. During system resume, the irq will be disabled
|
|
to make sure unnecessary interrupt is not received.
|
|
|
|
Example:
|
|
|
|
IRQ pin 119 is used as system wakeup source interrupt.
|
|
wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host
|
|
using this device side pin and wakeup latency.
|
|
calibration data is also available in below example.
|
|
|
|
&mmc3 {
|
|
status = "okay";
|
|
vmmc-supply = <&wlan_en_reg>;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
keep-power-in-suspend;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
btmrvl: bluetooth@2 {
|
|
compatible = "marvell,sd8897-bt";
|
|
reg = <2>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
marvell,cal-data = /bits/ 8 <
|
|
0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
|
|
0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
|
|
0x00 0x00 0xf0 0x00>;
|
|
marvell,wakeup-pin = /bits/ 16 <0x0d>;
|
|
marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
|
|
};
|
|
};
|