2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-24 05:04:00 +08:00
linux-next/Documentation/misc-devices/c2port.txt
Justin P. Mattock 0ea6e61122 Documentation: update broken web addresses.
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-04 15:21:40 +02:00

91 lines
2.8 KiB
Plaintext

C2 port support
---------------
(C) Copyright 2007 Rodolfo Giometti <giometti@enneenne.com>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
Overview
--------
This driver implements the support for Linux of Silicon Labs (Silabs)
C2 Interface used for in-system programming of micro controllers.
By using this driver you can reprogram the in-system flash without EC2
or EC3 debug adapter. This solution is also useful in those systems
where the micro controller is connected via special GPIOs pins.
References
----------
The C2 Interface main references are at (http://www.silabs.com)
Silicon Laboratories site], see:
- AN127: FLASH Programming via the C2 Interface at
http://www.silabs.com/Support Documents/TechnicalDocs/an127.pdf
- C2 Specification at
http://www.silabs.com/pages/DownloadDoc.aspx?FILEURL=Support%20Documents/TechnicalDocs/an127.pdf&src=SearchResults
however it implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices. Currently
this code supports only flash programming but extensions are easy to
add.
Using the driver
----------------
Once the driver is loaded you can use sysfs support to get C2port's
info or read/write in-system flash.
# ls /sys/class/c2port/c2port0/
access flash_block_size flash_erase rev_id
dev_id flash_blocks_num flash_size subsystem/
flash_access flash_data reset uevent
Initially the C2port access is disabled since you hardware may have
such lines multiplexed with other devices so, to get access to the
C2port, you need the command:
# echo 1 > /sys/class/c2port/c2port0/access
after that you should read the device ID and revision ID of the
connected micro controller:
# cat /sys/class/c2port/c2port0/dev_id
8
# cat /sys/class/c2port/c2port0/rev_id
1
However, for security reasons, the in-system flash access in not
enabled yet, to do so you need the command:
# echo 1 > /sys/class/c2port/c2port0/flash_access
After that you can read the whole flash:
# cat /sys/class/c2port/c2port0/flash_data > image
erase it:
# echo 1 > /sys/class/c2port/c2port0/flash_erase
and write it:
# cat image > /sys/class/c2port/c2port0/flash_data
after writing you have to reset the device to execute the new code:
# echo 1 > /sys/class/c2port/c2port0/reset