2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-30 08:04:13 +08:00
linux-next/drivers/gpio/gpio-generic.c
Shawn Guo 3e11f7b840 gpio/generic: initialize basic_mmio_gpio shadow variables properly
It fixes the issue in gpio-generic that commit fb14921 (gpio/mxc: add
missing initialization of basic_mmio_gpio shadow variables) manged to
fix in gpio-mxc driver, so that other platform specific drivers do not
suffer from the same problem over and over again.

Changes since v1:
* Turn the last parameter of bgpio_init() "bool big_endian" into
  "unsigned long flags" and give those really quirky hardwares a
  chance to tell that reg_set and reg_dir are unreadable.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: Fix big-endian usage to explicitly set BBGPIOF_BIG_ENDIAN]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-05-19 12:17:35 -06:00

540 lines
13 KiB
C

/*
* Generic driver for memory-mapped GPIO controllers.
*
* Copyright 2008 MontaVista Software, Inc.
* Copyright 2008,2010 Anton Vorontsov <cbouatmailru@gmail.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* ....``.```~~~~````.`.`.`.`.```````'',,,.........`````......`.......
* ...`` ```````..
* ..The simplest form of a GPIO controller that the driver supports is``
* `.just a single "data" register, where GPIO state can be read and/or `
* `,..written. ,,..``~~~~ .....``.`.`.~~.```.`.........``````.```````
* `````````
___
_/~~|___/~| . ```~~~~~~ ___/___\___ ,~.`.`.`.`````.~~...,,,,...
__________|~$@~~~ %~ /o*o*o*o*o*o\ .. Implementing such a GPIO .
o ` ~~~~\___/~~~~ ` controller in FPGA is ,.`
`....trivial..'~`.```.```
* ```````
* .```````~~~~`..`.``.``.
* . The driver supports `... ,..```.`~~~```````````````....````.``,,
* . big-endian notation, just`. .. A bit more sophisticated controllers ,
* . register the device with -be`. .with a pair of set/clear-bit registers ,
* `.. suffix. ```~~`````....`.` . affecting the data register and the .`
* ``.`.``...``` ```.. output pins are also supported.`
* ^^ `````.`````````.,``~``~``~~``````
* . ^^
* ,..`.`.`...````````````......`.`.`.`.`.`..`.`.`..
* .. The expectation is that in at least some cases . ,-~~~-,
* .this will be used with roll-your-own ASIC/FPGA .` \ /
* .logic in Verilog or VHDL. ~~~`````````..`````~~` \ /
* ..````````......``````````` \o_
* |
* ^^ / \
*
* ...`````~~`.....``.`..........``````.`.``.```........``.
* ` 8, 16, 32 and 64 bits registers are supported, and``.
* . the number of GPIOs is determined by the width of ~
* .. the registers. ,............```.`.`..`.`.~~~.`.`.`~
* `.......````.```
*/
#include <linux/init.h>
#include <linux/err.h>
#include <linux/bug.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/compiler.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/log2.h>
#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/mod_devicetable.h>
#include <linux/basic_mmio_gpio.h>
static void bgpio_write8(void __iomem *reg, unsigned long data)
{
writeb(data, reg);
}
static unsigned long bgpio_read8(void __iomem *reg)
{
return readb(reg);
}
static void bgpio_write16(void __iomem *reg, unsigned long data)
{
writew(data, reg);
}
static unsigned long bgpio_read16(void __iomem *reg)
{
return readw(reg);
}
static void bgpio_write32(void __iomem *reg, unsigned long data)
{
writel(data, reg);
}
static unsigned long bgpio_read32(void __iomem *reg)
{
return readl(reg);
}
#if BITS_PER_LONG >= 64
static void bgpio_write64(void __iomem *reg, unsigned long data)
{
writeq(data, reg);
}
static unsigned long bgpio_read64(void __iomem *reg)
{
return readq(reg);
}
#endif /* BITS_PER_LONG >= 64 */
static unsigned long bgpio_pin2mask(struct bgpio_chip *bgc, unsigned int pin)
{
return 1 << pin;
}
static unsigned long bgpio_pin2mask_be(struct bgpio_chip *bgc,
unsigned int pin)
{
return 1 << (bgc->bits - 1 - pin);
}
static int bgpio_get(struct gpio_chip *gc, unsigned int gpio)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
return bgc->read_reg(bgc->reg_dat) & bgc->pin2mask(bgc, gpio);
}
static void bgpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long mask = bgc->pin2mask(bgc, gpio);
unsigned long flags;
spin_lock_irqsave(&bgc->lock, flags);
if (val)
bgc->data |= mask;
else
bgc->data &= ~mask;
bgc->write_reg(bgc->reg_dat, bgc->data);
spin_unlock_irqrestore(&bgc->lock, flags);
}
static void bgpio_set_with_clear(struct gpio_chip *gc, unsigned int gpio,
int val)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long mask = bgc->pin2mask(bgc, gpio);
if (val)
bgc->write_reg(bgc->reg_set, mask);
else
bgc->write_reg(bgc->reg_clr, mask);
}
static void bgpio_set_set(struct gpio_chip *gc, unsigned int gpio, int val)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long mask = bgc->pin2mask(bgc, gpio);
unsigned long flags;
spin_lock_irqsave(&bgc->lock, flags);
if (val)
bgc->data |= mask;
else
bgc->data &= ~mask;
bgc->write_reg(bgc->reg_set, bgc->data);
spin_unlock_irqrestore(&bgc->lock, flags);
}
static int bgpio_simple_dir_in(struct gpio_chip *gc, unsigned int gpio)
{
return 0;
}
static int bgpio_simple_dir_out(struct gpio_chip *gc, unsigned int gpio,
int val)
{
gc->set(gc, gpio, val);
return 0;
}
static int bgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long flags;
spin_lock_irqsave(&bgc->lock, flags);
bgc->dir &= ~bgc->pin2mask(bgc, gpio);
bgc->write_reg(bgc->reg_dir, bgc->dir);
spin_unlock_irqrestore(&bgc->lock, flags);
return 0;
}
static int bgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long flags;
gc->set(gc, gpio, val);
spin_lock_irqsave(&bgc->lock, flags);
bgc->dir |= bgc->pin2mask(bgc, gpio);
bgc->write_reg(bgc->reg_dir, bgc->dir);
spin_unlock_irqrestore(&bgc->lock, flags);
return 0;
}
static int bgpio_dir_in_inv(struct gpio_chip *gc, unsigned int gpio)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long flags;
spin_lock_irqsave(&bgc->lock, flags);
bgc->dir |= bgc->pin2mask(bgc, gpio);
bgc->write_reg(bgc->reg_dir, bgc->dir);
spin_unlock_irqrestore(&bgc->lock, flags);
return 0;
}
static int bgpio_dir_out_inv(struct gpio_chip *gc, unsigned int gpio, int val)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
unsigned long flags;
gc->set(gc, gpio, val);
spin_lock_irqsave(&bgc->lock, flags);
bgc->dir &= ~bgc->pin2mask(bgc, gpio);
bgc->write_reg(bgc->reg_dir, bgc->dir);
spin_unlock_irqrestore(&bgc->lock, flags);
return 0;
}
static int bgpio_setup_accessors(struct device *dev,
struct bgpio_chip *bgc,
bool be)
{
switch (bgc->bits) {
case 8:
bgc->read_reg = bgpio_read8;
bgc->write_reg = bgpio_write8;
break;
case 16:
bgc->read_reg = bgpio_read16;
bgc->write_reg = bgpio_write16;
break;
case 32:
bgc->read_reg = bgpio_read32;
bgc->write_reg = bgpio_write32;
break;
#if BITS_PER_LONG >= 64
case 64:
bgc->read_reg = bgpio_read64;
bgc->write_reg = bgpio_write64;
break;
#endif /* BITS_PER_LONG >= 64 */
default:
dev_err(dev, "unsupported data width %u bits\n", bgc->bits);
return -EINVAL;
}
bgc->pin2mask = be ? bgpio_pin2mask_be : bgpio_pin2mask;
return 0;
}
/*
* Create the device and allocate the resources. For setting GPIO's there are
* three supported configurations:
*
* - single input/output register resource (named "dat").
* - set/clear pair (named "set" and "clr").
* - single output register resource and single input resource ("set" and
* dat").
*
* For the single output register, this drives a 1 by setting a bit and a zero
* by clearing a bit. For the set clr pair, this drives a 1 by setting a bit
* in the set register and clears it by setting a bit in the clear register.
* The configuration is detected by which resources are present.
*
* For setting the GPIO direction, there are three supported configurations:
*
* - simple bidirection GPIO that requires no configuration.
* - an output direction register (named "dirout") where a 1 bit
* indicates the GPIO is an output.
* - an input direction register (named "dirin") where a 1 bit indicates
* the GPIO is an input.
*/
static int bgpio_setup_io(struct bgpio_chip *bgc,
void __iomem *dat,
void __iomem *set,
void __iomem *clr)
{
bgc->reg_dat = dat;
if (!bgc->reg_dat)
return -EINVAL;
if (set && clr) {
bgc->reg_set = set;
bgc->reg_clr = clr;
bgc->gc.set = bgpio_set_with_clear;
} else if (set && !clr) {
bgc->reg_set = set;
bgc->gc.set = bgpio_set_set;
} else {
bgc->gc.set = bgpio_set;
}
bgc->gc.get = bgpio_get;
return 0;
}
static int bgpio_setup_direction(struct bgpio_chip *bgc,
void __iomem *dirout,
void __iomem *dirin)
{
if (dirout && dirin) {
return -EINVAL;
} else if (dirout) {
bgc->reg_dir = dirout;
bgc->gc.direction_output = bgpio_dir_out;
bgc->gc.direction_input = bgpio_dir_in;
} else if (dirin) {
bgc->reg_dir = dirin;
bgc->gc.direction_output = bgpio_dir_out_inv;
bgc->gc.direction_input = bgpio_dir_in_inv;
} else {
bgc->gc.direction_output = bgpio_simple_dir_out;
bgc->gc.direction_input = bgpio_simple_dir_in;
}
return 0;
}
int bgpio_remove(struct bgpio_chip *bgc)
{
int err = gpiochip_remove(&bgc->gc);
kfree(bgc);
return err;
}
EXPORT_SYMBOL_GPL(bgpio_remove);
int bgpio_init(struct bgpio_chip *bgc, struct device *dev,
unsigned long sz, void __iomem *dat, void __iomem *set,
void __iomem *clr, void __iomem *dirout, void __iomem *dirin,
unsigned long flags)
{
int ret;
if (!is_power_of_2(sz))
return -EINVAL;
bgc->bits = sz * 8;
if (bgc->bits > BITS_PER_LONG)
return -EINVAL;
spin_lock_init(&bgc->lock);
bgc->gc.dev = dev;
bgc->gc.label = dev_name(dev);
bgc->gc.base = -1;
bgc->gc.ngpio = bgc->bits;
ret = bgpio_setup_io(bgc, dat, set, clr);
if (ret)
return ret;
ret = bgpio_setup_accessors(dev, bgc, flags & BGPIOF_BIG_ENDIAN);
if (ret)
return ret;
ret = bgpio_setup_direction(bgc, dirout, dirin);
if (ret)
return ret;
bgc->data = bgc->read_reg(bgc->reg_dat);
if (bgc->gc.set == bgpio_set_set &&
!(flags & BGPIOF_UNREADABLE_REG_SET))
bgc->data = bgc->read_reg(bgc->reg_set);
if (bgc->reg_dir && !(flags & BGPIOF_UNREADABLE_REG_DIR))
bgc->dir = bgc->read_reg(bgc->reg_dir);
return ret;
}
EXPORT_SYMBOL_GPL(bgpio_init);
#ifdef CONFIG_GPIO_GENERIC_PLATFORM
static void __iomem *bgpio_map(struct platform_device *pdev,
const char *name,
resource_size_t sane_sz,
int *err)
{
struct device *dev = &pdev->dev;
struct resource *r;
resource_size_t start;
resource_size_t sz;
void __iomem *ret;
*err = 0;
r = platform_get_resource_byname(pdev, IORESOURCE_MEM, name);
if (!r)
return NULL;
sz = resource_size(r);
if (sz != sane_sz) {
*err = -EINVAL;
return NULL;
}
start = r->start;
if (!devm_request_mem_region(dev, start, sz, r->name)) {
*err = -EBUSY;
return NULL;
}
ret = devm_ioremap(dev, start, sz);
if (!ret) {
*err = -ENOMEM;
return NULL;
}
return ret;
}
static int __devinit bgpio_pdev_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct resource *r;
void __iomem *dat;
void __iomem *set;
void __iomem *clr;
void __iomem *dirout;
void __iomem *dirin;
unsigned long sz;
unsigned long flags = 0;
int err;
struct bgpio_chip *bgc;
struct bgpio_pdata *pdata = dev_get_platdata(dev);
r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dat");
if (!r)
return -EINVAL;
sz = resource_size(r);
dat = bgpio_map(pdev, "dat", sz, &err);
if (!dat)
return err ? err : -EINVAL;
set = bgpio_map(pdev, "set", sz, &err);
if (err)
return err;
clr = bgpio_map(pdev, "clr", sz, &err);
if (err)
return err;
dirout = bgpio_map(pdev, "dirout", sz, &err);
if (err)
return err;
dirin = bgpio_map(pdev, "dirin", sz, &err);
if (err)
return err;
if (!strcmp(platform_get_device_id(pdev)->name, "basic-mmio-gpio-be"))
flags |= BGPIOF_BIG_ENDIAN;
bgc = devm_kzalloc(&pdev->dev, sizeof(*bgc), GFP_KERNEL);
if (!bgc)
return -ENOMEM;
err = bgpio_init(bgc, dev, sz, dat, set, clr, dirout, dirin, flags);
if (err)
return err;
if (pdata) {
bgc->gc.base = pdata->base;
if (pdata->ngpio > 0)
bgc->gc.ngpio = pdata->ngpio;
}
platform_set_drvdata(pdev, bgc);
return gpiochip_add(&bgc->gc);
}
static int __devexit bgpio_pdev_remove(struct platform_device *pdev)
{
struct bgpio_chip *bgc = platform_get_drvdata(pdev);
return bgpio_remove(bgc);
}
static const struct platform_device_id bgpio_id_table[] = {
{ "basic-mmio-gpio", },
{ "basic-mmio-gpio-be", },
{},
};
MODULE_DEVICE_TABLE(platform, bgpio_id_table);
static struct platform_driver bgpio_driver = {
.driver = {
.name = "basic-mmio-gpio",
},
.id_table = bgpio_id_table,
.probe = bgpio_pdev_probe,
.remove = __devexit_p(bgpio_pdev_remove),
};
module_platform_driver(bgpio_driver);
#endif /* CONFIG_GPIO_GENERIC_PLATFORM */
MODULE_DESCRIPTION("Driver for basic memory-mapped GPIO controllers");
MODULE_AUTHOR("Anton Vorontsov <cbouatmailru@gmail.com>");
MODULE_LICENSE("GPL");