mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 04:34:11 +08:00
53a09635ce
This adds SPI support for the Sparx5 SoC, which is using the MMIO Designware SPI controller. The Sparx5 differs from the Ocelot version in these areas: * The CS override is controlled by a new set of registers for this purpose. * The Sparx5 SPI controller has the RX sample delay register, and it must be configured for the (SPI NAND) device on SPI2. * The Sparx5 SPI controller has 2 different SPI bus interfaces on the same controller (don't ask...). The "spi-mux" driver should be used in conjunction with the SPI driver to select the appropriate bus. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com> Link: https://lore.kernel.org/r/20200824203010.2033-3-lars.povlsen@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
394 lines
10 KiB
C
394 lines
10 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Memory-mapped interface driver for DW SPI Core
|
|
*
|
|
* Copyright (c) 2010, Octasic semiconductor.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/err.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/scatterlist.h>
|
|
#include <linux/mfd/syscon.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_platform.h>
|
|
#include <linux/acpi.h>
|
|
#include <linux/property.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/reset.h>
|
|
|
|
#include "spi-dw.h"
|
|
|
|
#define DRIVER_NAME "dw_spi_mmio"
|
|
|
|
struct dw_spi_mmio {
|
|
struct dw_spi dws;
|
|
struct clk *clk;
|
|
struct clk *pclk;
|
|
void *priv;
|
|
struct reset_control *rstc;
|
|
};
|
|
|
|
#define MSCC_CPU_SYSTEM_CTRL_GENERAL_CTRL 0x24
|
|
#define OCELOT_IF_SI_OWNER_OFFSET 4
|
|
#define JAGUAR2_IF_SI_OWNER_OFFSET 6
|
|
#define MSCC_IF_SI_OWNER_MASK GENMASK(1, 0)
|
|
#define MSCC_IF_SI_OWNER_SISL 0
|
|
#define MSCC_IF_SI_OWNER_SIBM 1
|
|
#define MSCC_IF_SI_OWNER_SIMC 2
|
|
|
|
#define MSCC_SPI_MST_SW_MODE 0x14
|
|
#define MSCC_SPI_MST_SW_MODE_SW_PIN_CTRL_MODE BIT(13)
|
|
#define MSCC_SPI_MST_SW_MODE_SW_SPI_CS(x) (x << 5)
|
|
|
|
#define SPARX5_FORCE_ENA 0xa4
|
|
#define SPARX5_FORCE_VAL 0xa8
|
|
|
|
/*
|
|
* For Keem Bay, CTRLR0[31] is used to select controller mode.
|
|
* 0: SSI is slave
|
|
* 1: SSI is master
|
|
*/
|
|
#define KEEMBAY_CTRLR0_SSIC_IS_MST BIT(31)
|
|
|
|
struct dw_spi_mscc {
|
|
struct regmap *syscon;
|
|
void __iomem *spi_mst; /* Not sparx5 */
|
|
};
|
|
|
|
/*
|
|
* The Designware SPI controller (referred to as master in the documentation)
|
|
* automatically deasserts chip select when the tx fifo is empty. The chip
|
|
* selects then needs to be either driven as GPIOs or, for the first 4 using the
|
|
* the SPI boot controller registers. the final chip select is an OR gate
|
|
* between the Designware SPI controller and the SPI boot controller.
|
|
*/
|
|
static void dw_spi_mscc_set_cs(struct spi_device *spi, bool enable)
|
|
{
|
|
struct dw_spi *dws = spi_master_get_devdata(spi->master);
|
|
struct dw_spi_mmio *dwsmmio = container_of(dws, struct dw_spi_mmio, dws);
|
|
struct dw_spi_mscc *dwsmscc = dwsmmio->priv;
|
|
u32 cs = spi->chip_select;
|
|
|
|
if (cs < 4) {
|
|
u32 sw_mode = MSCC_SPI_MST_SW_MODE_SW_PIN_CTRL_MODE;
|
|
|
|
if (!enable)
|
|
sw_mode |= MSCC_SPI_MST_SW_MODE_SW_SPI_CS(BIT(cs));
|
|
|
|
writel(sw_mode, dwsmscc->spi_mst + MSCC_SPI_MST_SW_MODE);
|
|
}
|
|
|
|
dw_spi_set_cs(spi, enable);
|
|
}
|
|
|
|
static int dw_spi_mscc_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio,
|
|
const char *cpu_syscon, u32 if_si_owner_offset)
|
|
{
|
|
struct dw_spi_mscc *dwsmscc;
|
|
|
|
dwsmscc = devm_kzalloc(&pdev->dev, sizeof(*dwsmscc), GFP_KERNEL);
|
|
if (!dwsmscc)
|
|
return -ENOMEM;
|
|
|
|
dwsmscc->spi_mst = devm_platform_ioremap_resource(pdev, 1);
|
|
if (IS_ERR(dwsmscc->spi_mst)) {
|
|
dev_err(&pdev->dev, "SPI_MST region map failed\n");
|
|
return PTR_ERR(dwsmscc->spi_mst);
|
|
}
|
|
|
|
dwsmscc->syscon = syscon_regmap_lookup_by_compatible(cpu_syscon);
|
|
if (IS_ERR(dwsmscc->syscon))
|
|
return PTR_ERR(dwsmscc->syscon);
|
|
|
|
/* Deassert all CS */
|
|
writel(0, dwsmscc->spi_mst + MSCC_SPI_MST_SW_MODE);
|
|
|
|
/* Select the owner of the SI interface */
|
|
regmap_update_bits(dwsmscc->syscon, MSCC_CPU_SYSTEM_CTRL_GENERAL_CTRL,
|
|
MSCC_IF_SI_OWNER_MASK << if_si_owner_offset,
|
|
MSCC_IF_SI_OWNER_SIMC << if_si_owner_offset);
|
|
|
|
dwsmmio->dws.set_cs = dw_spi_mscc_set_cs;
|
|
dwsmmio->priv = dwsmscc;
|
|
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_spi_mscc_ocelot_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
return dw_spi_mscc_init(pdev, dwsmmio, "mscc,ocelot-cpu-syscon",
|
|
OCELOT_IF_SI_OWNER_OFFSET);
|
|
}
|
|
|
|
static int dw_spi_mscc_jaguar2_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
return dw_spi_mscc_init(pdev, dwsmmio, "mscc,jaguar2-cpu-syscon",
|
|
JAGUAR2_IF_SI_OWNER_OFFSET);
|
|
}
|
|
|
|
/*
|
|
* The Designware SPI controller (referred to as master in the
|
|
* documentation) automatically deasserts chip select when the tx fifo
|
|
* is empty. The chip selects then needs to be driven by a CS override
|
|
* register. enable is an active low signal.
|
|
*/
|
|
static void dw_spi_sparx5_set_cs(struct spi_device *spi, bool enable)
|
|
{
|
|
struct dw_spi *dws = spi_master_get_devdata(spi->master);
|
|
struct dw_spi_mmio *dwsmmio = container_of(dws, struct dw_spi_mmio, dws);
|
|
struct dw_spi_mscc *dwsmscc = dwsmmio->priv;
|
|
u8 cs = spi->chip_select;
|
|
|
|
if (!enable) {
|
|
/* CS override drive enable */
|
|
regmap_write(dwsmscc->syscon, SPARX5_FORCE_ENA, 1);
|
|
/* Now set CSx enabled */
|
|
regmap_write(dwsmscc->syscon, SPARX5_FORCE_VAL, ~BIT(cs));
|
|
/* Allow settle */
|
|
usleep_range(1, 5);
|
|
} else {
|
|
/* CS value */
|
|
regmap_write(dwsmscc->syscon, SPARX5_FORCE_VAL, ~0);
|
|
/* Allow settle */
|
|
usleep_range(1, 5);
|
|
/* CS override drive disable */
|
|
regmap_write(dwsmscc->syscon, SPARX5_FORCE_ENA, 0);
|
|
}
|
|
|
|
dw_spi_set_cs(spi, enable);
|
|
}
|
|
|
|
static int dw_spi_mscc_sparx5_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
const char *syscon_name = "microchip,sparx5-cpu-syscon";
|
|
struct device *dev = &pdev->dev;
|
|
struct dw_spi_mscc *dwsmscc;
|
|
|
|
if (!IS_ENABLED(CONFIG_SPI_MUX)) {
|
|
dev_err(dev, "This driver needs CONFIG_SPI_MUX\n");
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
dwsmscc = devm_kzalloc(dev, sizeof(*dwsmscc), GFP_KERNEL);
|
|
if (!dwsmscc)
|
|
return -ENOMEM;
|
|
|
|
dwsmscc->syscon =
|
|
syscon_regmap_lookup_by_compatible(syscon_name);
|
|
if (IS_ERR(dwsmscc->syscon)) {
|
|
dev_err(dev, "No syscon map %s\n", syscon_name);
|
|
return PTR_ERR(dwsmscc->syscon);
|
|
}
|
|
|
|
dwsmmio->dws.set_cs = dw_spi_sparx5_set_cs;
|
|
dwsmmio->priv = dwsmscc;
|
|
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_spi_alpine_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
dwsmmio->dws.cs_override = 1;
|
|
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_spi_dw_apb_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0;
|
|
|
|
dw_spi_dma_setup_generic(&dwsmmio->dws);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_spi_dwc_ssi_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0_v1_01a;
|
|
|
|
dw_spi_dma_setup_generic(&dwsmmio->dws);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static u32 dw_spi_update_cr0_keembay(struct spi_controller *master,
|
|
struct spi_device *spi,
|
|
struct spi_transfer *transfer)
|
|
{
|
|
u32 cr0 = dw_spi_update_cr0_v1_01a(master, spi, transfer);
|
|
|
|
return cr0 | KEEMBAY_CTRLR0_SSIC_IS_MST;
|
|
}
|
|
|
|
static int dw_spi_keembay_init(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio)
|
|
{
|
|
/* Register hook to configure CTRLR0 */
|
|
dwsmmio->dws.update_cr0 = dw_spi_update_cr0_keembay;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dw_spi_mmio_probe(struct platform_device *pdev)
|
|
{
|
|
int (*init_func)(struct platform_device *pdev,
|
|
struct dw_spi_mmio *dwsmmio);
|
|
struct dw_spi_mmio *dwsmmio;
|
|
struct resource *mem;
|
|
struct dw_spi *dws;
|
|
int ret;
|
|
int num_cs;
|
|
|
|
dwsmmio = devm_kzalloc(&pdev->dev, sizeof(struct dw_spi_mmio),
|
|
GFP_KERNEL);
|
|
if (!dwsmmio)
|
|
return -ENOMEM;
|
|
|
|
dws = &dwsmmio->dws;
|
|
|
|
/* Get basic io resource and map it */
|
|
dws->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &mem);
|
|
if (IS_ERR(dws->regs))
|
|
return PTR_ERR(dws->regs);
|
|
|
|
dws->paddr = mem->start;
|
|
|
|
dws->irq = platform_get_irq(pdev, 0);
|
|
if (dws->irq < 0)
|
|
return dws->irq; /* -ENXIO */
|
|
|
|
dwsmmio->clk = devm_clk_get(&pdev->dev, NULL);
|
|
if (IS_ERR(dwsmmio->clk))
|
|
return PTR_ERR(dwsmmio->clk);
|
|
ret = clk_prepare_enable(dwsmmio->clk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Optional clock needed to access the registers */
|
|
dwsmmio->pclk = devm_clk_get_optional(&pdev->dev, "pclk");
|
|
if (IS_ERR(dwsmmio->pclk)) {
|
|
ret = PTR_ERR(dwsmmio->pclk);
|
|
goto out_clk;
|
|
}
|
|
ret = clk_prepare_enable(dwsmmio->pclk);
|
|
if (ret)
|
|
goto out_clk;
|
|
|
|
/* find an optional reset controller */
|
|
dwsmmio->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, "spi");
|
|
if (IS_ERR(dwsmmio->rstc)) {
|
|
ret = PTR_ERR(dwsmmio->rstc);
|
|
goto out_clk;
|
|
}
|
|
reset_control_deassert(dwsmmio->rstc);
|
|
|
|
dws->bus_num = pdev->id;
|
|
|
|
dws->max_freq = clk_get_rate(dwsmmio->clk);
|
|
|
|
device_property_read_u32(&pdev->dev, "reg-io-width", &dws->reg_io_width);
|
|
|
|
num_cs = 4;
|
|
|
|
device_property_read_u32(&pdev->dev, "num-cs", &num_cs);
|
|
|
|
dws->num_cs = num_cs;
|
|
|
|
init_func = device_get_match_data(&pdev->dev);
|
|
if (init_func) {
|
|
ret = init_func(pdev, dwsmmio);
|
|
if (ret)
|
|
goto out;
|
|
}
|
|
|
|
pm_runtime_enable(&pdev->dev);
|
|
|
|
ret = dw_spi_add_host(&pdev->dev, dws);
|
|
if (ret)
|
|
goto out;
|
|
|
|
platform_set_drvdata(pdev, dwsmmio);
|
|
return 0;
|
|
|
|
out:
|
|
pm_runtime_disable(&pdev->dev);
|
|
clk_disable_unprepare(dwsmmio->pclk);
|
|
out_clk:
|
|
clk_disable_unprepare(dwsmmio->clk);
|
|
reset_control_assert(dwsmmio->rstc);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dw_spi_mmio_remove(struct platform_device *pdev)
|
|
{
|
|
struct dw_spi_mmio *dwsmmio = platform_get_drvdata(pdev);
|
|
|
|
dw_spi_remove_host(&dwsmmio->dws);
|
|
pm_runtime_disable(&pdev->dev);
|
|
clk_disable_unprepare(dwsmmio->pclk);
|
|
clk_disable_unprepare(dwsmmio->clk);
|
|
reset_control_assert(dwsmmio->rstc);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct of_device_id dw_spi_mmio_of_match[] = {
|
|
{ .compatible = "snps,dw-apb-ssi", .data = dw_spi_dw_apb_init},
|
|
{ .compatible = "mscc,ocelot-spi", .data = dw_spi_mscc_ocelot_init},
|
|
{ .compatible = "mscc,jaguar2-spi", .data = dw_spi_mscc_jaguar2_init},
|
|
{ .compatible = "amazon,alpine-dw-apb-ssi", .data = dw_spi_alpine_init},
|
|
{ .compatible = "renesas,rzn1-spi", .data = dw_spi_dw_apb_init},
|
|
{ .compatible = "snps,dwc-ssi-1.01a", .data = dw_spi_dwc_ssi_init},
|
|
{ .compatible = "intel,keembay-ssi", .data = dw_spi_keembay_init},
|
|
{ .compatible = "microchip,sparx5-spi", dw_spi_mscc_sparx5_init},
|
|
{ /* end of table */}
|
|
};
|
|
MODULE_DEVICE_TABLE(of, dw_spi_mmio_of_match);
|
|
|
|
#ifdef CONFIG_ACPI
|
|
static const struct acpi_device_id dw_spi_mmio_acpi_match[] = {
|
|
{"HISI0173", (kernel_ulong_t)dw_spi_dw_apb_init},
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(acpi, dw_spi_mmio_acpi_match);
|
|
#endif
|
|
|
|
static struct platform_driver dw_spi_mmio_driver = {
|
|
.probe = dw_spi_mmio_probe,
|
|
.remove = dw_spi_mmio_remove,
|
|
.driver = {
|
|
.name = DRIVER_NAME,
|
|
.of_match_table = dw_spi_mmio_of_match,
|
|
.acpi_match_table = ACPI_PTR(dw_spi_mmio_acpi_match),
|
|
},
|
|
};
|
|
module_platform_driver(dw_spi_mmio_driver);
|
|
|
|
MODULE_AUTHOR("Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>");
|
|
MODULE_DESCRIPTION("Memory-mapped I/O interface driver for DW SPI Core");
|
|
MODULE_LICENSE("GPL v2");
|