2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-25 21:54:06 +08:00
linux-next/drivers/infiniband/ulp/ipoib
Mark Bloch 492a7e67ff IB/IPoIB: Allow setting the device address
In IB networks, and specifically in IPoIB/rdmacm traffic, the device
address of an IPoIB interface is used as a means to exchange information
between nodes needed for communication.

Currently an IPoIB interface will always be created with a device
address based on its node GUID without a way to change that.

This change adds the ability to set the device address of an IPoIB
interface by value. We use the set mac address ndo to do that.

The flow should be broken down to two:
1) The GID value is already in the GID table,
   in this case the interface will be able to set carrier up.

2) The GID value is not yet in the GID table,
   in this case the interface won't try to join the multicast group
   and will wait (listen on GID_CHANGE event) until the GID is inserted.

In order to track those changes, we add a new flag:
* IPOIB_FLAG_DEV_ADDR_SET.

When set, it means the dev_addr is a based on a value in the gid
table. this bit will be cleared upon a dev_addr change triggered
by the user and set after validation.

Per IB spec the port GUID can't change if the module is loaded.
port GUID is the basis for GID at index 0 which is the basis for
the default device address of a ipoib interface.

The issue is that there are devices that don't follow the spec,
they change the port GUID while HCA is powered on, so in order
not to break userspace applications. We need to check if the
user wanted to control the device address and we assume that
if he sets the device address back to be based on GID index 0,
he no longer wishs to control it.

In order to track this, we add an additional flag:
* IPOIB_FLAG_DEV_ADDR_CTRL

When setting the device address, there is no validation of the upper
twelve bytes of the device address (flags, qpn, subnet prefix) as those
bytes are not under the control of the user.

Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
2016-05-25 15:39:03 -04:00
..
ipoib_cm.c IB/ipoib: Add handling for sending of skb with many frags 2016-03-03 09:49:44 -05:00
ipoib_ethtool.c IB/ipoib: Add readout of statistics using ethtool 2016-05-13 19:39:43 -04:00
ipoib_fs.c IPoIB: Remove unnecessary test for NULL before debugfs_remove() 2014-08-12 21:59:54 -07:00
ipoib_ib.c IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
ipoib_main.c IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
ipoib_multicast.c IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
ipoib_netlink.c infiniband: make sure the src net is infiniband when create new link 2014-01-03 20:38:56 -05:00
ipoib_verbs.c IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
ipoib_vlan.c IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
ipoib.h IB/IPoIB: Allow setting the device address 2016-05-25 15:39:03 -04:00
Kconfig kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT 2011-01-20 17:02:05 -08:00
Makefile IB/ipoib: Add rtnl_link_ops support 2012-09-20 16:49:17 -04:00