2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-25 21:54:06 +08:00
linux-next/drivers/bluetooth/btmrvl_sdio.h
Xinming Hu bb7f4f0bce btmrvl: add platform specific wakeup interrupt support
On some arm-based platforms, we need to configure platform specific
parameters by device tree node and also define our node as a child
node of parent SDIO host controller.
This patch parses these parameters from device tree. It includes
calibration data download to firmware, wakeup pin configured to firmware,
and soc specific wake up gpio, which will be set as wakeup interrupt pin.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-05-02 19:26:15 +02:00

129 lines
3.3 KiB
C

/**
* Marvell BT-over-SDIO driver: SDIO interface related definitions
*
* Copyright (C) 2009, Marvell International Ltd.
*
* This software file (the "File") is distributed by Marvell International
* Ltd. under the terms of the GNU General Public License Version 2, June 1991
* (the "License"). You may use, redistribute and/or modify this File in
* accordance with the terms and conditions of the License, a copy of which
* is available by writing to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA or on the
* worldwide web at http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
*
*
* THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
* IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
* ARE EXPRESSLY DISCLAIMED. The License provides additional details about
* this warranty disclaimer.
*
**/
#define SDIO_HEADER_LEN 4
/* SD block size can not bigger than 64 due to buf size limit in firmware */
/* define SD block size for data Tx/Rx */
#define SDIO_BLOCK_SIZE 64
/* Number of blocks for firmware transfer */
#define FIRMWARE_TRANSFER_NBLOCK 2
/* This is for firmware specific length */
#define FW_EXTRA_LEN 36
#define MRVDRV_SIZE_OF_CMD_BUFFER (2 * 1024)
#define MRVDRV_BT_RX_PACKET_BUFFER_SIZE \
(HCI_MAX_FRAME_SIZE + FW_EXTRA_LEN)
#define ALLOC_BUF_SIZE (((max_t (int, MRVDRV_BT_RX_PACKET_BUFFER_SIZE, \
MRVDRV_SIZE_OF_CMD_BUFFER) + SDIO_HEADER_LEN \
+ SDIO_BLOCK_SIZE - 1) / SDIO_BLOCK_SIZE) \
* SDIO_BLOCK_SIZE)
/* The number of times to try when polling for status */
#define MAX_POLL_TRIES 100
/* Max retry number of CMD53 write */
#define MAX_WRITE_IOMEM_RETRY 2
/* register bitmasks */
#define HOST_POWER_UP BIT(1)
#define HOST_CMD53_FIN BIT(2)
#define HIM_DISABLE 0xff
#define HIM_ENABLE (BIT(0) | BIT(1))
#define UP_LD_HOST_INT_STATUS BIT(0)
#define DN_LD_HOST_INT_STATUS BIT(1)
#define DN_LD_CARD_RDY BIT(0)
#define CARD_IO_READY BIT(3)
#define FIRMWARE_READY 0xfedc
struct btmrvl_plt_wake_cfg {
int irq_bt;
bool wake_by_bt;
};
struct btmrvl_sdio_card_reg {
u8 cfg;
u8 host_int_mask;
u8 host_intstatus;
u8 card_status;
u8 sq_read_base_addr_a0;
u8 sq_read_base_addr_a1;
u8 card_revision;
u8 card_fw_status0;
u8 card_fw_status1;
u8 card_rx_len;
u8 card_rx_unit;
u8 io_port_0;
u8 io_port_1;
u8 io_port_2;
bool int_read_to_clear;
u8 host_int_rsr;
u8 card_misc_cfg;
u8 fw_dump_ctrl;
u8 fw_dump_start;
u8 fw_dump_end;
};
struct btmrvl_sdio_card {
struct sdio_func *func;
u32 ioport;
const char *helper;
const char *firmware;
const struct btmrvl_sdio_card_reg *reg;
bool support_pscan_win_report;
bool supports_fw_dump;
u16 sd_blksz_fw_dl;
u8 rx_unit;
struct btmrvl_private *priv;
struct device_node *plt_of_node;
struct btmrvl_plt_wake_cfg *plt_wake_cfg;
};
struct btmrvl_sdio_device {
const char *helper;
const char *firmware;
const struct btmrvl_sdio_card_reg *reg;
const bool support_pscan_win_report;
u16 sd_blksz_fw_dl;
bool supports_fw_dump;
};
/* Platform specific DMA alignment */
#define BTSDIO_DMA_ALIGN 8
/* Macros for Data Alignment : size */
#define ALIGN_SZ(p, a) \
(((p) + ((a) - 1)) & ~((a) - 1))
/* Macros for Data Alignment : address */
#define ALIGN_ADDR(p, a) \
((((unsigned long)(p)) + (((unsigned long)(a)) - 1)) & \
~(((unsigned long)(a)) - 1))