mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-21 19:53:59 +08:00
71b149b3f7
There is no need to pinmux the UART so early in the kernel. Move it to the board init. This will also allow to finally move the gpio driver to platform device/driver. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
450 lines
10 KiB
C
450 lines
10 KiB
C
/*
|
|
* linux/arch/arm/mach-at91/board-sam9263ek.c
|
|
*
|
|
* Copyright (C) 2005 SAN People
|
|
* Copyright (C) 2007 Atmel Corporation.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/init.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/ads7846.h>
|
|
#include <linux/i2c/at24.h>
|
|
#include <linux/fb.h>
|
|
#include <linux/gpio_keys.h>
|
|
#include <linux/input.h>
|
|
#include <linux/leds.h>
|
|
|
|
#include <video/atmel_lcdc.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/irq.h>
|
|
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/irq.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <mach/board.h>
|
|
#include <mach/at91sam9_smc.h>
|
|
#include <mach/at91_shdwc.h>
|
|
#include <mach/system_rev.h>
|
|
|
|
#include "sam9_smc.h"
|
|
#include "generic.h"
|
|
|
|
|
|
static void __init ek_init_early(void)
|
|
{
|
|
/* Initialize processor: 16.367 MHz crystal */
|
|
at91_initialize(16367660);
|
|
}
|
|
|
|
/*
|
|
* USB Host port
|
|
*/
|
|
static struct at91_usbh_data __initdata ek_usbh_data = {
|
|
.ports = 2,
|
|
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
|
|
.vbus_pin_active_low = {1, 1},
|
|
.overcurrent_pin= {-EINVAL, -EINVAL},
|
|
};
|
|
|
|
/*
|
|
* USB Device port
|
|
*/
|
|
static struct at91_udc_data __initdata ek_udc_data = {
|
|
.vbus_pin = AT91_PIN_PA25,
|
|
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
|
|
};
|
|
|
|
|
|
/*
|
|
* ADS7846 Touchscreen
|
|
*/
|
|
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
|
|
static int ads7843_pendown_state(void)
|
|
{
|
|
return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
|
|
}
|
|
|
|
static struct ads7846_platform_data ads_info = {
|
|
.model = 7843,
|
|
.x_min = 150,
|
|
.x_max = 3830,
|
|
.y_min = 190,
|
|
.y_max = 3830,
|
|
.vref_delay_usecs = 100,
|
|
.x_plate_ohms = 450,
|
|
.y_plate_ohms = 250,
|
|
.pressure_max = 15000,
|
|
.debounce_max = 1,
|
|
.debounce_rep = 0,
|
|
.debounce_tol = (~0),
|
|
.get_pendown_state = ads7843_pendown_state,
|
|
};
|
|
|
|
static void __init ek_add_device_ts(void)
|
|
{
|
|
at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
|
|
at91_set_gpio_input(AT91_PIN_PA31, 1); /* Touchscreen BUSY signal */
|
|
}
|
|
#else
|
|
static void __init ek_add_device_ts(void) {}
|
|
#endif
|
|
|
|
/*
|
|
* SPI devices.
|
|
*/
|
|
static struct spi_board_info ek_spi_devices[] = {
|
|
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
|
|
{ /* DataFlash card */
|
|
.modalias = "mtd_dataflash",
|
|
.chip_select = 0,
|
|
.max_speed_hz = 15 * 1000 * 1000,
|
|
.bus_num = 0,
|
|
},
|
|
#endif
|
|
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
|
|
{
|
|
.modalias = "ads7846",
|
|
.chip_select = 3,
|
|
.max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
|
|
.bus_num = 0,
|
|
.platform_data = &ads_info,
|
|
.irq = AT91SAM9263_ID_IRQ1,
|
|
},
|
|
#endif
|
|
};
|
|
|
|
|
|
/*
|
|
* MCI (SD/MMC)
|
|
*/
|
|
static struct at91_mmc_data __initdata ek_mmc_data = {
|
|
.wire4 = 1,
|
|
.det_pin = AT91_PIN_PE18,
|
|
.wp_pin = AT91_PIN_PE19,
|
|
.vcc_pin = -EINVAL,
|
|
};
|
|
|
|
|
|
/*
|
|
* MACB Ethernet device
|
|
*/
|
|
static struct macb_platform_data __initdata ek_macb_data = {
|
|
.phy_irq_pin = AT91_PIN_PE31,
|
|
.is_rmii = 1,
|
|
};
|
|
|
|
|
|
/*
|
|
* NAND flash
|
|
*/
|
|
static struct mtd_partition __initdata ek_nand_partition[] = {
|
|
{
|
|
.name = "Partition 1",
|
|
.offset = 0,
|
|
.size = SZ_64M,
|
|
},
|
|
{
|
|
.name = "Partition 2",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
static struct atmel_nand_data __initdata ek_nand_data = {
|
|
.ale = 21,
|
|
.cle = 22,
|
|
.det_pin = -EINVAL,
|
|
.rdy_pin = AT91_PIN_PA22,
|
|
.enable_pin = AT91_PIN_PD15,
|
|
.ecc_mode = NAND_ECC_SOFT,
|
|
.on_flash_bbt = 1,
|
|
.parts = ek_nand_partition,
|
|
.num_parts = ARRAY_SIZE(ek_nand_partition),
|
|
};
|
|
|
|
static struct sam9_smc_config __initdata ek_nand_smc_config = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 1,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 1,
|
|
|
|
.ncs_read_pulse = 3,
|
|
.nrd_pulse = 3,
|
|
.ncs_write_pulse = 3,
|
|
.nwe_pulse = 3,
|
|
|
|
.read_cycle = 5,
|
|
.write_cycle = 5,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
|
|
.tdf_cycles = 2,
|
|
};
|
|
|
|
static void __init ek_add_device_nand(void)
|
|
{
|
|
ek_nand_data.bus_width_16 = board_have_nand_16bit();
|
|
/* setup bus-width (8 or 16) */
|
|
if (ek_nand_data.bus_width_16)
|
|
ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
|
|
else
|
|
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
|
|
|
|
/* configure chip-select 3 (NAND) */
|
|
sam9_smc_configure(0, 3, &ek_nand_smc_config);
|
|
|
|
at91_add_device_nand(&ek_nand_data);
|
|
}
|
|
|
|
|
|
/*
|
|
* I2C devices
|
|
*/
|
|
static struct at24_platform_data at24c512 = {
|
|
.byte_len = SZ_512K / 8,
|
|
.page_size = 128,
|
|
.flags = AT24_FLAG_ADDR16,
|
|
};
|
|
|
|
|
|
static struct i2c_board_info __initdata ek_i2c_devices[] = {
|
|
{
|
|
I2C_BOARD_INFO("24c512", 0x50),
|
|
.platform_data = &at24c512,
|
|
},
|
|
/* more devices can be added using expansion connectors */
|
|
};
|
|
|
|
/*
|
|
* LCD Controller
|
|
*/
|
|
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
|
|
static struct fb_videomode at91_tft_vga_modes[] = {
|
|
{
|
|
.name = "TX09D50VM1CCA @ 60",
|
|
.refresh = 60,
|
|
.xres = 240, .yres = 320,
|
|
.pixclock = KHZ2PICOS(4965),
|
|
|
|
.left_margin = 1, .right_margin = 33,
|
|
.upper_margin = 1, .lower_margin = 0,
|
|
.hsync_len = 5, .vsync_len = 1,
|
|
|
|
.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
|
|
.vmode = FB_VMODE_NONINTERLACED,
|
|
},
|
|
};
|
|
|
|
static struct fb_monspecs at91fb_default_monspecs = {
|
|
.manufacturer = "HIT",
|
|
.monitor = "TX09D70VM1CCA",
|
|
|
|
.modedb = at91_tft_vga_modes,
|
|
.modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
|
|
.hfmin = 15000,
|
|
.hfmax = 64000,
|
|
.vfmin = 50,
|
|
.vfmax = 150,
|
|
};
|
|
|
|
#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
|
|
| ATMEL_LCDC_DISTYPE_TFT \
|
|
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
|
|
|
|
static void at91_lcdc_power_control(int on)
|
|
{
|
|
at91_set_gpio_value(AT91_PIN_PA30, on);
|
|
}
|
|
|
|
/* Driver datas */
|
|
static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
|
|
.lcdcon_is_backlight = true,
|
|
.default_bpp = 16,
|
|
.default_dmacon = ATMEL_LCDC_DMAEN,
|
|
.default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
|
|
.default_monspecs = &at91fb_default_monspecs,
|
|
.atmel_lcdfb_power_control = at91_lcdc_power_control,
|
|
.guard_time = 1,
|
|
};
|
|
|
|
#else
|
|
static struct atmel_lcdfb_info __initdata ek_lcdc_data;
|
|
#endif
|
|
|
|
|
|
/*
|
|
* GPIO Buttons
|
|
*/
|
|
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
|
static struct gpio_keys_button ek_buttons[] = {
|
|
{ /* BP1, "leftclic" */
|
|
.code = BTN_LEFT,
|
|
.gpio = AT91_PIN_PC5,
|
|
.active_low = 1,
|
|
.desc = "left_click",
|
|
.wakeup = 1,
|
|
},
|
|
{ /* BP2, "rightclic" */
|
|
.code = BTN_RIGHT,
|
|
.gpio = AT91_PIN_PC4,
|
|
.active_low = 1,
|
|
.desc = "right_click",
|
|
.wakeup = 1,
|
|
}
|
|
};
|
|
|
|
static struct gpio_keys_platform_data ek_button_data = {
|
|
.buttons = ek_buttons,
|
|
.nbuttons = ARRAY_SIZE(ek_buttons),
|
|
};
|
|
|
|
static struct platform_device ek_button_device = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.num_resources = 0,
|
|
.dev = {
|
|
.platform_data = &ek_button_data,
|
|
}
|
|
};
|
|
|
|
static void __init ek_add_device_buttons(void)
|
|
{
|
|
at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */
|
|
at91_set_deglitch(AT91_PIN_PC5, 1);
|
|
at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */
|
|
at91_set_deglitch(AT91_PIN_PC4, 1);
|
|
|
|
platform_device_register(&ek_button_device);
|
|
}
|
|
#else
|
|
static void __init ek_add_device_buttons(void) {}
|
|
#endif
|
|
|
|
|
|
/*
|
|
* AC97
|
|
* reset_pin is not connected: NRST
|
|
*/
|
|
static struct ac97c_platform_data ek_ac97_data = {
|
|
.reset_pin = -EINVAL,
|
|
};
|
|
|
|
|
|
/*
|
|
* LEDs ... these could all be PWM-driven, for variable brightness
|
|
*/
|
|
static struct gpio_led ek_leds[] = {
|
|
{ /* "right" led, green, userled2 (could be driven by pwm2) */
|
|
.name = "ds2",
|
|
.gpio = AT91_PIN_PC29,
|
|
.active_low = 1,
|
|
.default_trigger = "nand-disk",
|
|
},
|
|
{ /* "power" led, yellow (could be driven by pwm0) */
|
|
.name = "ds3",
|
|
.gpio = AT91_PIN_PB7,
|
|
.default_trigger = "heartbeat",
|
|
}
|
|
};
|
|
|
|
/*
|
|
* PWM Leds
|
|
*/
|
|
static struct gpio_led ek_pwm_led[] = {
|
|
/* For now only DS1 is PWM-driven (by pwm1) */
|
|
{
|
|
.name = "ds1",
|
|
.gpio = 1, /* is PWM channel number */
|
|
.active_low = 1,
|
|
.default_trigger = "none",
|
|
}
|
|
};
|
|
|
|
/*
|
|
* CAN
|
|
*/
|
|
static void sam9263ek_transceiver_switch(int on)
|
|
{
|
|
if (on) {
|
|
at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
|
|
at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
|
|
} else {
|
|
at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
|
|
at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
|
|
}
|
|
}
|
|
|
|
static struct at91_can_data ek_can_data = {
|
|
.transceiver_switch = sam9263ek_transceiver_switch,
|
|
};
|
|
|
|
static void __init ek_board_init(void)
|
|
{
|
|
/* Serial */
|
|
/* DBGU on ttyS0. (Rx & Tx only) */
|
|
at91_register_uart(0, 0, 0);
|
|
|
|
/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
|
|
at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
|
|
at91_add_device_serial();
|
|
/* USB Host */
|
|
at91_add_device_usbh(&ek_usbh_data);
|
|
/* USB Device */
|
|
at91_add_device_udc(&ek_udc_data);
|
|
/* SPI */
|
|
at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
|
|
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
|
|
/* Touchscreen */
|
|
ek_add_device_ts();
|
|
/* MMC */
|
|
at91_add_device_mmc(1, &ek_mmc_data);
|
|
/* Ethernet */
|
|
at91_add_device_eth(&ek_macb_data);
|
|
/* NAND */
|
|
ek_add_device_nand();
|
|
/* I2C */
|
|
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
|
|
/* LCD Controller */
|
|
at91_add_device_lcdc(&ek_lcdc_data);
|
|
/* Push Buttons */
|
|
ek_add_device_buttons();
|
|
/* AC97 */
|
|
at91_add_device_ac97(&ek_ac97_data);
|
|
/* LEDs */
|
|
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
|
|
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
|
|
/* CAN */
|
|
at91_add_device_can(&ek_can_data);
|
|
}
|
|
|
|
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
|
|
/* Maintainer: Atmel */
|
|
.timer = &at91sam926x_timer,
|
|
.map_io = at91_map_io,
|
|
.init_early = ek_init_early,
|
|
.init_irq = at91_init_irq_default,
|
|
.init_machine = ek_board_init,
|
|
MACHINE_END
|