mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-21 11:44:01 +08:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
64 lines
2.7 KiB
Plaintext
64 lines
2.7 KiB
Plaintext
Text File for the COPS LocalTalk Linux driver (cops.c).
|
|
By Jay Schulist <jschlst@samba.org>
|
|
|
|
This driver has two modes and they are: Dayna mode and Tangent mode.
|
|
Each mode corresponds with the type of card. It has been found
|
|
that there are 2 main types of cards and all other cards are
|
|
the same and just have different names or only have minor differences
|
|
such as more IO ports. As this driver is tested it will
|
|
become more clear exactly what cards are supported.
|
|
|
|
Right now these cards are known to work with the COPS driver. The
|
|
LT-200 cards work in a somewhat more limited capacity than the
|
|
DL200 cards, which work very well and are in use by many people.
|
|
|
|
TANGENT driver mode:
|
|
Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200
|
|
DAYNA driver mode:
|
|
Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95,
|
|
Farallon PhoneNET PC III, Farallon PhoneNET PC II
|
|
Other cards possibly supported mode unknown though:
|
|
Dayna DL2000 (Full length)
|
|
|
|
The COPS driver defaults to using Dayna mode. To change the driver's
|
|
mode if you built a driver with dual support use board_type=1 or
|
|
board_type=2 for Dayna or Tangent with insmod.
|
|
|
|
** Operation/loading of the driver.
|
|
Use modprobe like this: /sbin/modprobe cops.o (IO #) (IRQ #)
|
|
If you do not specify any options the driver will try and use the IO = 0x240,
|
|
IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing.
|
|
|
|
To load multiple COPS driver Localtalk cards you can do one of the following.
|
|
|
|
insmod cops io=0x240 irq=5
|
|
insmod -o cops2 cops io=0x260 irq=3
|
|
|
|
Or in lilo.conf put something like this:
|
|
append="ether=5,0x240,lt0 ether=3,0x260,lt1"
|
|
|
|
Then bring up the interface with ifconfig. It will look something like this:
|
|
lt0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00
|
|
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
|
|
UP BROADCAST RUNNING NOARP MULTICAST MTU:600 Metric:1
|
|
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
|
|
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0
|
|
|
|
** Netatalk Configuration
|
|
You will need to configure atalkd with something like the following to make
|
|
it work with the cops.c driver.
|
|
|
|
* For single LTalk card use.
|
|
dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033"
|
|
lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
|
|
|
|
* For multiple cards, Ethernet and LocalTalk.
|
|
eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033"
|
|
lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
|
|
|
|
* For multiple LocalTalk cards, and an Ethernet card.
|
|
* Order seems to matter here, Ethernet last.
|
|
lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1"
|
|
lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2"
|
|
eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk"
|