mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 06:34:11 +08:00
8ffaeaf42e
This patch removes a limitation of the original code, so that CHASSIS codes can be sent to all machines. On machines with a LCD panel, this code displays "INI" during bootup, "RUN" when the system is booted and running, "FLT" when a panic occurs, etc. This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS This patch also adds minimalistic support for Chassis warnings, through a proc entry '/proc/chassis', which will reflect the warnings status (PSU or fans failure when they happen, NVRAM battery level and temperature thresholds overflows). This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS_WARN Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org> Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
189 lines
5.4 KiB
Plaintext
189 lines
5.4 KiB
Plaintext
menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)"
|
|
|
|
config GSC
|
|
bool "VSC/GSC/HSC bus support"
|
|
default y
|
|
help
|
|
The VSC, GSC and HSC busses were used from the earliest 700-series
|
|
workstations up to and including the C360/J2240 workstations. They
|
|
were also used in servers from the E-class to the K-class. They
|
|
are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards.
|
|
If in doubt, say "Y".
|
|
|
|
config HPPB
|
|
bool "HP-PB bus support"
|
|
depends on GSC
|
|
help
|
|
The HP-PB bus was used in the Nova class and K-class servers.
|
|
If in doubt, say "Y"
|
|
|
|
config IOMMU_CCIO
|
|
bool "U2/Uturn I/O MMU"
|
|
depends on GSC
|
|
help
|
|
Say Y here to enable DMA management routines for the first
|
|
generation of PA-RISC cache-coherent machines. Programs the
|
|
U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
|
|
|
|
config GSC_LASI
|
|
bool "Lasi I/O support"
|
|
depends on GSC
|
|
help
|
|
Say Y here to support the Lasi multifunction chip found in
|
|
many PA-RISC workstations & servers. It includes interfaces
|
|
for a parallel port, serial port, NCR 53c710 SCSI, Apricot
|
|
Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony
|
|
and floppy. Note that you must still enable all the individual
|
|
drivers for these chips.
|
|
|
|
config GSC_WAX
|
|
bool "Wax I/O support"
|
|
depends on GSC
|
|
help
|
|
Say Y here to support the Wax multifunction chip found in some
|
|
older systems, including B/C/D/R class and 715/64, 715/80 and
|
|
715/100. Wax includes an EISA adapter, a serial port (not always
|
|
used), a HIL interface chip and is also known to be used as the
|
|
GSC bridge for an X.25 GSC card.
|
|
|
|
config EISA
|
|
bool "EISA support"
|
|
depends on GSC
|
|
help
|
|
Say Y here if you have an EISA bus in your machine. This code
|
|
supports both the Mongoose & Wax EISA adapters. It is sadly
|
|
incomplete and lacks support for card-to-host DMA.
|
|
|
|
source "drivers/eisa/Kconfig"
|
|
|
|
config ISA
|
|
bool "ISA support"
|
|
depends on EISA
|
|
help
|
|
If you want to plug an ISA card into your EISA bus, say Y here.
|
|
Most people should say N.
|
|
|
|
config PCI
|
|
bool "PCI support"
|
|
help
|
|
All recent HP machines have PCI slots, and you should say Y here
|
|
if you have a recent machine. If you are convinced you do not have
|
|
PCI slots in your machine (eg a 712), then you may say "N" here.
|
|
Beware that some GSC cards have a Dino onboard and PCI inside them,
|
|
so it may be safest to say "Y" anyway.
|
|
|
|
source "drivers/pci/Kconfig"
|
|
|
|
config GSC_DINO
|
|
bool "GSCtoPCI/Dino PCI support"
|
|
depends on PCI && GSC
|
|
help
|
|
Say Y here to support the Dino & Cujo GSC to PCI bridges found in
|
|
machines from the B132 to the C360, the J2240 and the A180. Some
|
|
GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on
|
|
the card, and you also need to say Y here if you have such a card.
|
|
Note that Dino also supplies one of the serial ports on certain
|
|
machines. If in doubt, say Y.
|
|
|
|
config PCI_LBA
|
|
bool "LBA/Elroy PCI support"
|
|
depends on PCI
|
|
help
|
|
Say Y here to support the Elroy PCI Lower Bus Adapter. This is
|
|
present on B, C, J, L and N-class machines with 4-digit model
|
|
numbers and the A400/A500.
|
|
|
|
config IOSAPIC
|
|
bool
|
|
depends on PCI_LBA
|
|
default PCI_LBA
|
|
|
|
config IOMMU_SBA
|
|
bool
|
|
depends on PCI_LBA
|
|
default PCI_LBA
|
|
|
|
#config PCI_EPIC
|
|
# bool "EPIC/SAGA PCI support"
|
|
# depends on PCI
|
|
# default y
|
|
# help
|
|
# Say Y here for V-class PCI, DMA/IOMMU, IRQ subsystem support.
|
|
|
|
source "drivers/pcmcia/Kconfig"
|
|
|
|
source "drivers/pci/hotplug/Kconfig"
|
|
|
|
endmenu
|
|
|
|
menu "PA-RISC specific drivers"
|
|
|
|
config SUPERIO
|
|
bool "SuperIO (SuckyIO) support"
|
|
depends on PCI_LBA
|
|
default y
|
|
help
|
|
Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and
|
|
J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and
|
|
Serial port on those machines.
|
|
|
|
config CHASSIS_LCD_LED
|
|
bool "Chassis LCD and LED support"
|
|
default y
|
|
help
|
|
Say Y here if you want to enable support for the Heartbeat,
|
|
Disk/Network activities LEDs on some PA-RISC machines,
|
|
or support for the LCD that can be found on recent material.
|
|
|
|
This has nothing to do with LED State support for A and E class.
|
|
|
|
If unsure, say Y.
|
|
|
|
config PDC_CHASSIS
|
|
bool "PDC chassis state codes support"
|
|
default y
|
|
help
|
|
Say Y here if you want to enable support for Chassis codes.
|
|
That includes support for LED State front panel as found on E
|
|
class, and support for the GSP Virtual Front Panel (LED State and
|
|
message logging) as found on high end servers such as A, L and
|
|
N-class.
|
|
This driver will also display progress messages on LCD display,
|
|
such as "INI", "RUN" and "FLT", and might thus clobber messages
|
|
shown by the LED/LCD driver.
|
|
This driver updates the state panel (LED and/or LCD) upon system
|
|
state change (eg: boot, shutdown or panic).
|
|
|
|
If unsure, say Y.
|
|
|
|
|
|
config PDC_CHASSIS_WARN
|
|
bool "PDC chassis warnings support"
|
|
depends on PROC_FS
|
|
default y
|
|
help
|
|
Say Y here if you want to enable support for Chassis warnings.
|
|
This will add a proc entry '/proc/chassis' giving some information
|
|
about the overall health state of the system.
|
|
This includes NVRAM battery level, overtemp or failures such as
|
|
fans or power units.
|
|
|
|
If unsure, say Y.
|
|
|
|
|
|
config PDC_STABLE
|
|
tristate "PDC Stable Storage support"
|
|
depends on SYSFS
|
|
default y
|
|
help
|
|
Say Y here if you want to enable support for accessing Stable Storage
|
|
variables (PDC non volatile variables such as Primary Boot Path,
|
|
Console Path, Autoboot, Autosearch, etc) through SysFS.
|
|
|
|
If unsure, say Y.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
The module will be called pdc_stable.
|
|
|
|
endmenu
|