mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-28 23:23:55 +08:00
328e3e369b
Now with the varity of several RPi boards, the memory should be defined at board level. This step gives us the chance to fix the memory size of the RPi 1 B+, Zero (incl. W) and Compute Module 1. Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Acked-by: Eric Anholt <eric@anholt.net>
177 lines
3.2 KiB
Plaintext
177 lines
3.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/dts-v1/;
|
|
#include "bcm2837.dtsi"
|
|
#include "bcm2836-rpi.dtsi"
|
|
#include "bcm283x-rpi-usb-host.dtsi"
|
|
|
|
/ {
|
|
compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
|
|
model = "Raspberry Pi 3 Model A+";
|
|
|
|
chosen {
|
|
/* 8250 auxiliary UART instead of pl011 */
|
|
stdout-path = "serial1:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0 0x20000000>;
|
|
};
|
|
|
|
leds {
|
|
act {
|
|
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
pwr {
|
|
label = "PWR";
|
|
gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&firmware {
|
|
expgpio: gpio {
|
|
compatible = "raspberrypi,firmware-gpio";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-line-names = "",
|
|
"BT_WL_ON",
|
|
"STATUS_LED_R",
|
|
"",
|
|
"",
|
|
"CAM_GPIO0",
|
|
"CAM_GPIO1",
|
|
"";
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
/*
|
|
* This is mostly based on the official GPU firmware DT blob.
|
|
*
|
|
* Legend:
|
|
* "NC" = not connected (no rail from the SoC)
|
|
* "FOO" = GPIO line named "FOO" on the schematic
|
|
* "FOO_N" = GPIO line named "FOO" on schematic, active low
|
|
*/
|
|
gpio-line-names = "ID_SDA",
|
|
"ID_SCL",
|
|
"SDA1",
|
|
"SCL1",
|
|
"GPIO_GCLK",
|
|
"GPIO5",
|
|
"GPIO6",
|
|
"SPI_CE1_N",
|
|
"SPI_CE0_N",
|
|
"SPI_MISO",
|
|
"SPI_MOSI",
|
|
"SPI_SCLK",
|
|
"GPIO12",
|
|
"GPIO13",
|
|
/* Serial port */
|
|
"TXD1",
|
|
"RXD1",
|
|
"GPIO16",
|
|
"GPIO17",
|
|
"GPIO18",
|
|
"GPIO19",
|
|
"GPIO20",
|
|
"GPIO21",
|
|
"GPIO22",
|
|
"GPIO23",
|
|
"GPIO24",
|
|
"GPIO25",
|
|
"GPIO26",
|
|
"GPIO27",
|
|
"HDMI_HPD_N",
|
|
"STATUS_LED_G",
|
|
/* Used by BT module */
|
|
"CTS0",
|
|
"RTS0",
|
|
"TXD0",
|
|
"RXD0",
|
|
/* Used by Wifi */
|
|
"SD1_CLK",
|
|
"SD1_CMD",
|
|
"SD1_DATA0",
|
|
"SD1_DATA1",
|
|
"SD1_DATA2",
|
|
"SD1_DATA3",
|
|
"PWM0_OUT",
|
|
"PWM1_OUT",
|
|
"", /* GPIO42 */
|
|
"WIFI_CLK",
|
|
"SDA0",
|
|
"SCL0",
|
|
"SMPS_SCL",
|
|
"SMPS_SDA",
|
|
/* Used by SD Card */
|
|
"SD_CLK_R",
|
|
"SD_CMD_R",
|
|
"SD_DATA0_R",
|
|
"SD_DATA1_R",
|
|
"SD_DATA2_R",
|
|
"SD_DATA3_R";
|
|
};
|
|
|
|
&hdmi {
|
|
hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&pwm {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
* SDHCI is used to control the SDIO for wireless
|
|
*
|
|
* WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
|
|
* by a single GPIO. We can't give GPIO control to one of the drivers,
|
|
* otherwise the other part would get unexpectedly disturbed.
|
|
*/
|
|
&sdhci {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&emmc_gpio34>;
|
|
status = "okay";
|
|
bus-width = <4>;
|
|
non-removable;
|
|
|
|
brcmf: wifi@1 {
|
|
reg = <1>;
|
|
compatible = "brcm,bcm4329-fmac";
|
|
};
|
|
};
|
|
|
|
/* SDHOST is used to drive the SD card */
|
|
&sdhost {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdhost_gpio48>;
|
|
status = "okay";
|
|
bus-width = <4>;
|
|
};
|
|
|
|
/* uart0 communicates with the BT module */
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
|
|
status = "okay";
|
|
|
|
bluetooth {
|
|
compatible = "brcm,bcm43438-bt";
|
|
max-speed = <2000000>;
|
|
};
|
|
};
|
|
|
|
/* uart1 is mapped to the pin header */
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1_gpio14>;
|
|
status = "okay";
|
|
};
|