mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-27 06:34:11 +08:00
7ed609b002
Switch sama5d3 boards to the new PMC clock bindings. This prevents the wb50n to use the out of spec rate for USART1. Link: https://lore.kernel.org/r/20200110222744.1261464-1-alexandre.belloni@bootlin.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
160 lines
2.4 KiB
Plaintext
160 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* at91-dvk_su60_somc.dtsi - Device Tree file for the DVK SOM60 base board
|
|
*
|
|
* Copyright (C) 2018 Laird,
|
|
* 2018 Ben Whitten <ben.whitten@lairdtech.com>
|
|
*
|
|
*/
|
|
|
|
/ {
|
|
sound {
|
|
compatible = "atmel,asoc-wm8904";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
|
|
|
|
atmel,model = "wm8904 @ DVK-SOM60";
|
|
atmel,audio-routing =
|
|
"Headphone Jack", "HPOUTL",
|
|
"Headphone Jack", "HPOUTR",
|
|
"IN2L", "Line In Jack",
|
|
"IN2R", "Line In Jack",
|
|
"Mic", "MICBIAS",
|
|
"IN1L", "Mic";
|
|
|
|
atmel,ssc-controller = <&ssc0>;
|
|
atmel,audio-codec = <&wm8904>;
|
|
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&mmc0 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
|
|
slot@0 {
|
|
bus-width = <4>;
|
|
cd-gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
|
|
cd-inverted;
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
|
|
spi-flash@0 {
|
|
compatible = "mxicy,mx25u4035", "jedec,spi-nor";
|
|
spi-max-frequency = <33000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
&ssc0 {
|
|
atmel,clk-from-rk-pin;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c0 {
|
|
status = "okay";
|
|
|
|
wm8904: wm8904@1a {
|
|
compatible = "wlf,wm8904";
|
|
reg = <0x1a>;
|
|
clocks = <&pmc PMC_TYPE_SYSTEM 10>;
|
|
clock-names = "mclk";
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
|
|
eeprom@57 {
|
|
compatible = "giantec,gt24c32a", "atmel,24c32";
|
|
reg = <0x57>;
|
|
pagesize = <32>;
|
|
};
|
|
};
|
|
|
|
&usart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usart3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dbgu {
|
|
status = "okay";
|
|
};
|
|
|
|
&pit {
|
|
status = "okay";
|
|
};
|
|
|
|
&adc0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&can1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&macb0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
ethernet-phy@7 {
|
|
reg = <7>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_geth_int>;
|
|
interrupt-parent = <&pioB>;
|
|
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
|
|
txen-skew-ps = <800>;
|
|
txc-skew-ps = <3000>;
|
|
rxdv-skew-ps = <400>;
|
|
rxc-skew-ps = <3000>;
|
|
rxd0-skew-ps = <400>;
|
|
rxd1-skew-ps = <400>;
|
|
rxd2-skew-ps = <400>;
|
|
rxd3-skew-ps = <400>;
|
|
};
|
|
};
|
|
|
|
&macb1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
ethernet-phy@1 {
|
|
reg = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_eth_int>;
|
|
interrupt-parent = <&pioC>;
|
|
interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
|
|
};
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb2 {
|
|
status = "okay";
|
|
};
|
|
|