2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-23 12:43:55 +08:00
linux-next/drivers/phy/broadcom/phy-brcm-usb-init-synopsys.c
Al Cooper 209c805835 phy: usb: Fix incorrect clearing of tca_drv_sel bit in SETUP reg for 7211
The 7211a0 has a tca_drv_sel bit in the USB SETUP register that
should never be enabled. This feature is only used if there is a
USB Type-C PHY, and the 7211 does not have one. If the bit is
enabled, the VBUS signal will never be asserted. In the 7211a0,
the bit was incorrectly defaulted to on so the driver had to clear
the bit. In the 7211c0 the state was inverted so the driver should
no longer clear the bit. This hasn't been a problem because all
current 7211 boards don't use the VBUS signal, but there are some
future customer boards that may use it.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201002190115.48017-1-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-10-28 21:40:56 +05:30

410 lines
12 KiB
C

// SPDX-License-Identifier: GPL-2.0
/* Copyright (c) 2018, Broadcom */
/*
* This module contains USB PHY initialization for power up and S3 resume
* for newer Synopsys based USB hardware first used on the bcm7216.
*/
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/soc/brcmstb/brcmstb.h>
#include "phy-brcm-usb-init.h"
#define PHY_LOCK_TIMEOUT_MS 200
/* Register definitions for syscon piarbctl registers */
#define PIARBCTL_CAM 0x00
#define PIARBCTL_SPLITTER 0x04
#define PIARBCTL_MISC 0x08
#define PIARBCTL_MISC_SECURE_MASK 0x80000000
#define PIARBCTL_MISC_USB_SELECT_MASK 0x40000000
#define PIARBCTL_MISC_USB_4G_SDRAM_MASK 0x20000000
#define PIARBCTL_MISC_USB_PRIORITY_MASK 0x000f0000
#define PIARBCTL_MISC_USB_MEM_PAGE_MASK 0x0000f000
#define PIARBCTL_MISC_CAM1_MEM_PAGE_MASK 0x00000f00
#define PIARBCTL_MISC_CAM0_MEM_PAGE_MASK 0x000000f0
#define PIARBCTL_MISC_SATA_PRIORITY_MASK 0x0000000f
#define PIARBCTL_MISC_USB_ONLY_MASK \
(PIARBCTL_MISC_USB_SELECT_MASK | \
PIARBCTL_MISC_USB_4G_SDRAM_MASK | \
PIARBCTL_MISC_USB_PRIORITY_MASK | \
PIARBCTL_MISC_USB_MEM_PAGE_MASK)
/* Register definitions for the USB CTRL block */
#define USB_CTRL_SETUP 0x00
#define USB_CTRL_SETUP_STRAP_IPP_SEL_MASK 0x02000000
#define USB_CTRL_SETUP_SCB2_EN_MASK 0x00008000
#define USB_CTRL_SETUP_tca_drv_sel_MASK 0x01000000
#define USB_CTRL_SETUP_SCB1_EN_MASK 0x00004000
#define USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK 0x00000200
#define USB_CTRL_SETUP_IPP_MASK 0x00000020
#define USB_CTRL_SETUP_IOC_MASK 0x00000010
#define USB_CTRL_USB_PM 0x04
#define USB_CTRL_USB_PM_USB_PWRDN_MASK 0x80000000
#define USB_CTRL_USB_PM_SOFT_RESET_MASK 0x40000000
#define USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK 0x00800000
#define USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK 0x00400000
#define USB_CTRL_USB_PM_STATUS 0x08
#define USB_CTRL_USB_DEVICE_CTL1 0x10
#define USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK 0x00000003
#define USB_CTRL_TEST_PORT_CTL 0x30
#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK 0x000000ff
#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK 0x0000002e
#define USB_CTRL_TP_DIAG1 0x34
#define USB_CTLR_TP_DIAG1_wake_MASK 0x00000002
#define USB_CTRL_CTLR_CSHCR 0x50
#define USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK 0x00040000
/* Register definitions for the USB_PHY block in 7211b0 */
#define USB_PHY_PLL_CTL 0x00
#define USB_PHY_PLL_CTL_PLL_RESETB_MASK 0x40000000
#define USB_PHY_PLL_LDO_CTL 0x08
#define USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK 0x00000004
#define USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK 0x00000002
#define USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK 0x00000001
#define USB_PHY_UTMI_CTL_1 0x04
#define USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK 0x00000800
#define USB_PHY_UTMI_CTL_1_PHY_MODE_MASK 0x0000000c
#define USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT 2
#define USB_PHY_IDDQ 0x1c
#define USB_PHY_IDDQ_phy_iddq_MASK 0x00000001
#define USB_PHY_STATUS 0x20
#define USB_PHY_STATUS_pll_lock_MASK 0x00000001
/* Register definitions for the MDIO registers in the DWC2 block of
* the 7211b0.
* NOTE: The PHY's MDIO registers are only accessible through the
* legacy DesignWare USB controller even though it's not being used.
*/
#define USB_GMDIOCSR 0
#define USB_GMDIOGEN 4
/* Register definitions for the BDC EC block in 7211b0 */
#define BDC_EC_AXIRDA 0x0c
#define BDC_EC_AXIRDA_RTS_MASK 0xf0000000
#define BDC_EC_AXIRDA_RTS_SHIFT 28
static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params,
uint8_t addr, uint16_t data)
{
void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
addr &= 0x1f; /* 5-bit address */
brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
brcm_usb_writel(0x59020000 | (addr << 18) | data,
usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
}
static uint16_t __maybe_unused usb_mdio_read_7211b0(
struct brcm_usb_init_params *params, uint8_t addr)
{
void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO];
addr &= 0x1f; /* 5-bit address */
brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
brcm_usb_writel(0x69020000 | (addr << 18), usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN);
while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31))
;
return brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & 0xffff;
}
static void usb2_eye_fix_7211b0(struct brcm_usb_init_params *params)
{
/* select bank */
usb_mdio_write_7211b0(params, 0x1f, 0x80a0);
/* Set the eye */
usb_mdio_write_7211b0(params, 0x0a, 0xc6a0);
}
static void xhci_soft_reset(struct brcm_usb_init_params *params,
int on_off)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
/* Assert reset */
if (on_off)
USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB);
/* De-assert reset */
else
USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB);
}
static void usb_init_ipp(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
u32 reg;
u32 orig_reg;
pr_debug("%s\n", __func__);
orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP));
if (params->ipp != 2)
/* override ipp strap pin (if it exits) */
reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL));
/* Override the default OC and PP polarity */
reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC));
if (params->ioc)
reg |= USB_CTRL_MASK(SETUP, IOC);
if (params->ipp == 1)
reg |= USB_CTRL_MASK(SETUP, IPP);
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP));
/*
* If we're changing IPP, make sure power is off long enough
* to turn off any connected devices.
*/
if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP))
msleep(50);
}
static void syscon_piarbctl_init(struct regmap *rmap)
{
/* Switch from legacy USB OTG controller to new STB USB controller */
regmap_update_bits(rmap, PIARBCTL_MISC, PIARBCTL_MISC_USB_ONLY_MASK,
PIARBCTL_MISC_USB_SELECT_MASK |
PIARBCTL_MISC_USB_4G_SDRAM_MASK);
}
static void usb_init_common(struct brcm_usb_init_params *params)
{
u32 reg;
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
pr_debug("%s\n", __func__);
USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
/* 1 millisecond - for USB clocks to settle down */
usleep_range(1000, 2000);
if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) {
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
reg |= params->mode;
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
}
switch (params->mode) {
case USB_CTLR_MODE_HOST:
USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
break;
default:
USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB);
USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB);
break;
}
}
static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params,
bool enable)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
if (enable)
USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en);
else
USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en);
}
static void usb_init_common_7211b0(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
void __iomem *bdc_ec = params->regs[BRCM_REGS_BDC_EC];
int timeout_ms = PHY_LOCK_TIMEOUT_MS;
u32 reg;
if (params->syscon_piarbctl)
syscon_piarbctl_init(params->syscon_piarbctl);
USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN);
usb_wake_enable_7211b0(params, false);
if (!params->wake_enabled) {
/* undo possible suspend settings */
brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ);
reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
/* temporarily enable FSM so PHY comes up properly */
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
}
/* Init the PHY */
reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK |
USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK |
USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL);
/* wait for lock */
while (timeout_ms-- > 0) {
reg = brcm_usb_readl(usb_phy + USB_PHY_STATUS);
if (reg & USB_PHY_STATUS_pll_lock_MASK)
break;
usleep_range(1000, 2000);
}
/* Set the PHY_MODE */
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
reg &= ~USB_PHY_UTMI_CTL_1_PHY_MODE_MASK;
reg |= params->mode << USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT;
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
usb_init_common(params);
/*
* The BDC controller will get occasional failures with
* the default "Read Transaction Size" of 6 (1024 bytes).
* Set it to 4 (256 bytes).
*/
if ((params->mode != USB_CTLR_MODE_HOST) && bdc_ec) {
reg = brcm_usb_readl(bdc_ec + BDC_EC_AXIRDA);
reg &= ~BDC_EC_AXIRDA_RTS_MASK;
reg |= (0x4 << BDC_EC_AXIRDA_RTS_SHIFT);
brcm_usb_writel(reg, bdc_ec + BDC_EC_AXIRDA);
}
/*
* Disable FSM, otherwise the PHY will auto suspend when no
* device is connected and will be reset on resume.
*/
reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1);
reg &= ~USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1);
usb2_eye_fix_7211b0(params);
}
static void usb_init_xhci(struct brcm_usb_init_params *params)
{
pr_debug("%s\n", __func__);
xhci_soft_reset(params, 0);
}
static void usb_uninit_common(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
pr_debug("%s\n", __func__);
USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
}
static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY];
u32 reg;
pr_debug("%s\n", __func__);
if (params->wake_enabled) {
USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN);
usb_wake_enable_7211b0(params, true);
} else {
USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN);
brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL);
reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL);
reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK;
brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL);
brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK,
usb_phy + USB_PHY_IDDQ);
}
}
static void usb_uninit_xhci(struct brcm_usb_init_params *params)
{
pr_debug("%s\n", __func__);
if (!params->wake_enabled)
xhci_soft_reset(params, 1);
}
static int usb_get_dual_select(struct brcm_usb_init_params *params)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
u32 reg = 0;
pr_debug("%s\n", __func__);
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
return reg;
}
static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode)
{
void __iomem *ctrl = params->regs[BRCM_REGS_CTRL];
u32 reg;
pr_debug("%s\n", __func__);
reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE);
reg |= mode;
brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1));
}
static const struct brcm_usb_init_ops bcm7216_ops = {
.init_ipp = usb_init_ipp,
.init_common = usb_init_common,
.init_xhci = usb_init_xhci,
.uninit_common = usb_uninit_common,
.uninit_xhci = usb_uninit_xhci,
.get_dual_select = usb_get_dual_select,
.set_dual_select = usb_set_dual_select,
};
static const struct brcm_usb_init_ops bcm7211b0_ops = {
.init_ipp = usb_init_ipp,
.init_common = usb_init_common_7211b0,
.init_xhci = usb_init_xhci,
.uninit_common = usb_uninit_common_7211b0,
.uninit_xhci = usb_uninit_xhci,
.get_dual_select = usb_get_dual_select,
.set_dual_select = usb_set_dual_select,
};
void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params)
{
pr_debug("%s\n", __func__);
params->family_name = "7216";
params->ops = &bcm7216_ops;
}
void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params)
{
pr_debug("%s\n", __func__);
params->family_name = "7211";
params->ops = &bcm7211b0_ops;
params->suspend_with_clocks = true;
}