2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-26 06:04:14 +08:00
linux-next/Documentation/driver-api/i2c.rst
Linus Torvalds 235b84fc86 Merge branch 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "This pull request contains:

   - i2c core reorganization. One source file became too monolithic. It
     is now split up, yet we still have the same named object as the
     final output. This should ease maintenance.

   - new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX

   - designware driver gained slave mode support

   - xgene-slimpro driver gained ACPI support

   - bigger overhaul for pca-platform driver

   - the algo-bit module now supports messages with enforced STOP

   - slightly bigger than usual set of driver updates and improvements

  and with much appreciated quality assurance from Andy Shevchenko"

* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
  i2c: Provide a stub for i2c_detect_slave_mode()
  i2c: designware: Let slave adapter support be optional
  i2c: designware: Make HW init functions static
  i2c: designware: fix spelling mistakes
  i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
  i2c: pca-platform: correctly set algo_data.reset_chip
  i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
  i2c: designware: enable SLAVE in platform module
  i2c: designware: add SLAVE mode functions
  i2c: zx2967: drop COMPILE_TEST dependency
  i2c: zx2967: always use the same device when printing errors
  i2c: pca-platform: use dev_warn/dev_info instead of printk
  i2c: pca-platform: use device managed allocations
  i2c: pca-platform: add devicetree awareness
  i2c: pca-platform: switch to struct gpio_desc
  dt-bindings: add bindings for i2c-pca-platform
  i2c: cadance: fix ctrl/addr reg write order
  i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
  dt: bindings: add documentation for zx2967 family i2c controller
  i2c: algo-bit: add support for I2C_M_STOP
  ...
2017-07-12 10:04:56 -07:00

49 lines
2.3 KiB
ReStructuredText

I\ :sup:`2`\ C and SMBus Subsystem
==================================
I\ :sup:`2`\ C (or without fancy typography, "I2C") is an acronym for
the "Inter-IC" bus, a simple bus protocol which is widely used where low
data rate communications suffice. Since it's also a licensed trademark,
some vendors use another name (such as "Two-Wire Interface", TWI) for
the same bus. I2C only needs two signals (SCL for clock, SDA for data),
conserving board real estate and minimizing signal quality issues. Most
I2C devices use seven bit addresses, and bus speeds of up to 400 kHz;
there's a high speed extension (3.4 MHz) that's not yet found wide use.
I2C is a multi-master bus; open drain signaling is used to arbitrate
between masters, as well as to handshake and to synchronize clocks from
slower clients.
The Linux I2C programming interfaces support the master side of bus
interactions and the slave side. The programming interface is
structured around two kinds of driver, and two kinds of device. An I2C
"Adapter Driver" abstracts the controller hardware; it binds to a
physical device (perhaps a PCI device or platform_device) and exposes a
:c:type:`struct i2c_adapter <i2c_adapter>` representing each
I2C bus segment it manages. On each I2C bus segment will be I2C devices
represented by a :c:type:`struct i2c_client <i2c_client>`.
Those devices will be bound to a :c:type:`struct i2c_driver
<i2c_driver>`, which should follow the standard Linux driver model. There
are functions to perform various I2C protocol operations; at this writing
all such functions are usable only from task context.
The System Management Bus (SMBus) is a sibling protocol. Most SMBus
systems are also I2C conformant. The electrical constraints are tighter
for SMBus, and it standardizes particular protocol messages and idioms.
Controllers that support I2C can also support most SMBus operations, but
SMBus controllers don't support all the protocol options that an I2C
controller will. There are functions to perform various SMBus protocol
operations, either using I2C primitives or by issuing SMBus commands to
i2c_adapter devices which don't support those I2C operations.
.. kernel-doc:: include/linux/i2c.h
:internal:
.. kernel-doc:: drivers/i2c/i2c-boardinfo.c
:functions: i2c_register_board_info
.. kernel-doc:: drivers/i2c/i2c-core-base.c
:export:
.. kernel-doc:: drivers/i2c/i2c-core-smbus.c
:export: