mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 20:53:53 +08:00
96ae38af9d
Convert the ti,fifo-depth from a TI specific property to the common tx-fifo-depth property. Also add support for the rx-fifo-depth. These are optional properties for this device and if these are not available then the fifo depths are set to device default values. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reported-by: Adrian Bunk <bunk@kernel.org> CC: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
69 lines
3.0 KiB
Plaintext
69 lines
3.0 KiB
Plaintext
* Texas Instruments - dp83867 Giga bit ethernet phy
|
|
|
|
Required properties:
|
|
- reg - The ID number for the phy, usually a small integer
|
|
- ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h
|
|
for applicable values. Required only if interface type is
|
|
PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID
|
|
- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
|
|
for applicable values. Required only if interface type is
|
|
PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID
|
|
|
|
Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays
|
|
will be left at their default values, as set by the PHY's pin strapping.
|
|
The default strapping will use a delay of 2.00 ns. Thus
|
|
PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no
|
|
internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree
|
|
should use "rgmii-id" if internal delays are desired as this may be
|
|
changed in future to cause "rgmii" mode to disable delays.
|
|
|
|
Optional property:
|
|
- ti,min-output-impedance - MAC Interface Impedance control to set
|
|
the programmable output impedance to
|
|
minimum value (35 ohms).
|
|
- ti,max-output-impedance - MAC Interface Impedance control to set
|
|
the programmable output impedance to
|
|
maximum value (70 ohms).
|
|
- ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the
|
|
board has RX_DV/RX_CTRL pin strapped in
|
|
mode 1 or 2. To ensure PHY operation,
|
|
there are specific actions that
|
|
software needs to take when this pin is
|
|
strapped in these modes. See data manual
|
|
for details.
|
|
- ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h
|
|
for applicable values. The CLK_OUT pin can also
|
|
be disabled by this property. When omitted, the
|
|
PHY's default will be left as is.
|
|
- ti,sgmii-ref-clock-output-enable - This denotes which
|
|
SGMII configuration is used (4 or 6-wire modes).
|
|
Some MACs work with differential SGMII clock.
|
|
See data manual for details.
|
|
|
|
- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
|
|
for applicable values (deprecated)
|
|
|
|
-tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for
|
|
the depth can be found in dt-bindings/net/ti-dp83867.h
|
|
-rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for
|
|
the depth can be found in dt-bindings/net/ti-dp83867.h
|
|
|
|
Note: ti,min-output-impedance and ti,max-output-impedance are mutually
|
|
exclusive. When both properties are present ti,max-output-impedance
|
|
takes precedence.
|
|
|
|
Default child nodes are standard Ethernet PHY device
|
|
nodes as described in Documentation/devicetree/bindings/net/phy.txt
|
|
|
|
Example:
|
|
|
|
ethernet-phy@0 {
|
|
reg = <0>;
|
|
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
|
|
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
|
|
tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
|
|
};
|
|
|
|
Datasheet can be found:
|
|
http://www.ti.com/product/DP83867IR/datasheet
|